You are browsing camaro6 
12-28-2020, 09:28 PM
|
#1 |
 Drives: 2016 Camaro Join Date: Aug 2020
Location: Clinton,Ms
Posts: 25
|
O2 sensor locations
Guys i need the distance from the manifold-converter flange to the 1st O2 sensors please. this is for an engine swap using camaro manifolds. if different on each side list them by driver and passenger please and thanks
Last edited by LTCamaro; 12-31-2020 at 06:41 PM. |
|
|
|
12-28-2020, 10:53 PM
|
#2 |
 Drives: 2020 SS 1LE Join Date: Aug 2020
Location: Dallas Tx
Posts: 65
|
Both driver and passenger side are immediately after the manifold/cat flange. Literally about 2-3 inches probably form the flange
|
|
|
|
|
12-28-2020, 11:06 PM
|
#3 |
|
Drives: 2016 Camaro Join Date: Aug 2020
Location: Clinton,Ms
Posts: 25
|
yeah by some pictures i have looked at thats about right but wanted to see if someone had some cats laying around might could put a tape on them. Thanks though
|
|
|
|
|
12-28-2020, 11:39 PM
|
#4 |
|
Drives: 2020 SS 1LE Join Date: Aug 2020
Location: Dallas Tx
Posts: 65
|
I just did headers, I can measure from the flange for you
|
|
|
|
|
12-29-2020, 10:52 AM
|
#5 | |
|
Drives: 2016 Camaro Join Date: Aug 2020
Location: Clinton,Ms
Posts: 25
|
Quote:
|
|
|
|
|
|
12-30-2020, 07:25 PM
|
#6 |
|
Drives: 2016 Camaro Join Date: Aug 2020
Location: Clinton,Ms
Posts: 25
|
Im still needing this information please.
|
|
|
|
|
12-31-2020, 08:01 AM
|
#7 |
          
Drives: '20 ZLE Join Date: Jun 2020
Location: Mile High
Posts: 4,195
|
Sorry, I can't tell what you're asking. If you're going to cut a bung (8 total) into each exhaust pipe, the bung should be 3" or so from the flange but be careful to locate them such that they do not obstruct other work you will perform such as on spark plugs
__________________
2020 ZL1LE A10.
LME LT4 390 short block, LME CID Heads, Kong E2650, FBO. 15" conversion, MT ET Street R 325/15. 100 octane: 1045hp/1055tq. 100 octane + Meth (1x10+): 1117 hp/1067 tq |
|
|
|
|
12-31-2020, 08:07 AM
|
#8 | |
|
Drives: 17 2SS, 8L90, Cam, Heads, E85 Join Date: Dec 2016
Location: US
Posts: 1,213
|
Quote:
|
|
|
|
|
|
12-31-2020, 06:33 PM
|
#9 |
|
Drives: 2016 Camaro Join Date: Aug 2020
Location: Clinton,Ms
Posts: 25
|
4 bolt flange at converter to 1st o2 sensor
|
|
|
|
|
01-02-2021, 11:16 AM
|
#10 |
|
Drives: 2016 Camaro Join Date: Aug 2020
Location: Clinton,Ms
Posts: 25
|
Anyone?
|
|
|
|
|
|
|
|
|
Post Reply
|
|
|
