12-01-2020, 09:33 AM | #15 | |
Drives: 2017 Silverado/2017 ZL1 Join Date: Aug 2019
Location: Jax/Palatka FL
Posts: 1,090
|
Quote:
__________________
|
|
12-02-2020, 03:18 PM | #16 | ||
CamaroFans.com
|
Quote:
The Mag Pad positioned in the center is all I ever need for changing tires back and forth. I sort of wanted to try the jack pads to try and make changing camber on the ZLE a bit easier with both fronts off the ground so the sway bar connecting the two sides will move around easier. Quote:
|
||
12-29-2020, 12:30 PM | #17 |
Lethal Camaro
Drives: 16 2SS, 71 Std, Suburban RTS Join Date: Jun 2013
Location: Temecula, CA
Posts: 3,855
|
Just to jump in here being an employee of ZL1 Addons and also being the one who made the linked video.
You should avoid putting jack stands on a pinch weld period unless you have a pinch weld designed stand. Jack stands are not designed for that sort of placement. The main body of the unibody is a perfect solid point to put stands as outlined in the video. I know of 5 performance shops that only use those points. You just want to make sure you have it under an area that offers enough space on both sides so the car sits nice and flat and even if it did slip, it's going nowhere. I have pulled the motor and had my car hovering on these spots for years based on the suggestion of the shops I have talked to. All of them avoid the pinch welds. The ZL1 products are designed to work with Lifts and floor jacks. Never use them with a jack stand. Your car with the ZL1 Addons products on a Jack stand is very dangerous and can easily slide off the stands.
__________________
|
12-29-2020, 05:36 PM | #18 |
Drives: 2019 Camaro 2SS Join Date: Aug 2020
Location: McCordsville, Indiana
Posts: 621
|
I agree that they shouldn’t be used with standard jack stands, however I have no concerns personally using the ESCO style stands mentioned above with the lift pads. No different then mounting pads on a lift.
__________________
2019 Shock 2SS A10. 2650@10psi/LPE HPFP/XDI+30/LT4 LPFP+JMS/Soler 95mm/Rotofab, E65, CSP 2” Headers/GESI GenII Cats. MM Wild/GM SG3 suspension/1LE Brakes, Velgen VF5 Wheels/GY SC3. JRE Tuned.
|
12-29-2020, 08:49 PM | #19 |
Drives: Wild Cherry LT1 Join Date: Dec 2016
Location: Massachusetts
Posts: 1,925
|
I agree on the unibody points as being the best secure jack stand locations. However, for me, the potential of being crushed, scares the hell out of me. I won’t place my body under a car with just one form of support that has three failure points (IE pinch weld - to puck - to hydraulic jack). That’s right, I freely admit, I’m a chicken. I’d more than likely utilize the Esco type design as a secondary back up at another pinch weld, prior to sliding another jack stand and my body under the car.
Only reason I say this is I’ve seen some bad things happen to safety conscience people... more is always better when it comes to safety. For me, it took being electrocuted, a close call on a moss covered roof, a ladder failure, hoisting pick point failure and personally witnessing deaths / maiming of others to realize unexpected / stupid shit happens. Last edited by Chutzpah; 12-29-2020 at 09:59 PM. |
12-29-2020, 10:12 PM | #20 | |
Lethal Camaro
Drives: 16 2SS, 71 Std, Suburban RTS Join Date: Jun 2013
Location: Temecula, CA
Posts: 3,855
|
Quote:
__________________
|
|
12-29-2020, 11:07 PM | #21 |
Drives: 2020 Zl1 A10 Riverside Blue Join Date: Mar 2020
Location: NJ
Posts: 1,220
|
I personally have a quick jack which I believe is great, but before pulling the trigger on it. I looked into this jackstand that has the pinch weld adapter and you use a jack to set it up. Has anyone used them before?
|
12-30-2020, 11:05 AM | #22 | |
Drives: 2021 Camaro ZL1 A10 Join Date: May 2013
Location: San Diego, CA.
Posts: 457
|
Quote:
|
|
12-30-2020, 11:38 AM | #23 |
Drives: 2021 Camaro ZL1 A10 Join Date: May 2013
Location: San Diego, CA.
Posts: 457
|
I see this thread has been revived.
I have since changed my oil. I followed Lethal Garages video. Even going to Harbor Freight and getting two 3 ton floor jacks. I had forgotten that my aluminum floor jack was only 2 ton. I guess with old age I am not as adventurous about lifting and getting under the car. I lifted the Camaro on one side and was sliding my jack stand under the frame. But looking at the underside of the chassis I didn't feel comfortable with placing the jack stand there. I think it could cause some minor damage on other things under the chassis. This is just me. I have no doubt that this point will support the car on jack stands. While this is not recommended. I have the ZL1 addon lift pads on installed. With rubber boots on the typical jack stands and placed them under the jack pads. With the jack stand and floor jack supporting one side of the car, I lifted the other side of the car and placed a jack stand on the forward jack pad (with a rubber boot on the jack stand). My intent was the lift the rear of the car, and place it on all four jack stands. However, with the suitcase muffler, accessing the rear cross member was difficult. Trying to place jack stands on the rear by lifting from the sides of the chassis proved to be a bad idea. So with just the front end on jack stands, I changed the oil. I'll change the differential fluid when I can get the car on a lift. There may be a Quickjack in my future. Funny thing. I sold the White 1SS 1LE to Carmax a week later and bought a Shadow Grey Metallic ZL1 A10. |
12-30-2020, 05:18 PM | #24 |
Geoff
Drives: 2020 ZL1 Green Join Date: May 2013
Location: Houston
Posts: 1,720
|
Some people are pretty clever. I saw this at the track the other day, it seemed quite slick.
http://www.jackpointjackstands.com The top portion goes on your floor jack pad, slide under your pinch point, jack the car up and slide the base around the jack, lower jack and repeat to lift the car. The guy using it, did one side at a time on a BMW. A bit pricey, but what is the price for peace of mind? No, I don't have any. I use quick jack and ZL1 addons bolt on pads
__________________
|
12-30-2020, 06:34 PM | #25 | ||
CamaroFans.com
|
Quote:
|
||
12-30-2020, 07:01 PM | #26 |
Drives: Wild Cherry LT1 Join Date: Dec 2016
Location: Massachusetts
Posts: 1,925
|
|
12-30-2020, 07:14 PM | #27 |
Geoff
Drives: 2020 ZL1 Green Join Date: May 2013
Location: Houston
Posts: 1,720
|
Yup, pricey. But cheaper than a quick jack
__________________
|
12-31-2020, 01:37 PM | #28 |
Drives: SWXXZL1 Join Date: Jul 2020
Location: the corrupt purple state of az
Posts: 150
|
I have a home shop four post lift, but I can see those as being very useful. Hope china doesn't copy the idea and diminish the guy's work.
__________________
"Joe" does a hilarious impression of a slinky toy on stairs.
|
|
|
Post Reply
|
|
|