[Joshinator99]

Originally Posted by Camby

Got my ACS skirts.





Sent from my iPhone using Tapatalk

Looking good!

[SSShark]

Originally Posted by Camby

Got my ACS skirts.






Sent from my iPhone using Tapatalk

Looking sharp Which Conti's are you sporting? The tread looks a little different than the Sport 02's?

[willzilla]

Installed the BMR billet aluminum sway bar mounts & Delrin bushings onto both the front and rear BMR adjustable sway bars. Video comparing the included formed steel saddle mounts and poly bushings that BMR includes with their sway bars (that some members on here had issues with) and their upgraded billet mounts and Delrin bushings:



A couple photos:




Now I just need to reinstall the back half of my exhaust, the front under tray stuff, and one of my replacement carbon fiber side skirts and I can finally go get an alignment!

[christianchevell]

I actually got a little camera cause my google phone sucks and its not exactly easy to get pics from, and I posted to a guys zl1 thread who has a desire for a lots of my same parts
so I could link them on here, I am usually busy busy, not my first built Camaro, Have a great day!

2021 Chevrolet Camaro ZL1 OPTIONS: Wild Cherry Paint, Exposed Carbon Fiber Weave Heat Extractor, Performance Date Recorder, Navigation, Sun Roof, Red Seat belts, Automatic 10 Speed, All Weather Floor Mats. With Magnetorheological Shocks.

Mods:Red Carbon Fiber Interior,Clear Bra, GM Side Spear Stripes, Aftermarket 1LE 20" Wheels, Rear Wing Spoiler, Front Down Planes, Borla ATAK Cat Back exhaust with Dual Mode Exhaust, Drive Shaft Shop 1000 HP Drive line. Speed Engineering Three Piece Intercooler Set, Radiator Screen,Detachable License Plate, American Muscle Rear Louvers, Wheel Rock Guards, Tint, Velossatech Ram Air Scoop.

BMR Suspension: Chassis Brace Front Cradle, Drive Shaft Safety Loop, Tunnel Brace, Tubular Motor Mounts, Rear Cradle Bushings Lock Out Kit, Control Arms, Toe Rods, Lower and Upper Trailing Arms, Lower Control Arms, Sway Bar End Links, Continental Extremne Contact Tires.

Engine: BTR Stage Two Supercharger Cam : 223/24x 114 LSA ,.639/.639, +38% Fuel Lobe, .660 lift Dual Springs,Seals/Locks, Hardened Pushrods, Smith Bro's Trunnion Bushings, LS7 Lifters, Late Model Engines AFM/DOD delete kit Billet Timing Cover, Gear,& Billet Tensioner, Katech C5R Timing Chain, Katech Billet Oil Pump, Magnuson 2650 Supercharger, DSX Billet Powdercoated Lid 32% larger Volume than Magnuson, Speed Engineering Billet Valve Covers, Nick Williams 103 MM Throttle Body, Rotofab Big Gulp Intake, Lingenfelter Low Side Check Valve, Lingenfelter Boostapump, Elite Engineering E-2X Ultra Catch Can, Texas Speed 1 7/8 Stainless Headers with High Flow Cats, ATI SuperDamper with ATI 8% Overdrive Pulley #906106, Griptec 90MM Upper Pulley, Gates Belt, NGK TR7IX plugs, Granetelli Malevolent 85K coils and Zero Ohm Wires.

Tru Fiber Carbon Fiber Hood Liner, American Car Craft LED Wiper Cowl, And Front Header Radiator Cover, Varied Stainless and Aluminum Covers.

Cammed and Dyno Tuned at Rated R Performance San Anonio Texas, Results: 770 RWHP 769 RWTQ Dyno on 92 Octane Fuel from Oregon. Thats over 900 Crank for an automatic. Supporting Mods at VT Auto Oregon State Pen.
AT 13 lbs Boost......

hey figured out how to imbed again been years..LOL



I think I will throw in some of my 13 and my 71 monte and 73 chevelle even ..LOL Have a good day !!!!




Yup Old hot rodder here ...









And Silverton oregon of Joe Dirt fame..LOL

[arpad_m]

Originally Posted by christianchevell

I actually got a little camera cause my google phone sucks and its not exactly easy to get pics from, and I posted to a guys zl1 thread who has a desire for a lots of my same parts
so I could link them on here, I am usually busy busy, not my first built Camaro, Have a great day!

2021 Chevrolet Camaro ZL1 OPTIONS: Wild Cherry Paint, Exposed Carbon Fiber Weave Heat Extractor, Performance Date Recorder, Navigation, Sun Roof, Red Seat belts, Automatic 10 Speed, All Weather Floor Mats. With Magnetorheological Shocks.

Mods:Red Carbon Fiber Interior,Clear Bra, GM Side Spear Stripes, Aftermarket 1LE 20" Wheels, Rear Wing Spoiler, Front Down Planes, Borla ATAK Cat Back exhaust with Dual Mode Exhaust, Drive Shaft Shop 1000 HP Drive line. Speed Engineering Three Piece Intercooler Set, Radiator Screen,Detachable License Plate, American Muscle Rear Louvers, Wheel Rock Guards, Tint, Velossatech Ram Air Scoop.

BMR Suspension: Chassis Brace Front Cradle, Drive Shaft Safety Loop, Tunnel Brace, Tubular Motor Mounts, Rear Cradle Bushings Lock Out Kit, Control Arms, Toe Rods, Lower and Upper Trailing Arms, Lower Control Arms, Sway Bar End Links, Continental Extremne Contact Tires.

Engine: BTR Stage Two Supercharger Cam : 223/24x 114 LSA ,.639/.639, +38% Fuel Lobe, .660 lift Dual Springs,Seals/Locks, Hardened Pushrods, Smith Bro's Trunnion Bushings, LS7 Lifters, Late Model Engines AFM/DOD delete kit Billet Timing Cover, Gear,& Billet Tensioner, Katech C5R Timing Chain, Katech Billet Oil Pump, Magnuson 2650 Supercharger, DSX Billet Powdercoated Lid 32% larger Volume than Magnuson, Speed Engineering Billet Valve Covers, Nick Williams 103 MM Throttle Body, Rotofab Big Gulp Intake, Lingenfelter Low Side Check Valve, Lingenfelter Boostapump, Elite Engineering E-2X Ultra Catch Can, Texas Speed 1 7/8 Stainless Headers with High Flow Cats, ATI SuperDamper with ATI 8% Overdrive Pulley #906106, Griptec 90MM Upper Pulley, Gates Belt, NGK TR7IX plugs, Granetelli Malevolent 85K coils and Zero Ohm Wires.

Tru Fiber Carbon Fiber Hood Liner, American Car Craft LED Wiper Cowl, And Front Header Radiator Cover, Varied Stainless and Aluminum Covers.

Cammed and Dyno Tuned at Rated R Performance San Anonio Texas, Results: 770 RWHP 769 RWTQ Dyno on 92 Octane Fuel from Oregon. Thats over 900 Crank for an automatic. Supporting Mods at VT Auto Oregon State Pen.
AT 13 lbs Boost......

hey figured out how to imbed again been years..LOL



I think I will throw in some of my 13 and my 71 monte and 73 chevelle even ..LOL Have a good day !!!!


Yup Old hot rodder here ...

You've had some beautiful cars, and this new ZL1 is definitely no slouch Congrats and welcome back!

Quick question, what driveshaft did you get from DSS, chromoly, carbon fiber, or...? Did that cause any extra vibration, or is it as seamless as the stock unit?

[christianchevell]

Chrome moly and no extra vibes...... Going for the rear axles some day soon ...

[JSH]

Filled it up with race gas and went for a spin

[willzilla]

Finally finished up the BMR Suspension installs, got the wheels back on, the back portion of the exhaust back on, and everything buttoned up. Hard to believe I initially put the car up on my QuickJack 9 MONTHS ago! Lol. A million other things came up and the car sat way longer than I had planned when I began :-/



After 9 months there was a nice layer of dust coating the entire car so I had to finally give it a good wash.



Turned out nice even though wasn't a hardcore detail job.. still need to hit it with some ceramic boost wipe down and wire cleaning.. touch up the interior.. and wipe down the engine bay. Also still need to install replacement Trufiber carbon fiber side skirt for the passenger side and get an alignment done!

[DamonZ28]

Installed some smoked-out blue side marker lights, just for pics. Then I removed them and installed smoked-out side marker lights with two lines of LED lights, instead of just one. The blue ones aren't street legal, of course, and I'm not looking for hassles.

[tortilla-flats]

Did a test pack in preparation for my first trip to the races this coming weekend. Got everything to fit in the trunk with a bit of room to spare.

First trip is running completely 100% stock, so there were a few things left off the list.

[clg82]

Originally Posted by willzilla

Finally finished up the BMR Suspension installs, got the wheels back on, the back portion of the exhaust back on, and everything buttoned up. Hard to believe I initially put the car up on my QuickJack 9 MONTHS ago! Lol. A million other things came up and the car sat way longer than I had planned when I began :-/



After 9 months there was a nice layer of dust coating the entire car so I had to finally give it a good wash.



Turned out nice even though wasn't a hardcore detail job.. still need to hit it with some ceramic boost wipe down and wire cleaning.. touch up the interior.. and wipe down the engine bay. Also still need to install replacement Trufiber carbon fiber side skirt for the passenger side and get an alignment done!

could have been worse, you could have had the BMR stuff sitting on the bench for 4 years

[willzilla]

Originally Posted by clg82

could have been worse, you could have had the BMR stuff sitting on the bench for 4 years

Haha, yeah.. I think my BMR stuff "only" sat on my bench for 2 years or so

[SS_Aylem,]

I washed and drove it.

[sklippi2018]

Found this recall for my car and called the dealership. No remedy yet but be looking out for your letter from GM.

Side note: shouldn't you have the remedy ready before you televise a recall? I'm just a peasant so what do I know?

https://www.nhtsa.gov/recalls?gad_so...B&gclsrc=aw.ds