02-18-2016, 03:22 PM | #1 |
Drives: 1994 1LE / 2006 Z51 Corvette Join Date: Jul 2009
Location: Plano, TX
Posts: 2,829
|
*Sneak peak* LG Motorsports 2016 Camaro SS Exhaust
Finished the first prototype sets today, going on the dyno for testing next
LG Motorsports Super Pro 1 7/8" long tube headers 3" high flow cats X pipe and full 3" mid section LG 3" mufflers No NPP Last edited by Anthony @ LG Motorsports; 02-18-2016 at 03:50 PM. |
02-18-2016, 03:35 PM | #2 |
Drives: 18 Silverado 1500 Join Date: Dec 2015
Location: Bradenton, FL
Posts: 1,721
|
Using the NPP exhaust? If so, what is needed for the install?
__________________
16 Red Hot 2SS A8: NPP, CAI Cold air, Ported TB, Fasterproms Ported intake, E85 flex, Formatto tuned. 11.80@118 with 1.92 60' (600-700 DA) on stock run flats.
|
02-18-2016, 03:47 PM | #3 |
Lethal Camaro
Drives: 16 2SS, 71 Std, Suburban RTS Join Date: Jun 2013
Location: Temecula, CA
Posts: 3,855
|
The note sounds very sharp, is this just a axle back setup or full from the tri-y manifolds back?
__________________
|
02-18-2016, 03:49 PM | #4 | |
Drives: 1994 1LE / 2006 Z51 Corvette Join Date: Jul 2009
Location: Plano, TX
Posts: 2,829
|
Quote:
This design currently has no valves, AFM or otherwise on it. |
|
02-18-2016, 03:56 PM | #5 | |
Lethal Camaro
Drives: 16 2SS, 71 Std, Suburban RTS Join Date: Jun 2013
Location: Temecula, CA
Posts: 3,855
|
Quote:
Even the little bit of idling we can hear at the start sounds tame. and sorry... I 100% missed the details you posted under the video, though that was a signature
__________________
|
|
02-18-2016, 03:58 PM | #6 |
Drives: 1994 1LE / 2006 Z51 Corvette Join Date: Jul 2009
Location: Plano, TX
Posts: 2,829
|
|
02-18-2016, 03:59 PM | #7 | |
Drives: 1994 1LE / 2006 Z51 Corvette Join Date: Jul 2009
Location: Plano, TX
Posts: 2,829
|
Quote:
|
|
02-18-2016, 04:23 PM | #8 |
Drives: Car Join Date: Jun 2010
Location: Place
Posts: 3,361
|
If you're not using NPP on that, then for those of us w/o NPP and want muffler only. Will you supply the dual/dual lower valance panel or is that something we'd need to source from another supplier?
|
02-18-2016, 04:53 PM | #9 | |
Drives: 1994 1LE / 2006 Z51 Corvette Join Date: Jul 2009
Location: Plano, TX
Posts: 2,829
|
Quote:
Should we make them all 4 tip and sell a GM lower panel to go with it (like Ford is doing with the Mustang GT exhaust to mimic the GT350) or have a single tip and a dual tip muffler so it would fit both cars with no changes? |
|
02-18-2016, 05:09 PM | #10 | |
Drives: Chevys at the limit Join Date: Nov 2010
Location: SLC, UT
Posts: 9,621
|
Quote:
Jared Royce 801.545.4215 |
|
02-18-2016, 05:22 PM | #11 | |
Drives: pbm Join Date: Jul 2014
Location: United States
Posts: 25
|
Quote:
BTW, are those rims your 5th gen 1LEish replica? Look nice in there... |
|
02-18-2016, 05:27 PM | #12 |
Drives: 1994 1LE / 2006 Z51 Corvette Join Date: Jul 2009
Location: Plano, TX
Posts: 2,829
|
|
02-18-2016, 05:41 PM | #13 |
Drives: pbm Join Date: Jul 2014
Location: United States
Posts: 25
|
|
02-18-2016, 05:43 PM | #14 |
Drives: 1994 1LE / 2006 Z51 Corvette Join Date: Jul 2009
Location: Plano, TX
Posts: 2,829
|
|
|
|
Post Reply
|
|
|