[Flowtie1]

Uniden with suction cups and diy5 wiring. Couldn't be happier. The uniiden is excellent

[Skyfox16]

Originally Posted by TMD29

For my Redline 360c I modified a Redenso XP visor mount by drilling a hole and bolting the magnet to it. I have the mount attached near the headliner with Velcro black ALFA-LOC fastener tape. I power it using the Gen5 harness plugged into the heater plug in the passenger footwell. The mount has a slight bounce due to the weight of the Redline, but it's not very noticeable. I've used the same ALFA-LOC tape to mount my dashcam and my Uniden R7 without any issues.

Do you have any photos of this setup?

I am attempting to add spacers to my blendmount from my C7 to see if i can get that to work.

I really don't want to use the suction cup because I've had it fall a few times.

[EvilZL]

Originally Posted by MoreSpeed

I had the blendmount for the ZL1 2017. It was not very secure and kept coming loose. I went back to the suction cups on the window.

I just installed my BlendMount with my RedLine 360C last week in my 2018 ZL1 and I have already been on a few rides and mine works great! I will keep an eye on it, but so far it is doing the job its suppose to do

[JSH]

Originally Posted by EvilZL

I just installed my BlendMount with my RedLine 360C last week in my 2018 ZL1 and I have already been on a few rides and mine works great! I will keep an eye on it, but so far it is doing the job its suppose to do

I'm searching for but have not found a totally polite way to describe how unsightly that is sorry

[EvilZL]

Originally Posted by JSH

I'm searching for but have not found a totally polite way to describe how unsightly that is sorry

No worries man it actually looks way bigger than it really is. For some reason it looks huge from my pic's taken with my phone.
Its all good, to each their own

[willzilla]

Is the blend mount available yet for the 2019+ ZL1's with the rearview mirror camera setup? Lol.

[Skyfox16]

Originally Posted by willzilla

Is the blend mount available yet for the 2019+ ZL1's with the rearview mirror camera setup? Lol.

The website says they are developing one, but that mirror has been out since 2019 so I’m not holding my breathe.
I went ahead and just used the suction cup and ordered the gen5 wire kit for now.

[willzilla]

Originally Posted by Skyfox16

The website says they are developing one, but that mirror has been out since 2019 so I’m not holding my breathe.
I went ahead and just used the suction cup and ordered the gen5 wire kit for now.

Yeah, may just do the same.

Was this the harness you picked up?..

https://www.gen5diy.com/collections/...23149496303674

And it is just plug and play on cars with the camera mirror and PDR?

[Skyfox16]

This is the one I got and it plugs in by the passenger footwell then you run the white wire up the front pillar and across the top of the windshield. It works great and I have PDR and the rear view mirror. They have a YouTube video showing the installation under the description on their webpage 👍🏻

[willzilla]

Ok, great, thank you! That's pretty much how I ran my dash cam wiring (well, I went from fuse box in engine bay to a battery pack I mounted in the glove box and then up the same path to up by the rearview mirror).

[Z OH 6]

Originally Posted by willzilla

Is the blend mount available yet for the 2019+ ZL1's with the rearview mirror camera setup? Lol.

Not available yet. I modified one that I had from Hellcat to work for my 2021 ZL1. Its not perfect, but it works just fine until they release one of this year model.

[Z OH 6]

Originally Posted by willzilla

Yeah, may just do the same.

Was this the harness you picked up?..

https://www.gen5diy.com/collections/...23149496303674

And it is just plug and play on cars with the camera mirror and PDR?

Yes, you just have to run the harness around the front of the headliner, down the A-pillar and under the passenger side dash.

[JD64]

just talked to Blend yesterday about a mount for my 19 with the rear camera mirror and they told me it will be the same mount used in the C8. they had a fella coming by their shop yesterday with a c8 for hopefully a final fit after some revisions . if all was good, they should start shipping in 4-6 weeks and they would send out a email to everyone on the waiting list for purchase within the next few weeks. hopefully things go as he thought. just thought id pass on the info

[Z OH 6]

Originally Posted by JD64

just talked to Blend yesterday about a mount for my 19 with the rear camera mirror and they told me it will be the same mount used in the C8. they had a fella coming by their shop yesterday with a c8 for hopefully a final fit after some revisions . if all was good, they should start shipping in 4-6 weeks and they would send out a email to everyone on the waiting list for purchase within the next few weeks. hopefully things go as he thought. just thought id pass on the info

Good to know, I'm already on the mailing list for the C8 mount. I was told by BlendMount that the new part number for the Camaro is BMG-2028.