bmr engine mounts - Page 3

Dubchitts · 02-05-2018, 11:26 AM

Quote:

Originally Posted by blk 2013

will these mounts pass a lot of vibration to the body of car?

It says they may increase this (something along these lines, as the poly is stuffer than the oem rubber. And they're made for performance not comfort). I don't expect them to be that bad, but not as comfy as oem.

Quote:

Originally Posted by Goohead

Let us know the ride quality

It's going to be at least April before my car comes out of winter storage. Lol.

L78toLT1 · 02-05-2018, 04:01 PM

Hey Dubchitts, have u fired your car since getting the motor back in? I'm interested in how your Pray performance strategy 1 cam sounds.

Dubchitts · 02-05-2018, 04:20 PM

Quote:

Originally Posted by L78toLT1

Hey Dubchitts, have u fired your car since getting the motor back in? I'm interested in how your Pray performance strategy 1 cam sounds.

No. I'm saving for the tune right now. I'm not in a huge hurry since I can't get it out til April anyway

PRAY · 02-05-2018, 04:29 PM

Quote:

Originally Posted by Dubchitts

They didn't send the plates that mount to the cradle. This after they didn't send my package for a week:/

LOL. I just got a set that didn't have the mount plates either. So I am stuck waiting to get the motor in the car I have here.

PRAY · 02-05-2018, 04:30 PM

Quote:

Originally Posted by L78toLT1

Hey Dubchitts, have u fired your car since getting the motor back in? I'm interested in how your Pray performance strategy 1 cam sounds.

Go to my FB page, @prayperformance. There is a not to awesome vid on there of it. You can hear is settle at the end.

Dubchitts · 02-05-2018, 04:30 PM

Quote:

Originally Posted by PRAY

LOL. I just got a set that didn't have the mount plates either. So I am stuck waiting to get the motor in the car I have here.

Damnnit bmr lol. Those are a dream to install compared to what I imagine the stock mounts are like tho

PRAY · 02-05-2018, 04:36 PM

Quote:

Originally Posted by Dubchitts

Damnnit bmr lol. Those are a dream to install compared to what I imagine the stock mounts are like tho

I leave the mounts on the engine and but pull the ones on the frame. Motor goes right in. Then I put the frame mounts back on.

So it appears the mount with the spacers is the pass side.

L78toLT1 · 02-06-2018, 06:24 AM

Hey Brett, since I will be likely following in Dubchitts's footsteps with your stage 1 package I was wondering how you will handle the remote tune. Do you email an initial tune then datalog to dial in the final tune?

PRAY · 02-06-2018, 06:47 AM

Quote:

Originally Posted by L78toLT1

Hey Brett, since I will be likely following in Dubchitts's footsteps with your stage 1 package I was wondering how you will handle the remote tune. Do you email an initial tune then datalog to dial in the final tune?

Yes, I will be offering remote tuning for my H/C set ups. I will be finishing up a modified SGT 1 project this week that will give me good tuning data for this combo.

L78toLT1 · 02-06-2018, 07:13 AM

Dubchitts's and I have most identical cars / mods. Only difference mod wise is his 3" exhaust - we even have your favorite CAI lol. He's a '17 vs my '16 but otherwise we are identical. His tune should give us a good baseline when I get around to doing mine

Razor427 · 04-12-2018, 06:29 PM

I ordered the other mounts.... will install when I do my headers.

http://http://m.bmrsuspension.com/?p...productid=1777

Ray

Dubchitts · 04-12-2018, 07:31 PM

I have gotten mine out and the ride quality is good! The car does shake at an idle, but you can't really tell sitting inside (mrc). I only realized it shakes after my neighbor noticed it while we were talking lol. Overall Im happy with them. I would possibly put a very small amount of thread locker on the mounting bolts(just a thread or 2 just to keep it from getting loose), or use some lock washers. I noticed while doing an oil change 2 were a little loose.

Re torqued and will keep an eye on them!

sage85z28 · 09-17-2020, 11:15 AM

Hate to bring this back from the dead but has anyone installed the MM009 mounts with pics?

laynlo15 · 09-26-2020, 02:21 PM

Name: 20190128_081833.jpg
Views: 431
Size: 123.2 KB

I might have some pic of the mounts. Lots more room around the side of the engine plus you save about 18 lbs getting rid of the hydraulic mounts.

02-05-2018, 04:01 PM	#30
L78toLT1 Drives: Hyper Blue 2016 2SS 6M Join Date: Sep 2017 Location: North Ga Posts: 1,810	Hey Dubchitts, have u fired your car since getting the motor back in? I'm interested in how your Pray performance strategy 1 cam sounds. __________________ Baby Blue 2016 Hyper Blue 2SS/6m/MRC/NPP/Silver Rally stripes/ZL1 wheels & brakes/GForce DS and axles/ZLE Cradle Bushings/FE4 ARB front & rear/SEMA Grill/Rotofab dry/95mm TB/Magnuson 2300/Full LT4 fuel system/JMS boost-a-pump/E85 Sensor/Ported CID heads from LME/Cammotion PD cam/Thompson Motorsports forged shortblock/catted Kooks 1 7/8 headers /JRE remote tuned

02-06-2018, 06:24 AM	#36
L78toLT1 Drives: Hyper Blue 2016 2SS 6M Join Date: Sep 2017 Location: North Ga Posts: 1,810	Hey Brett, since I will be likely following in Dubchitts's footsteps with your stage 1 package I was wondering how you will handle the remote tune. Do you email an initial tune then datalog to dial in the final tune? __________________ Baby Blue 2016 Hyper Blue 2SS/6m/MRC/NPP/Silver Rally stripes/ZL1 wheels & brakes/GForce DS and axles/ZLE Cradle Bushings/FE4 ARB front & rear/SEMA Grill/Rotofab dry/95mm TB/Magnuson 2300/Full LT4 fuel system/JMS boost-a-pump/E85 Sensor/Ported CID heads from LME/Cammotion PD cam/Thompson Motorsports forged shortblock/catted Kooks 1 7/8 headers /JRE remote tuned

02-06-2018, 07:13 AM	#38
L78toLT1 Drives: Hyper Blue 2016 2SS 6M Join Date: Sep 2017 Location: North Ga Posts: 1,810	Dubchitts's and I have most identical cars / mods. Only difference mod wise is his 3" exhaust - we even have your favorite CAI lol. He's a '17 vs my '16 but otherwise we are identical. His tune should give us a good baseline when I get around to doing mine __________________ Baby Blue 2016 Hyper Blue 2SS/6m/MRC/NPP/Silver Rally stripes/ZL1 wheels & brakes/GForce DS and axles/ZLE Cradle Bushings/FE4 ARB front & rear/SEMA Grill/Rotofab dry/95mm TB/Magnuson 2300/Full LT4 fuel system/JMS boost-a-pump/E85 Sensor/Ported CID heads from LME/Cammotion PD cam/Thompson Motorsports forged shortblock/catted Kooks 1 7/8 headers /JRE remote tuned

04-12-2018, 07:31 PM	#40
Dubchitts Drives: '17 Red hot 2ss, 16 Focus RS Join Date: Aug 2015 Location: Michigan Posts: 845 View My Garage	I have gotten mine out and the ride quality is good! The car does shake at an idle, but you can't really tell sitting inside (mrc). I only realized it shakes after my neighbor noticed it while we were talking lol. Overall Im happy with them. I would possibly put a very small amount of thread locker on the mounting bolts(just a thread or 2 just to keep it from getting loose), or use some lock washers. I noticed while doing an oil change 2 were a little loose. Re torqued and will keep an eye on them! __________________ "Spitfire" 427ci 2017 Red Hot 2SS// 6 Piston Brembos//Adrenaline Red Interior, Knee Pads//M6//MRC Afe Air Filter//BMR MM010 Motor Mounts, Safety Loop//Custom OTR Intake//Flex Fuel Kit//Gforce 3.5" Aluminum Driveshaft//GM 95mm TB//Katech Oil Pump, Piston Squirters//Kooks 1-7/8 LT//LT4 Fueling//Mighty Mouse Wild//Monster Clutch LT1-S Triple Disc//MSD 2-Step//Pray Performance Custom Spec Cam, Ported Holley Hi-Ram//Sikky 12" Shifter w OEM Knob Mod//Tick Level 1 Tr6060//Labor by Me//Tune By Pray Performance

04-12-2018, 06:29 PM	#39
Razor427 Drives: 2016 Camaro 1SS Join Date: Feb 2018 Location: S.Florida Posts: 75	I ordered the other mounts.... will install when I do my headers. http://http://m.bmrsuspension.com/?p...productid=1777 Ray

09-17-2020, 11:15 AM	#41
sage85z28 Drives: 2017 1SS cruiser/ 1985 Z28 racecar Join Date: Nov 2018 Location: Annapolis MD Posts: 77	Hate to bring this back from the dead but has anyone installed the MM009 mounts with pics?

09-26-2020, 02:21 PM	#42
laynlo15 Drives: 2022 Lt1 A10 Join Date: Nov 2015 Location: clark, mo Posts: 8,882	I might have some pic of the mounts. Lots more room around the side of the engine plus you save about 18 lbs getting rid of the hydraulic mounts.

User Name		Remember Me?
Password