08-12-2019, 05:29 PM | #15 |
Drives: 2016 F150 Join Date: May 2019
Location: Michigan
Posts: 169
|
Here's some up close pics. I painted these myself with some 2k satin black. Came out great.
|
08-12-2019, 10:16 PM | #16 |
Drives: 2019 Camaro 2SS 1LE Join Date: Jul 2019
Location: IL
Posts: 28
|
ACS on mine and I love them
__________________
2019 2SS 1LE
|
08-12-2019, 10:18 PM | #17 |
08-13-2019, 09:07 AM | #18 |
Drives: 2019 Camaro 2SS 1LE Join Date: Jul 2019
Location: IL
Posts: 28
|
I love them. They just add so much visually (as you know) but the fit and finish is out standing.
__________________
2019 2SS 1LE
|
06-12-2020, 12:06 PM | #19 |
Hot Camaro
Drives: '20 2SS Convertible 6MT Join Date: May 2020
Location: CT
Posts: 3,541
|
I know this thread is a bit old, but wanted to add a comment here... From what I understand, the EOS products are all described as being "Primer Black" which is nothing more than a color - they are not actually primed. The mold them, clean them up, and that's it.
|
06-13-2020, 11:19 AM | #20 |
|
I wish we could have gotten a better conclusion from this thread.
I am not rolling in the money, so to add splitter, rockers, spoiler, intake, exhaust, and tune is a pretty impossible order to fill..... but i want to. so EOS looks like the best option for me..... but only if it works. If i have to buy things a second time, or pay for labor to fix things before even installing them, then I am certainly not saving money
__________________
|
06-13-2020, 12:15 PM | #21 |
Drives: 2023 SS Vert Join Date: Jan 2020
Location: Ontario
Posts: 241
|
EOS Side Skirts
I put on EOS sideskirts, they were fine. Reasonably priced.
Painted them Satin Black to match my GM front splitter. I recommend galvanized or stainless steel screws rather than the ones they sent, do both underneath and the side angles with screws. I tried 3M tape to hold the sides and it pulled off overnight so cleaned it up and put screws in. I also used black silicone in the slight gap that exists at the last foot of the sides skirts towards the back.
__________________
1978 Z28 T-Roof
1984 Berlinetta 2007 Solstice Supercharged 2014 C7 Z51 2020 RS Convertible 2023 2SS Convertible |
06-13-2020, 08:51 PM | #22 | |
Hot Camaro
Drives: '20 2SS Convertible 6MT Join Date: May 2020
Location: CT
Posts: 3,541
|
Quote:
|
|
06-14-2020, 08:21 AM | #23 |
L8ap3x
|
I had a poor experience with them.
The side skirts were a terrible fitment. So bad I wonder if I just got a set that were molded wrong. The splitter seemed...cheap. put way too much work into painting them and fighting with the fit that I gave up. Got a refund and paid double to order c7. |
06-14-2020, 08:23 AM | #24 | |
L8ap3x
|
Quote:
I wasn't keen on the drilling either but your only drilling into the plastic rocker panel. C7 gave me 40 self tapping screws to do all 3 pieces. Does that tell you anything about how it needs to be secured? |
|
06-14-2020, 10:52 AM | #25 | |
Hot Camaro
Drives: '20 2SS Convertible 6MT Join Date: May 2020
Location: CT
Posts: 3,541
|
Quote:
|
|
06-14-2020, 05:28 PM | #26 | |
Drives: 2023 SS Vert Join Date: Jan 2020
Location: Ontario
Posts: 241
|
Quote:
Mine is a 2020 RS, the EOS kit was specific for this model and the SS. It appeared the molding fit nicely when installed but overnight the side skirt pulled away from the rocker panel. It was 1/2" 3M Molding Tape made for this sort of application. I cleaned the rocker and side skirt with alcohol first, did all the right things. There is enough tension to pull the side skirt away apparently. I just went ahead with screws, fit nicely then, still some gap at the rear though, last foot, others have also reported this. I used painters tape and covered the side skirt and rocker panel and put black silicone in the gap, can't tell unless you get on your knees to look at it. The rocker panel is plastic where you hit it from the side, not a big deal to screw into. As I said I used stainless steel screws , others have used galvanized, not sure about the ones sent to you with the kit whether they won't rust or not so just went ahead with higher quality screws. Here is the tape I used, disappointed in it: https://www.uline.ca/Product/Detail/...E&gclsrc=aw.ds These are the side skirts I ordered from Amazon: https://www.amazon.com/Replacement-2...ef_=ast_sto_dp
__________________
1978 Z28 T-Roof
1984 Berlinetta 2007 Solstice Supercharged 2014 C7 Z51 2020 RS Convertible 2023 2SS Convertible |
|
06-14-2020, 07:53 PM | #27 | |
Hot Camaro
Drives: '20 2SS Convertible 6MT Join Date: May 2020
Location: CT
Posts: 3,541
|
Quote:
I appreciate the input. Mine are supposed to arrive Wednesday but I won't be able to do more than a rudimentary test-fit right away as I have to decide whether to put them on "as is", wrap them, or paint them. |
|
06-16-2020, 04:11 PM | #28 |
Camaro2SS18
Drives: 2018 Chevrolet Camaro 2SS Join Date: Feb 2020
Location: Northern NY
Posts: 81
|
In all honesty, do yourselves a favor and just order the ACS Composites. They really are the best option out there and are the closest to OEM that you will get as far as quality and fitment. I have heard so many issues with Ikon, EOS, C7, ZL1 addons. They either don't fit great and have gaps, the tape doesn't hold, they switch out the hardware because the hardware provided is no good, the paint is not good, some don't have any instructions with them. ACS has everything you need and it is quality. On top of that, they have the best customer service and will take care of you. They also offer to my knowledge, the only rock guards that are compatible with side skirts and still look good and not like a flimsy mud flap. They also have a undertray to compliment the front splitter. They are a bit more pricey, but like someone already stated on here, you get what you pay for and when you pay as much for these cars as we do and you want them to look nice, you just put good quality parts on them to last your investment.
|
|
|
Post Reply
|
|
|