Homepage Garage Wiki Register Community Calendar Today's Posts Search
#Camaro6
Go Back   CAMARO6 > Search Forums
Reload this Page Search Results


BeckyD @ James Martin Chevy


Page 1 of 17 1 234511 Last »
Showing results 1 to 30 of 500
Search took 0.09 seconds. Search: Posts Made By: KingLT1
Forum: 2016+ Camaro: 6th Gen Camaro general forum Yesterday, 10:35 AM
Replies: 26
Views: 1,261
Posted By KingLT1
Your lambda reading for both tunes at peak rpm is...

Your lambda reading for both tunes at peak rpm is .91-.93. That is lean imo but shouldn't cause misfires. I would fatten it up to .88-.89.

The heat range of plugs, fuel type, leaner AFR shouldn't...
Forum: ZL1 Discussions 10-29-2024, 10:19 AM
Replies: 33
Views: 1,096
Posted By KingLT1
That depends on your power level. I used to pull...

That depends on your power level. I used to pull 3.4 0-60 on the street when I just has basic bolt-ons. Now with 680-700whp it will hook from 40 with some heat in the tire. I have been a best of 3.0...
Forum: Dragstrip and Launching Discussion 10-28-2024, 09:09 AM
Replies: 5
Views: 346
Posted By KingLT1
Nice work! I don't have the patience for turbo...

Nice work! I don't have the patience for turbo stuff.
Forum: ZL1 Discussions 10-28-2024, 09:05 AM
Replies: 33
Views: 1,096
Posted By KingLT1
put them around 28-30psi for street use.

put them around 28-30psi for street use.
Forum: V8 - Engine, Exhaust, Bolt-Ons, Tuning Equipment 10-28-2024, 09:03 AM
Replies: 2
Views: 290
Posted By KingLT1
Valves closed it is damn close to the stock NPP....

Valves closed it is damn close to the stock NPP. It is truly mild to wild from closed to open.
Forum: Wheels | Tires -- Sponsored by The Tire Rack 10-28-2024, 08:52 AM
Replies: 9
Views: 613
Posted By KingLT1
Yeah, I believe so. I don't think you can make a...

Yeah, I believe so. I don't think you can make a 20" lighter and maintain its structural integrity without going full Carbon or something. That is like 10lbs per wheel lighter than stock.
Forum: V8 LT1 Engine, Exhaust, and Bolt-Ons 10-28-2024, 08:48 AM
Replies: 9
Views: 582
Posted By KingLT1
I just put the sport muffler version on...

I just put the sport muffler version on mine(Corsa sent to me at no charge) because I was tired of the valve issue. And it's in between the level of closed and open of the NPP. Actually, it sounds...
Forum: 2016+ Camaro: 6th Gen Camaro general forum 10-28-2024, 08:37 AM
Replies: 25
Views: 1,436
Posted By KingLT1
The 6th gen diff is plenty strong. Most issues...

The 6th gen diff is plenty strong. Most issues are from not changing the fluid. Guys have been running 8's and 1.3 60fts with no real issues. The driveshaft and axles are the weakest link but still...
Forum: 2016+ Camaro: 6th Gen Camaro general forum 10-27-2024, 10:55 AM
Replies: 25
Views: 1,436
Posted By KingLT1
5th gen is nice, but the 6th gen is improved in...

5th gen is nice, but the 6th gen is improved in every way other than room. You need a FBO 5th gen to run with a stock 6th gen straight line. On a road course it will never come close. A 6th gen...
Forum: Wheels | Tires -- Sponsored by The Tire Rack 10-27-2024, 10:35 AM
Replies: 9
Views: 613
Posted By KingLT1
I was told the 20" Scelus are in the low 20lb per...

I was told the 20" Scelus are in the low 20lb per range.
Forum: V8 - Engine, Exhaust, Bolt-Ons, Tuning Equipment 10-26-2024, 03:51 PM
Replies: 2
Views: 290
Posted By KingLT1
Corsa NPP

Have a Corsa NPP axle back for sale. Driver side valve has a intermittent rattle when the valve is closed. Corsa initially sent me a service kit that required removing the button head end of the...
Forum: Wheels | Tires -- Sponsored by The Tire Rack 10-26-2024, 09:14 AM
Replies: 9
Views: 613
Posted By KingLT1
I actually have a set on order. They offer a ton...

I actually have a set on order. They offer a ton of finish options and are custom built to order. I am doing a set of Scelus in Vacuum Chrome. 20x9.5 ET25 front and 20x10.5 ET38 rear. The owner has...
Forum: 2016+ Camaro: 6th Gen Camaro general forum 10-25-2024, 03:57 PM
Replies: 26
Views: 1,261
Posted By KingLT1
Tunes don't magically change. So if it ran good...

Tunes don't magically change. So if it ran good on the "aggressive" tune prior, it's not the tune.
Forum: Transmissions 10-25-2024, 10:52 AM
Replies: 7
Views: 369
Posted By KingLT1
TH400 is race car stuff. There are so many other...

TH400 is race car stuff. There are so many other platforms that you can turn into a race car easier and cheaper than a 6th gen. What makes the 6th gen nice is how comfortable it is and how well it...
Forum: 2016+ Camaro: 6th Gen Camaro general forum 10-25-2024, 08:54 AM
Replies: 26
Views: 1,261
Posted By KingLT1
If you have an intake leak between the MAF and TB...

If you have an intake leak between the MAF and TB your fuel trims will go extremely positive at idle. It will also throw off the fueling in PE mode since unmetered air is entering the system.

The...
Forum: ZL1 Discussions 10-25-2024, 08:43 AM
Replies: 20
Views: 1,054
Posted By KingLT1
I run Delco filters with China writing (they all...

I run Delco filters with China writing (they all are that way now) on the daily, But the Camaro gets a K&N HP1017. I like the welded nut on the bottom... makes it easier to get off.
Forum: Transmissions 10-25-2024, 08:35 AM
Replies: 7
Views: 369
Posted By KingLT1
Yes there is a company offering conversions now....

Yes there is a company offering conversions now. It's been popular for the CTS-V3 and Truck crowd. It makes the most sense if your vehicle has a A4/A6. Everybody shits on the 8l90 but I think they...
Forum: V8 LT1 Engine, Exhaust, and Bolt-Ons 10-24-2024, 07:45 AM
Replies: 9
Views: 582
Posted By KingLT1
Agree...Stock, Flowmaster, Corsa. All ended up...

Agree...Stock, Flowmaster, Corsa. All ended up doing it. The good thing about Corsa is their warranty and CS is pretty good. They now send out service kits for the gen 2 valve systems, but my...
Forum: V8 LT1 Engine, Exhaust, and Bolt-Ons 10-22-2024, 08:35 AM
Replies: 9
Views: 582
Posted By KingLT1
Not AWE but I bolted Corsa NPP mufflers to a...

Not AWE but I bolted Corsa NPP mufflers to a Borla X pipe with no issue. I will warn you that Corsa has problems with the valves rattling. They now provide service kits for the valves. Basically, the...
Forum: V8 LT1 Engine, Exhaust, and Bolt-Ons 10-19-2024, 08:30 AM
Replies: 31
Views: 4,167
Posted By KingLT1
I think you posted before finishing your coffee.

I think you posted before finishing your coffee.
Forum: 2016+ Camaro: 6th Gen Camaro general forum 10-17-2024, 02:47 PM
Replies: 11
Views: 1,147
Posted By KingLT1
I remember your car! I always liked that setup. ...

I remember your car! I always liked that setup. I had the same heads but slightly smaller cam and ported fast 92.

Sewing machine just means you can hear the valves closing. Sounds like a clicking...
Forum: 2016+ Camaro: 6th Gen Camaro general forum 10-17-2024, 02:38 PM
Replies: 24
Views: 1,452
Posted By KingLT1
Bingo

Bingo
Forum: 2016+ Camaro: 6th Gen Camaro general forum 10-17-2024, 01:21 PM
Replies: 11
Views: 1,147
Posted By KingLT1
Yep I get it...I was the same way back when I...

Yep I get it...I was the same way back when I installed heads/cam in Fbody Camaro with a LS1. It had the sewing machine sound. I went with a mild low lift cam in a 5.3 for my Yukon and it's quiet...
Forum: 2016+ Camaro: 6th Gen Camaro general forum 10-17-2024, 10:18 AM
Replies: 11
Views: 1,147
Posted By KingLT1
As mentioned in the other thread. High lift...

As mentioned in the other thread.

High lift cam, high lift dual valve springs, long tube headers = sewing machine sound. It will be more noticeable with the windows up through the firewall.
...
Forum: Forced Induction Discussions 10-16-2024, 08:15 AM
Replies: 63
Views: 15,739
Posted By KingLT1
He will turn it up and run it out of low side...

He will turn it up and run it out of low side next. :D
Forum: ZL1 Discussions 10-16-2024, 08:14 AM
Replies: 18
Views: 1,003
Posted By KingLT1
LS and LT engines have 1 coil for each cylinder...

LS and LT engines have 1 coil for each cylinder and a plug wire that is less than 12" long. There haven't been any gains to had changing from OEM since 1997 when the LS1 debuted. As Josh mentioned...
Forum: 2016+ Camaro: 6th Gen Camaro general forum 10-14-2024, 08:32 AM
Replies: 24
Views: 1,452
Posted By KingLT1
They probably recommend unplugging it to keep...

They probably recommend unplugging it to keep from draining the battery.
Forum: ZL1 Discussions 10-14-2024, 08:30 AM
Replies: 17
Views: 951
Posted By KingLT1
As I just posted...MANUAL cars using STD...

As I just posted...MANUAL cars using STD correction on a dynojet often dyno 570-580whp bone stock. using SAE correction that would be 560-570whp. A10's normally dyno 540-550whp SAE.

Your car is...
Forum: ZL1 Discussions 10-13-2024, 09:02 AM
Replies: 17
Views: 951
Posted By KingLT1
Those are not uncommon numbers for a manual car...

Those are not uncommon numbers for a manual car in STD. They tend to dyno higher than A10 stuff. I agree the torque is low, but without a data log it's hard to say. Maybe try a little VP octanium and...
Forum: Forced Induction Discussions 10-13-2024, 08:56 AM
Replies: 30
Views: 1,287
Posted By KingLT1
Too much Ford pron...unfollowing.

Too much Ford pron...unfollowing.
Showing results 1 to 30 of 500
Page 1 of 17 1 234511 Last »

 
Forum Jump

All times are GMT -5. The time now is 07:07 PM.

Contact Us - CAMARO6 - Archive - Privacy Statement - Terms of Service / DMCA Policy - Top

Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.