You are browsing camaro6 
09-05-2018, 07:18 PM
|
#1 |
 Drives: ZL1 Finally Join Date: Aug 2018
Location: Seattle
Posts: 114
|
ZL1 A10 max negative camber
Anybody tracking ZL1 A10 can comment on max negative camber they can achieve without any mod? If you have to mod to get more negative camber, what's the mod?
|
|
|
|
09-05-2018, 07:49 PM
|
#2 |
  Drives: ISO ss 1le Join Date: May 2018
Location: FL
Posts: 764
|
Talk to TravisLambert on here. He’s got a zl1.
https://www.camaro6.com/forums/showthread.php?t=526353 |
|
|
|
|
09-05-2018, 09:55 PM
|
#3 |
 
Drives: 2016 Camaro 2SS Join Date: Jun 2017
Location: San Diego
Posts: 201
|
You can also install a camber plate. That's what I did
|
|
|
|
|
09-05-2018, 10:16 PM
|
#4 | |
|
Drives: ZL1 Finally Join Date: Aug 2018
Location: Seattle
Posts: 114
|
Quote:
 What camber plate did you get? Is it for front only? Rear should be able to achieve -2 deg by stock setup right?
|
|
|
|
|
|
09-05-2018, 10:19 PM
|
#5 |
   
Drives: Crush ZLE M6 | 2000 Corvette FRC Join Date: Jun 2010
Location: Cencal
Posts: 1,659
|
I have seen guys with stock junk achieve -2.5 -–> -2.9 on here.
|
|
|
|
|
09-05-2018, 11:33 PM
|
#6 | |
|
Drives: 2016 Camaro 2SS Join Date: Jun 2017
Location: San Diego
Posts: 201
|
Quote:
https://www.camaro6.com/forums/showthread.php?t=501824 Looks like their website is down. I don't know what happened. But a lot of people on this forum have bought their camber plates. Some people may sell theirs when they decide to sell their car. The camber plate can give you 2 more degrees of negative camber and can also lower the car if you want. Quality is good and I've been using them for 15 hours of track driving. No problem. Only one guy ran into problem but it turned out he installed the camber plate in a wrong way which caused the failure I don't know if there is other camber plate for our car |
|
|
|
|
|
09-05-2018, 11:43 PM
|
#7 | |
|
Drives: ZL1 Finally Join Date: Aug 2018
Location: Seattle
Posts: 114
|
Quote:
Thanks! Anybody in Seattle area know a good chevy shop to install these camber plates professionally? |
|
|
|
|
|
09-06-2018, 08:45 PM
|
#8 |
 
Drives: 2018 ZL1 Join Date: Jan 2018
Location: Illinois
Posts: 25
|
We have an '18 ZL1 A10 and got up to 2.9 on the front with no mods. Dialed it back to 2.6 on both sides as we are running 19 x 10.5 wheels up front with 305s. No trimming and no rubbing.
|
|
|
|
|
09-06-2018, 11:40 PM
|
#9 | |
|
Drives: ZL1 Finally Join Date: Aug 2018
Location: Seattle
Posts: 114
|
Quote:
|
|
|
|
|
|
09-07-2018, 05:06 PM
|
#10 |
     
Drives: '21 ZLE A10 Join Date: May 2012
Location: Mechanicsville, VA
Posts: 6,813
|
-2.4° max was all my car would allow
__________________
'21 ZLE A10 Wild Cherry PDR 2:00.78 VIR Full 10.68@131.69 1.68 60'
'17 ZL1 A10 Mosaic Black PDR/Nav 2:03.08 VIR Full 11.003@129.2 1.75 (sold) '15 Z/28 #325 Black a/c & stereo. 2:10.1 VIR Full (sold) '12 ZL1 A6 Black 10.52@131 1.55 60' 2:13 VIR Full (sold) |
|
|
|
|
|
|
|
|
Post Reply
|
|
|
