Bose Wiring Diagram - Page 4

chris227 · 03-26-2016, 03:25 PM

Had no problem with the amp turning on after having the x3 connector unplugged all night. Everything still works as normal just the bass does not drop like it did with it connected.

chris227 · 04-03-2016, 01:47 PM

After having the X3 connector disconnected for a couple weeks now, I love the stereo much more. One side effect is I don't get the ticking sound when I turn on my blinker. Reconnected it the other day to make sure it wasn't something else and the sound was back. IMO sounds better with X3 disconnected.

A_Work_Of_Art · 07-19-2016, 04:42 PM

Reviving an old thread.

Does anyone have the wire diagram for the x3 connector? I am getting sound issues that could be related to the ANC and I need to know what wire to clip for the Mic on the x3 connector. Thanks in advance fellas!

- Art

Skydiver32 · 07-27-2016, 08:22 PM

Quote:

Originally Posted by gblaue

You can ask me questions, I'll answer what I can, but I am limited to what I can answer.

For the 1SS...Do you have any suggestions as to where to tap for a remote? /Thanks..

shags · 01-22-2017, 06:24 PM

Quote:

Originally Posted by Skydiver32

For the 1SS...Do you have any suggestions as to where to tap for a remote? /Thanks..

im looking for the same

NY Andrew · 01-22-2017, 06:26 PM

http://www.camaro6.com/forums/showthread.php?t=474059

ctrlz · 03-20-2017, 07:59 PM

The below image shows a Bose amp in a 2LT.
The connectors right to left are X1 (black), X2 (green), X3 (black), and X4 (brown). The X1 and X2 connectors are the same for all Bose installations.
X3 varies with installations in a 2SS getting additional wires.
In this photo X3 has only one wire (gray with green stripe, GY/GN) in pin 1 - Low speed GM LAN serial data.
X4 has 4 wires in pins 3-6:
3 WH/GN MOST serial data (-)
4 GY/VT MOST serial data (+)
5 WH/GN MOST serial data (-)
6 GY/VT MOST serial data (+)
pin 14 is WH/VT MOST control, and I believe it is hidden here. It is definitely present on the 2SS harness.

Antista1974 · 03-24-2017, 11:14 PM

you cant fade to right because you are connected to the left only....but you are also louder now because you basically bridged your wires...you went from 4 wires to 2 which changed/doubled your power probably changed your ohms from 8 to 4 or 4 to 2 or 2 to1 especially if you are using a mono block amp....which most after market sub amps are mono block...

mako22 · 10-02-2017, 11:56 AM

Quote:

Originally Posted by ctrlz

The below image shows a Bose amp in a 2LT.
The connectors right to left are X1 (black), X2 (green), X3 (black), and X4 (brown). The X1 and X2 connectors are the same for all Bose installations.
X3 varies with installations in a 2SS getting additional wires.
In this photo X3 has only one wire (gray with green stripe, GY/GN) in pin 1 - Low speed GM LAN serial data.
X4 has 4 wires in pins 3-6:
3 WH/GN MOST serial data (-)
4 GY/VT MOST serial data (+)
5 WH/GN MOST serial data (-)
6 GY/VT MOST serial data (+)
pin 14 is WH/VT MOST control, and I believe it is hidden here. It is definitely present on the 2SS harness.

Thanks for this - so if I wanted to cut the wires for active noise cancellation in my 2SS - which wires would I cut?

Ecchi667 · 10-02-2017, 01:36 PM

Quote:

Originally Posted by mako22

Thanks for this - so if I wanted to cut the wires for active noise cancellation in my 2SS - which wires would I cut?

See post 9 here:

http://www.camaro6.com/forums/showthread.php?t=506670

Should make sense from that I hope.

mako22 · 10-02-2017, 08:18 PM

Quote:

Originally Posted by Ecchi667

See post 9 here:

http://www.camaro6.com/forums/showthread.php?t=506670

Should make sense from that I hope.

Thanks!!!

Sai B. · 06-29-2019, 01:08 AM

Quote:

Originally Posted by BadBillyJack

Not saying you did something wrong, but I do believe you looked at the wrong schematics.

Where did you get this information? Cause I can’t find a service manual anywhere.

WiggyB · 01-02-2022, 08:53 PM

Took me about 2 hours because I was being picky. But simple hookup for those wanting to add aftermarket subs to your 6th gen. Granted this is in a 2SS with the bose system but I didn't use anything off the bose amp I used the drivers side rear speaker. For those without the bose setup you can run off one of the rear side speakers.

1. Hooked up the kicker sub converter to the rear speaker on the passenger side. BU/GY Left/Rear Subwoofer Speaker Control (+),
and GN/BK Left/Rear Subwoofer Speaker (-)
2. Ran the power wire to the battery with a fuse link in the line.
3. Made my own ground point as you can see the brown wire in the picture.
4. Ran the remote lead from the kicker converter to the amp.

Could have been done in 1 hour but I kept running back to autozone for stuff i thought I had but couldn't find anything.

07-19-2016, 04:42 PM	#45
A_Work_Of_Art Drives: 2016 Camaro SS Join Date: Apr 2016 Location: Guam Posts: 31	Reviving an old thread. Does anyone have the wire diagram for the x3 connector? I am getting sound issues that could be related to the ANC and I need to know what wire to clip for the Mic on the x3 connector. Thanks in advance fellas! - Art __________________ \| 2SS Camaro \|Garnet Red\| Adrenaline Red\| NPP\| MRC\| 6SPD\| CAI Intake\| Mishimoto CC\|

01-22-2017, 06:26 PM	#48
NY Andrew Drives: 2016 Camaro V6 2LT RS Fully Loaded Join Date: Sep 2015 Location: VA Posts: 474	http://www.camaro6.com/forums/showthread.php?t=474059 __________________ Borla ATAK w/ Midpipe, VMAX TB, K&N Filter, Subwoofer, Tinted, AFM Disabler, Vitesse Throttle Controller! ORDERED:08/19/15 DELIVERED:12/09/15 My 2LT Review/Pictures/Mustang Comparison My 2016 Camaro Bose Subwoofer Install 2016 Camaro V6 Stock to Borla Atak Exhaust Sound 2016 Camaro V6 Resonator & X-Pipe Replace with Midpipe & Borla Atak

03-20-2017, 07:59 PM	#49
ctrlz Drives: 2017 2SS, 50th pkg, M6, MRC, NPP Join Date: Jan 2016 Location: Ocean City, NJ Posts: 3,183	The below image shows a Bose amp in a 2LT. The connectors right to left are X1 (black), X2 (green), X3 (black), and X4 (brown). The X1 and X2 connectors are the same for all Bose installations. X3 varies with installations in a 2SS getting additional wires. In this photo X3 has only one wire (gray with green stripe, GY/GN) in pin 1 - Low speed GM LAN serial data. X4 has 4 wires in pins 3-6: 3 WH/GN MOST serial data (-) 4 GY/VT MOST serial data (+) 5 WH/GN MOST serial data (-) 6 GY/VT MOST serial data (+) pin 14 is WH/VT MOST control, and I believe it is hidden here. It is definitely present on the 2SS harness. Last edited by ctrlz; 03-20-2017 at 08:30 PM.

01-02-2022, 08:53 PM	#55
WiggyB Drives: 2022 Camaro 2SS 1LE Join Date: Nov 2021 Location: NC Posts: 277	Easy Amp Installation Took me about 2 hours because I was being picky. But simple hookup for those wanting to add aftermarket subs to your 6th gen. Granted this is in a 2SS with the bose system but I didn't use anything off the bose amp I used the drivers side rear speaker. For those without the bose setup you can run off one of the rear side speakers. 1. Hooked up the kicker sub converter to the rear speaker on the passenger side. BU/GY Left/Rear Subwoofer Speaker Control (+), and GN/BK Left/Rear Subwoofer Speaker (-) 2. Ran the power wire to the battery with a fuse link in the line. 3. Made my own ground point as you can see the brown wire in the picture. 4. Ran the remote lead from the kicker converter to the amp. Could have been done in 1 hour but I kept running back to autozone for stuff i thought I had but couldn't find anything. Attached Images

03-26-2016, 03:25 PM	#43
chris227 Drives: 2020 Camaro 2SS Join Date: Aug 2009 Location: Sherman,Texas Posts: 844	Had no problem with the amp turning on after having the x3 connector unplugged all night. Everything still works as normal just the bass does not drop like it did with it connected.

04-03-2016, 01:47 PM	#44
chris227 Drives: 2020 Camaro 2SS Join Date: Aug 2009 Location: Sherman,Texas Posts: 844	After having the X3 connector disconnected for a couple weeks now, I love the stereo much more. One side effect is I don't get the ticking sound when I turn on my blinker. Reconnected it the other day to make sure it wasn't something else and the sound was back. IMO sounds better with X3 disconnected.

03-24-2017, 11:14 PM	#50
Antista1974 Drives: 2016 Camaro 2ss 2nd cat delete Join Date: Jan 2017 Location: San Antonio Posts: 34	you cant fade to right because you are connected to the left only....but you are also louder now because you basically bridged your wires...you went from 4 wires to 2 which changed/doubled your power probably changed your ohms from 8 to 4 or 4 to 2 or 2 to1 especially if you are using a mono block amp....which most after market sub amps are mono block...

User Name		Remember Me?
Password