You are browsing camaro6 
10-31-2023, 09:12 AM
|
#1 |
 Drives: chevrolet camaro Join Date: Aug 2019
Location: MD
Posts: 35
|
Valve Covers
hello All
I'm looking for a set of valve covers to dress the engine up a bit on my 21 ZL1 but I also want to be able to use the factory connections for the PCV system. any suggestions or any pics with them installed |
|
|
|
10-31-2023, 09:45 AM
|
#2 |
    
Drives: 2023 ZL1 Join Date: Dec 2022
Location: Columbus, Ohio
Posts: 1,287
|
Most valve cover manufactures can utilize standard NA fittings if you get to correct size and angle etc. Keep in mind all valve covers are not built the same. I just went through this and had several issues until I found the right combination of things that correct my issues after I replaced my valve covers. Keep in mind, stock valve covers for the Camaro (ZL1 in my case) have a baffle built into the, and some aftermarket valve covers have them as well, but some do not. Attached is a cutaway of a stock ZL! valve cover that shows the built in baffle.
__________________
Katech Track Day CAM 38%•BTR Dual Valve Springs•Johnson Lifters•Trend 3/8 Chromoly Pushrods• VVT Del•CNC Heads•AFM Delete• C5-R Timing Chain•Katech Oil Pump•Katech 112mm•Maggie 2650 3.25” Upper/ATI SD w/10.32” +20%•10 Rib Belt•RFBG•FI IC Stage 2•THPSI Port w/875cc Inj•Katech Dual Fuel Pump•DSX Aux Pump•SW 2" Headers w/Legend NPP•GESI UHO 4.5" CATs•Brisk RR14S Plugs•BMR Motor Mounts•BMR Cradle Lockout &Bushings Kit•BMR Rear Suspension & 15" Conversion•DSS 1pc DS•RPM 6-Point Roll Cage•10lb FireSense+ w/4Fire SFI 17.1 Fire Sys•Weld Forged Vitesse Rear 17x10 Beadlocks-Front 18x6•Unlocked TCM
 |
|
|
|
|
10-31-2023, 09:58 AM
|
#3 |
|
Drives: chevrolet camaro Join Date: Aug 2019
Location: MD
Posts: 35
|
which valve covers did you eventually settle on
|
|
|
|
|
10-31-2023, 10:06 AM
|
#4 |
|
Having FUN in the SUN...
 
Drives: 2022 M6 ZL1 1LE Join Date: Jan 2022
Location: San Diego CA
Posts: 2,190
|
These are the Katech Cast Valve Covers... I think they are the best looking on the market, but they require the following...
1. Coil Relocation Kit (no brainer) 2. Re-Plumb PCV Hoses as the connector locations change. 3. Install a MM Wild CC (also a no brainer) IMO 4. Using a restriction fitting on the clean side of the CC as the Katech cover have no baffling. In short, this is not an easy transformation for some... but for me, it was 100% worth it!
__________________
2022 M6 ZLE: GMS Stage.III KONG X.PORT Package + DMS Lid + GMS Rear Bumper Belly Pan + GMS Hood Bracket + GMS Flex Fuel Package + MONSTER Triple S Clutch + XDI.50% Injectors + CLICK FOR BUILD LIST or www.GRIFFIN-MOTORSPORTS.com = 915rwhp 850rwtq + E60 + 15psi
|
|
|
|
|
10-31-2023, 10:30 AM
|
#5 |
|
Drives: chevrolet camaro Join Date: Aug 2019
Location: MD
Posts: 35
|
That's some awesome work!! I saw those valve covers but every site i went to said they were for the 5th gen Camaro, but i see they fit the 6th gen. on the re plumbing were you able to use the factory connectors and connection points. i have elite engineering catch can installed already. i also have that same DSX SC lid
|
|
|
|
|
10-31-2023, 10:37 AM
|
#6 |
|
Moderator
Drives: 2017 Camaro 2SS A8 Join Date: Aug 2018
Location: New Ipswich NH
Posts: 6,350
|
Much better running the TooHighPSI version in my opinion. Sexy AF and OEM level oil baffling. I would not buy a valve cover without proper oil baffling or you end up having to significantly reduce catch can flow which is counterproductive.
https://toohighpsi.com/products/vind...t-valve-covers
__________________
2017 Chevy Camaro 2SS A8 Whipple 3.0, Mast Black Label heads, ATI 8L90, Fore triple in-tank pumps, 112mm TB, LPE +52% injectors & BB HPFP, TooHighPSI/Katech port injection, 15” conversion 1066 WHP STD/1027 SAE, 9.10@152.5 (new times coming)
|
|
|
|
|
10-31-2023, 10:56 AM
|
#7 |
|
Drives: chevrolet camaro Join Date: Aug 2019
Location: MD
Posts: 35
|
those are the best i've seen yet. and i like that they offer two types of connections for PCV system
|
|
|
|
|
10-31-2023, 11:05 AM
|
#8 | |
      
Drives: '20 ZLE Join Date: Jun 2020
Location: Mile High
Posts: 4,195
|
Quote:
__________________
2020 ZL1LE A10.
LME LT4 390 short block, LME CID Heads, Kong E2650, FBO. 15" conversion, MT ET Street R 325/15. 100 octane: 1045hp/1055tq. 100 octane + Meth (1x10+): 1117 hp/1067 tq |
|
|
|
|
|
10-31-2023, 12:16 PM
|
#9 | |
|
Having FUN in the SUN...
Drives: 2022 M6 ZL1 1LE Join Date: Jan 2022
Location: San Diego CA
Posts: 2,190
|
Quote:
Those look bad ass also!
__________________
2022 M6 ZLE: GMS Stage.III KONG X.PORT Package + DMS Lid + GMS Rear Bumper Belly Pan + GMS Hood Bracket + GMS Flex Fuel Package + MONSTER Triple S Clutch + XDI.50% Injectors + CLICK FOR BUILD LIST or www.GRIFFIN-MOTORSPORTS.com = 915rwhp 850rwtq + E60 + 15psi
|
|
|
|
|
|
10-31-2023, 12:42 PM
|
#10 | |
|
Super Stock
Drives: Chevrolet Camaro ZL1 Join Date: May 2022
Location: Concordia
Posts: 1,004
|
Quote:
__________________
2017 Red Hot ZL1 A10 - Apex ARC-8's, 305/ 325 PS4's, DSX 9.06 12% lower, Griptec OE upper, NGK HR7 Ruthenium plugs, Nostrum 25+ injectors, XDI Goliath HPFP, Katech dual in tank LPFP, Katech oil pump, LME tensioner, DOD delete, LT1 big fuel cam, Jokerz ported blower, MPI lid, GMS hood extractor bracket, Granatelli SS plug wires, Cordes LTR reservoir, DMS T-stat housing, 186* LS3 T-stat, Borla X pipe, Black Widow Angry Housewife/ Corsa NPP mufflers, BMR engine mounts, Banks iDash, Lithium Battery, AEM X- Series, HP Tuners, E85, 16.5 psi
758 HP/ 804 TQ  |
|
|
|
|
|
10-31-2023, 01:11 PM
|
#11 | |
|
Drives: '20 ZLE Join Date: Jun 2020
Location: Mile High
Posts: 4,195
|
Quote:
__________________
2020 ZL1LE A10.
LME LT4 390 short block, LME CID Heads, Kong E2650, FBO. 15" conversion, MT ET Street R 325/15. 100 octane: 1045hp/1055tq. 100 octane + Meth (1x10+): 1117 hp/1067 tq |
|
|
|
|
|
10-31-2023, 01:18 PM
|
#12 |
|
Drives: chevrolet camaro Join Date: Aug 2019
Location: MD
Posts: 35
|
those supercharged covers are sweet!!. you have a link to them
|
|
|
|
|
10-31-2023, 02:05 PM
|
#13 |
|
Nightmare
Drives: Your mom crazy in bed Join Date: Mar 2011
Location: Naptown
Posts: 2,442
|
https://www.wegnerautomotive.com/custom-engraving-4/
These are pretty sweet - seen em for an LS build, was considering them for my SS. Pricey, but I think they really look fantastic..
__________________
 |
|
|
|
|
10-31-2023, 02:15 PM
|
#14 | |
|
Drives: 2023 ZL1 Join Date: Dec 2022
Location: Columbus, Ohio
Posts: 1,287
|
Quote:
https://www.camaro6.com/forums/showthread.php?t=611982 But, I also added a catch can, this is where my issue showed itself. But I'm not sure the issue was only related to adding the valve covers with no baffles and adding the catch can too. I did get the issue resolved with a lot of help from vendors and members here giving advice. My selection was between the Katech's valve covers I already installed or the DSX Billet valve covers that have baffles. https://dsxtuning.com/products/dsx-b...33206558752848 Good luck !
__________________
Katech Track Day CAM 38%•BTR Dual Valve Springs•Johnson Lifters•Trend 3/8 Chromoly Pushrods• VVT Del•CNC Heads•AFM Delete• C5-R Timing Chain•Katech Oil Pump•Katech 112mm•Maggie 2650 3.25” Upper/ATI SD w/10.32” +20%•10 Rib Belt•RFBG•FI IC Stage 2•THPSI Port w/875cc Inj•Katech Dual Fuel Pump•DSX Aux Pump•SW 2" Headers w/Legend NPP•GESI UHO 4.5" CATs•Brisk RR14S Plugs•BMR Motor Mounts•BMR Cradle Lockout &Bushings Kit•BMR Rear Suspension & 15" Conversion•DSS 1pc DS•RPM 6-Point Roll Cage•10lb FireSense+ w/4Fire SFI 17.1 Fire Sys•Weld Forged Vitesse Rear 17x10 Beadlocks-Front 18x6•Unlocked TCM
|
|
|
|
|
|
|
|
|
|
Post Reply
|
|
|
