Front tire fender gap fixed for 2018 with pics! - Page 10

bobby35ny · 08-17-2017, 01:08 PM

Quote:

Originally Posted by KLR ZL1

Ok, I just measured mine and the fronts are 2 7/8" and the rears are 1 7/8". So is that correct or not? Build date end of March.

Those numbers seem off to me, make sure car is level and you measure centerline using the spindle as center.

A good corrected number is 2 1/2 all around.

-bobby

neenja_jenkins · 08-17-2017, 03:09 PM

What exactly do I need to say to the people at the stealership to get this done?
My car was in for an oil change and I mentioned it to them and they gave me a run-around. Basically "we can't do anything unless you're complaining that something is wrong", to which I said "my front end sits considerably higher than my rear which seems odd", but continued to get the run around about "warranty" and this isn't covered, etc.

FringBirdAloha · 08-17-2017, 03:15 PM

Quote:

Originally Posted by neenja_jenkins

What exactly do I need to say to the people at the stealership to get this done?
My car was in for an oil change and I mentioned it to them and they gave me a run-around. Basically "we can't do anything unless you're complaining that something is wrong", to which I said "my front end sits considerably higher than my rear which seems odd", but continued to get the run around about "warranty" and this isn't covered, etc.

Have them type in the bulletin number. It won’t show if they search the database manually or use keyword search like “trim height”. It took about 8 minutes of my service advisor typing in the bulletin number in different formats until the computer picked it up. Don’t let up! I wouldn’t leave my advisors office I kept insisting and finally I was justified and it popped up.

KLR ZL1 · 08-17-2017, 03:24 PM

Quote:

Originally Posted by bobby35ny

Those numbers seem off to me, make sure car is level and you measure centerline using the spindle as center.

A good corrected number is 2 1/2 all around.

-bobby

Car is as level as possible. measured center of arch of fender to the same line as OP.

bobby35ny · 08-17-2017, 04:16 PM

Quote:

Originally Posted by KLR ZL1

Car is as level as possible. measured center of arch of fender to the same line as OP.

Look at my SIG, you can see how high I am in the front, yours look like that?
-bobby

KLR ZL1 · 08-17-2017, 05:36 PM

Quote:

Originally Posted by bobby35ny

Look at my SIG, you can see how high I am in the front, yours look like that?
-bobby

Lets compare total height from ground to center of wheel arch. I cant tell crap from just looking at a pic. LOL. Mine is 28" with about 32 PSI in the front.

bobby35ny · 08-17-2017, 07:28 PM

Quote:

Originally Posted by KLR ZL1

Lets compare total height from ground to center of wheel arch. I cant tell crap from just looking at a pic. LOL. Mine is 28" with about 32 PSI in the front.

I'm 28 3/8 with 34 PSI and mine got approved for new springs. They came in today, appt is for Tuesday.
-Bobby

FASTNUF · 08-17-2017, 09:56 PM

Pardon me if I missed if this is for only coupes, but my new 2017 ZL1 Vert with build date of 5/17 is 27 & 7/8" front & back from level garage floor to wheel arch, however using the tire line to wheel arch, front is 2 & 1/2" / rear is 2 & 1/4".

After my 2016 Z06 rubbed on my driveway incline and this car does not, I'm good leaving it alone as it may settle some anyway as I put more miles on the car, only have 471 miles today.

bobby35ny · 08-17-2017, 11:28 PM

Quote:

Originally Posted by FASTNUF

Pardon me if I missed if this is for only coupes, but my new 2017 ZL1 Vert with build date of 5/17 is 27 & 7/8" front & back from level garage floor to wheel arch, however using the tire line to wheel arch, front is 2 & 1/2" / rear is 2 & 1/4".

After my 2016 Z06 rubbed on my driveway incline and this car does not, I'm good leaving it alone as it may settle some anyway as I put more miles on the car, only have 471 miles today.

I don't know about the VERT part, but the 2 1/2 looks like you are fine.
-Bobby

BSR-1 · 08-18-2017, 07:50 PM

Quote:

Originally Posted by Mr. Meh

But, I'm in the same boat.. I don't want that kind of work done on my car for a minor to me cosmetic issue.. Now, if the 1st gen springs represented a structural or stability danger at speed and netted a reduced cornering ability, then sure..

Mine has the taller springs and I've had mine up to 175mph, it was very solid. Didn't feel like it was getting unstable or light in the front at all.

Save

conradsteph · 08-18-2017, 08:39 PM

Same here for the 'Vert. Build date 4/17; front and back from floor to fender is 27 7/8".

Blown355 · 08-18-2017, 10:27 PM

Here's mine. Build date: 4/17. Rear is only about an 1/8 lower than the front. I'm ok with that.

mdmoore23 · 08-26-2017, 10:34 AM

Had to bring this one back. Did any of you get a resolution at the dealer yet?

hawk02 · 08-26-2017, 10:43 AM

Quote:

Originally Posted by mdmoore23

Had to bring this one back. Did any of you get a resolution at the dealer yet?

I have a appointment at the dealer on Monday. I definitely will post before and after photos.

08-18-2017, 10:27 PM	#138
Blown355 Drives: 2017 ZL1 A10 Join Date: Sep 2009 Location: Austin TX Posts: 866	Here's mine. Build date: 4/17. Rear is only about an 1/8 lower than the front. I'm ok with that. Attached Images __________________ 2017 ZL1 A10 Redhot with stripe

08-17-2017, 03:09 PM	#128
neenja_jenkins Drives: 2017 Camaro ZL1 Join Date: Aug 2014 Location: Dallas Posts: 145	What exactly do I need to say to the people at the stealership to get this done? My car was in for an oil change and I mentioned it to them and they gave me a run-around. Basically "we can't do anything unless you're complaining that something is wrong", to which I said "my front end sits considerably higher than my rear which seems odd", but continued to get the run around about "warranty" and this isn't covered, etc.

08-17-2017, 09:56 PM	#134
FASTNUF Drives: 2017 ZL1 A10 White Vert Join Date: Aug 2017 Location: Katy Tx Posts: 151	Pardon me if I missed if this is for only coupes, but my new 2017 ZL1 Vert with build date of 5/17 is 27 & 7/8" front & back from level garage floor to wheel arch, however using the tire line to wheel arch, front is 2 & 1/2" / rear is 2 & 1/4". After my 2016 Z06 rubbed on my driveway incline and this car does not, I'm good leaving it alone as it may settle some anyway as I put more miles on the car, only have 471 miles today.

08-18-2017, 08:39 PM	#137
conradsteph Drives: 2017 ZL1 Vert Arctic Blue Join Date: Mar 2017 Location: Phoenix, AZ Posts: 73	Same here for the 'Vert. Build date 4/17; front and back from floor to fender is 27 7/8".

08-26-2017, 10:34 AM	#139
mdmoore23 Drives: 2017 ZL1 Join Date: Jun 2012 Location: Graniteville,SC Posts: 646	Had to bring this one back. Did any of you get a resolution at the dealer yet?

User Name		Remember Me?
Password