04-29-2023, 07:24 AM | #1 |
Drives: 2020 ZL1 A10; Shadow Gray Metallic Join Date: Sep 2020
Location: Chicago
Posts: 179
|
Driver Side Hood Gap
The past weekend, I saw some ZLEs with rotofabs and noticed that their rotofab seals were completely smashed. My rotofab seal looks brand new, no compression on it. Took a look at my hood alignment, and sure enough it wasn't aligned.
I've read the posts about a hood gap and hood alignment and tried to fix it myself. This is the best I could get my driver side hood gap to look like. (Ignore the water spots, this was after 4 track days ) I've tried all combinations of loosening and tightening the torx bolts. I've tried all combinations of adjusting the rubber nubs. I've tried all combinations of adjusting the hood latch, and I'm not sure what else to improve it. What worked best was raising the passenger side hood latch as far up as it would go, lowering the driver side hood latch as far down as it would go, raising the leftmost passenger rubber nub as far as it would go, loosening the passenger bolt, and tightening the driver side torx bolt. Any other thoughts or recommendations? I have the bumper to bumper warranty until July, but the dealer is an hour away and I'm 50/50 if they'll even fix it under warranty (ZLE aero installed and rotofab CAI) |
05-01-2023, 10:08 AM | #2 |
Drives: 2020 Camaro ZL1 Join Date: Oct 2020
Location: Fort Worth, Texas
Posts: 1,174
|
Mine looks the same way, I think it's common to ZL1s.
__________________
2020 ZL1 A10 Shadow Gray Metallic
Magnuson Magnum DI TVS2650R| Mamo Throttle Body V2| RotoFab Intake| AWE Touring Catback Exhaust| TCM Tune| Tune| Eibach Pro| BMR Rear Cradle Lockout| PPF| Ceramic| BCForged HCS21 |
05-01-2023, 10:17 AM | #3 |
Drives: 2016 1SS NFG A8 Join Date: Aug 2017
Location: 46804
Posts: 6,827
|
Need to loosen the hood mounts back by the cowl and move the back of the hood towards the driver side.
__________________
2016 NFG 1SS A8
Options-2SS Leather/NPP Perf. mods-Whipple 2.9/Fuel System/Flex Fuel/103mm TB/Rotofab Big Gulp/Cat Deletes/Corsa NPP Per. times- 10.5 @ 137 w/ 1.8 60ft Full weight on 20's 1200DA |
05-01-2023, 10:56 AM | #4 |
Drives: 2020 ZL1 A10; Shadow Gray Metallic Join Date: Sep 2020
Location: Chicago
Posts: 179
|
|
05-01-2023, 11:07 AM | #5 |
Drives: 2016 1SS NFG A8 Join Date: Aug 2017
Location: 46804
Posts: 6,827
|
where the hood bolts to the hinges.
__________________
2016 NFG 1SS A8
Options-2SS Leather/NPP Perf. mods-Whipple 2.9/Fuel System/Flex Fuel/103mm TB/Rotofab Big Gulp/Cat Deletes/Corsa NPP Per. times- 10.5 @ 137 w/ 1.8 60ft Full weight on 20's 1200DA |
05-01-2023, 12:57 PM | #6 |
Drives: 2023 ZL1 - Modified All Bolt On's Join Date: Dec 2022
Location: Columbus, Ohio
Posts: 588
|
On my (I showed this on my post) My hood gap was larger on the drivers side vs the passenger side. found out it was due to the under hood scoop rain deflector making contact the the round air intake tube of the roto-fab. Once I shave a small amount of the rain deflector off, my hood closed properly and equally on both the passenger and drivers side.
|
05-01-2023, 01:17 PM | #7 | |
Drives: 2020 ZL1 A10; Shadow Gray Metallic Join Date: Sep 2020
Location: Chicago
Posts: 179
|
Quote:
|
|
05-01-2023, 01:19 PM | #8 | |
Drives: 2018 Camaro 2SS A8 Join Date: Jul 2017
Location: East Tennessee
Posts: 11,696
|
Quote:
__________________
2018 Camaro 2SS — G7E MX0 NPP F55 IO6
735 rwhp | 665 rwtq Magnuson TVS 2300 80mm pulley | Kooks 1 7/8" LT headers | JRE smooth idle terminator cam | LT4 FS & injectors | TSP forged pistons & rods JMS PowerMAX | DSX flex fuel kit | Roto-Fab CAI | Soler 95mm LT5 TB | 1LE wheels | 1LE brakes | BMR rear cradle lockout | JRE custom tune 1100 - 1/30/18 | 2000 - 1/31/18 3000 - 2/06/18 TPW 2/26/18 3400 - 2/19/18 | 3800 - 2/26/18 4300 - 2/27/18 | 4B00 - 3/01/18 4200 - 3/05/18 | 4800 - 3/14/18 5000 - 3/16/18 | 6000 - 3/19/18 |
|
05-01-2023, 02:29 PM | #9 |
Drives: 2020 ZL1 A10; Shadow Gray Metallic Join Date: Sep 2020
Location: Chicago
Posts: 179
|
I had seen that image but couldn't tell what it was referencing by the 4 hood hinge nuts. 2 hinge nuts by the hydraulic arms, got it.
|
05-01-2023, 03:01 PM | #10 |
Drives: Canadian 2019 BLACK ZL1 Join Date: Feb 2020
Location: Bourges (France)
Posts: 412
|
Mine is not centered on the Carbon fiber part…
|
05-01-2023, 03:02 PM | #11 | |
Drives: 2023 ZL1 - Modified All Bolt On's Join Date: Dec 2022
Location: Columbus, Ohio
Posts: 588
|
Quote:
Here is my post talking about this: https://www.camaro6.com/forums/showp...4&postcount=93 |
|
05-01-2023, 03:13 PM | #12 | |
Drives: 2020 ZL1 A10; Shadow Gray Metallic Join Date: Sep 2020
Location: Chicago
Posts: 179
|
Quote:
|
|
05-01-2023, 03:16 PM | #13 |
Drives: 2020 ZL1 A10; Shadow Gray Metallic Join Date: Sep 2020
Location: Chicago
Posts: 179
|
|
05-01-2023, 07:02 PM | #14 |
Drives: 2017 Camaro ZL1 Coupe Join Date: May 2016
Location: Georgia
Posts: 5,820
|
My ZL1 has a slight driver side gap with the RotoFab but doesn’t have an effect on closing the hood. Mine has been on the car since 2020 so I would say the rubber gasket is compressed enough now.
__________________
ZL1 Coupe, PDR, Exposed carbon fiber hood insert, My Link with Nav, M6 6 speed and Silver Ice Metallic. Mods done: ceramic window tint, GM Accessories Camaro floor mats and Roto-Fab CAI.
|
|
|
Post Reply
|
|
|