[cncmotors]

I have installed Maggie HB and got custom tune from uncle, Ted.
I just solved installation issue that mentioned in the other thread. Big thanks to all supporters.

My vehicle is the first Camaro SS with Maggie in South Korea. It means that I could not get any helps on install except the install manual.

I tried to run the car today but I got error code as a pic I attached.

I need another help on this issue..



17' Camaro SS A8 non-npp
Has mods below:

Maggie HB with Intercoolered
ARH 1-7/8 Full Exhaust
Roto-Fab CAI

[SSDan]

I'm stating the obvious I know but if you mean Ted Jannetty when you say Uncle Ted then and if he created a custom tune for you then by all means go straight to him with this error code. I am sure the help he will give you will be the best solution.

[cncmotors]

Originally Posted by SSDan

I'm stating the obvious I know but if you mean Ted Jannetty when you say Uncle Ted then and if he created a custom tune for you then by all means go straight to him with this error code. I am sure the help he will give you will be the best solution.

I believe that Ted's tune has no broblem with it. He sure helps me for this issue but I just wanna share this trouble happening then others can have info when they get sams trouble. I hope they won't need it but

Thank you!

[JANNETTYRACING]

Originally Posted by cncmotors

I have installed Maggie HB and got custom tune from uncle, Ted.
I just solved installation issue that mentioned in the other thread. Big thanks to all supporters.

My vehicle is the first Camaro SS with Maggie in South Korea. It means that I could not get any helps on install except the install manual.

I tried to run the car today but I got error code as a pic I attached.

I need another help on this issue..



17' Camaro SS A8 non-npp
Has mods below:

Maggie HB with Intercoolered
ARH 1-7/8 Full Exhaust
Roto-Fab CAI

As stated in the other 2 threads.

The first 2 codes are caused by not installing the supplied IAT sensor harness.

The next 3 are due to likely a coil connection at Number indicated #2.

The last 5 are caused by the removal of the Exhaust valves in the exhaust system.

Ted.

[cncmotors]

Originally Posted by JANNETTYRACING

As stated in the other 2 threads.

The first 2 codes are caused by not installing the supplied IAT sensor harness.

The next 3 are due to likely a coil connection at Number indicated #2.

The last 5 are caused by the removal of the Exhaust valves in the exhaust system.

Ted.

Thank you, Ted.

I don't know why first two codes still come up after installing IAT harness correctly.

I will let you know what comes up after replace #2's plug and coils to new. I hope they diaapear after replacing them.

I sent an email that request purchasing the module

Thanks again for your supports.

Jay

[JANNETTYRACING]

Originally Posted by cncmotors

Thank you, Ted.

I don't know why first two codes still come up after installing IAT harness correctly.

I will let you know what comes up after replace #2's plug and coils to new. I hope they diaapear after replacing them.

I sent an email that request purchasing the module

Thanks again for your supports.

Jay

One of the problems with these cars is you need a Dealer MDI to clear them or you have to wait several key cycles before they clear themselves after the repair.

You can not disconnect any sensors with the battery connected or it will set a permanent code.

For example, if you unplug the MAF it will set a code.

Ted.

[cncmotors]

Originally Posted by JANNETTYRACING

One of the problems with these cars is you need a Dealer MDI to clear them or you have to wait several key cycles before they clear themselves after the repair.

You can not disconnect any sensors with the battery connected or it will set a permanent code.

For example, if you unplug the MAF it will set a code.

Ted.

Copied! Thank you!!

[cncmotors]

I just replaced plug and coil on cylinder2 but still have same problem with it. I also forgot mentioning that "Service Stabilitrak" warning sign comes on.
Anybody has same trouble with Maggie?? I am pretty sure that installation was correctly done..