You are browsing camaro6 
05-02-2021, 07:56 PM
|
#1 |
 |
Front Splitter Installed
Over the weekend had the chance to put on the gm/ accessory splitter on my 2019 rs camaro and it just makes the front end of car look so much better. Fit and finish of the splitter is perfect like it came from the factory. [ATTACH]1066598[/ATTACH]
|
|
|
|
05-02-2021, 09:24 PM
|
#2 |
 Drives: 2019 1SS M6 Join Date: Feb 2020
Location: Harrisburg,Pa.
Posts: 91
|
Looks great !!
|
|
|
|
05-02-2021, 11:15 PM
|
#3 |
 
|
Wow that does look great. Way better than stock. Well done!
__________________
 #SaveTheManuals |
|
|
|
|
05-03-2021, 06:35 AM
|
#4 |
       
Drives: 2016 Camaro 2SS Hyper Blue Metallic Join Date: May 2020
Location: WI
Posts: 2,623
|
That does look good. I'm normally not a fan of them, but that one does look nice. You say your GM accessory. So you ordered that one right from GM? I might actually consider that one. Do you have the part number?
|
|
|
|
|
05-03-2021, 07:14 AM
|
#5 |
|
Looks great!
|
|
|
|
|
05-03-2021, 08:46 AM
|
#6 |
|
|
Thank's everyone for the nice complement's, the splitter really does make the front of the car look more aggressive. The part number is 84116168 for the 6th generation camaro.
|
|
|
|
|
05-03-2021, 09:08 AM
|
#7 |
 Drives: 2018 Camaro SS vert Join Date: Oct 2020
Location: CT
Posts: 449
|
Looks god!
Whole lot easier to do then expected wasnt it?
__________________
 |
|
|
|
|
05-03-2021, 11:40 AM
|
#8 |
|
|
The hardest part was trying to figure out what I can drive the car up on to get more space under the front, after that no more then 45 minutes. Started with the front center just two screws tighten about half way then peeled away the 3M tape pressed the splitter to the nose put the rest of the screws in then drilled the four holes which were marked and then pop rivet into place. Pretty simple project.
|
|
|
|
|
05-03-2021, 11:58 AM
|
#9 |
Drives: 2018 Camaro ZL1 Join Date: Feb 2019
Location: FL
Posts: 345
|
looks great.
__________________
2018 ZL1 - Daily driver
 2018 Mercedes Benz AMG GTS 2017 C7 Grand Sport - Stage two Edelbrock |
|
|
|
|
05-03-2021, 02:22 PM
|
#10 |
Drives: 2016 Camaro SS Join Date: Jan 2019
Location: Florida
Posts: 305
|
Really completes the look of that bumper.
__________________
2016 Gloss Black Camaro 1SS, A8, MRC, 6-Piston BBK
Whipple, LT4 fueling, AlkyControl, Kooks, Borla, Roto Fab, Mightymouse, aFe, Apex, C7 Carbon, etc...  |
|
|
|
|
05-03-2021, 07:56 PM
|
#11 |
Drives: 2015commemorative vert 2SS Join Date: Oct 2013
Location: northern Indiana
Posts: 949
|
I looked at them all, decided to try the EOS version of this front splitter for less that half the money the OEM version costs. I actually bought the GM version, and shipped it back. Fit was perfect, attached with original screws and a some double sided tape. I did have to paint it, super easy to do.
__________________
2018 ZL1 Bright Yellow, A10, PDR, sunroof, carbon hood, and dash- sold
2020 2SS A10 sunroof..shock and steel special-traded 2015 commemorative vert 2ss |
|
|
|
|
05-03-2021, 08:01 PM
|
#12 | |
 Drives: 2020 Camaro LT1 M6 Join Date: Nov 2020
Location: Miami, FL
Posts: 14
|
Quote:
|
|
|
|
|
|
05-03-2021, 08:09 PM
|
#13 |
|
|
It took me over a year to decide if I wanted to install a splitter or not now I don't know why I waited so long. Thanks everyone for the compliments!
|
|
|
|
|
05-03-2021, 08:20 PM
|
#14 |
|
Drives: 69 Z28 RS 19 2SS Convertible 10 Ava Join Date: Jun 2020
Location: San Antonio Texas
Posts: 52
|
I did the same this weekend, went with the ZL1 addons, splitter and side rails.
I love the fit and look. Diode side markers next. |
|
|
|
|
|
|
|
|
Post Reply
|
|
|
