What did you do to your 6th Gen Camaro today?! - Page 567

Thrashed1LE · 03-01-2020, 08:53 PM

Ordered side skirts and knee pads. This thing is going to break me!

1hprush · 03-01-2020, 10:36 PM

Quote:

Originally Posted by Rnovrit

Thank you. Only doing the canards. It always kinda bugged me that they did not match the rear wing though I completely understand why GM used the plastic. These are a set from Trufiber that I modified/had corrected locally. I purchased three sets, each from a separate manufacturer. Trufiber comes with two holes drilled half way through in the back. Anderson Composites is only finished on the top and the bottom is raw resin globs painted flat black. The third company that will remain nameless, made a nice set except upon close examination the carbon fiber is cut short at the edges. You can see the cut line. I ended up using the Trufiber set but had my friends body shop fill in the holes with tinted Fiberglass resin and re-clear them. I also had them add in a flex agent to help with durability. The way the canards are mounted on the car, the underside is exposed on the almost vertical section. This lets you easily see the hole or raw resin from standing near the side of the car. Out of the three I would recommend Trufiber. The Trufiber set also seamed to have a more accurate and robust set of mounting tabs. The two lower tabs are a nice piece of steel rather that just some molded tabs. Everyone at all three companies were very nice. My only issues was with Anderson Composites. I called them to verify the overall finish of the canards and even asked about the finish of the back side before purchasing. Upon arrival I was very disappointed that what they told me was clearly not the case. For the product they provided, they are way over priced in my own personal opinion. I’m not trying to bash them, this was just my personal experience. Please note that my requirements for quality and fit/finish are probably higher than your average customer. The first picture is of the holes in the Trufiber. The second is the no-name company with the carbon fiber cut short. I don’t have a picture of the Anderson Composites canards as I only half unpacked one canard and put it right back in the box.

Thanks for the write-up!

Zapote21 · 03-02-2020, 03:43 PM

And now the front SS logo has been replaced. Later this week, the front splitter gets installed

Martinjlm · 03-02-2020, 04:25 PM

Caved in to my carbon fiber fetish.

BWAYNE2008 · 03-02-2020, 08:11 PM

Finally got around to installing my RPI Stage 1 spoiler.

Need4Camaro · 03-02-2020, 08:35 PM

Quote:

Originally Posted by BWAYNE2008

Finally got around to installing my RPI Stage 1 spoiler.

That car is absolutely gorgeous, nice work. Is that Ceramic coated btw?

cnc237 · 03-02-2020, 09:08 PM

Just ordered a MBRP Adel back from juiced. Come on spring!!!!!

1hprush · 03-02-2020, 09:22 PM

Quote:

Originally Posted by Martinjlm

Caved in to my carbon fiber fetish.

Nice! Where did you order from?

arpad_m · 03-02-2020, 09:57 PM

Quote:

Originally Posted by Martinjlm

Caved in to my carbon fiber fetish.

Isn't it a bit too much, though? Or one can never get enough CF

? Interesting that you didn't replace the shift knob with the CF GM accessory, I think it would complement this new look much better than the original brushed aluminum part.

Martinjlm · 03-02-2020, 10:29 PM

Quote:

Originally Posted by 1hprush

Nice! Where did you order from?

Next Gen Speed.com

Quote:

Originally Posted by arpad_m

Isn't it a bit too much, though? Or one can never get enough CF

? Interesting that you didn't replace the shift knob with the CF GM accessory, I think it would complement this new look much better than the original brushed aluminum part.

Thought about it, but I didn’t really like the look of the one I saw. Kinda looked like a blister. Still waiting on the trim for the nav screen and might add a piece around the start button.

BWAYNE2008 · 03-02-2020, 11:21 PM

Quote:

Originally Posted by Need4Camaro

That car is absolutely gorgeous, nice work. Is that Ceramic coated btw?

Thanks! Yeah, I used hydroslick intense from chemical guys. I am pretty happy with the results.

Drizzt ss · 03-03-2020, 07:58 AM

Quote:

Originally Posted by BWAYNE2008

Finally got around to installing my RPI Stage 1 spoiler.

Beautiful dude, I have the same one, just watch those corners, I had to put some clear bra on the ends because it was making slight contact with the paint.

Rhobz · 03-03-2020, 11:57 AM

I installed the Gen5DIY LED Reverse Light harness last night with LED reverse and license plate lights. I know its a little thing but I am super stoked. It always bothers me when a nice car with crisp bright LED/HID lights all around has bland, yellow halogen reverse and/or license plate lights.

NEGXXIS · 03-03-2020, 01:08 PM

Changed out the bolts on my rear spoiler.
I think they look pretty good.... but the red might be too much.
Im going to run them for a while and see if I get tired of the look.
Luckily they sell them in black also.

Before and after pics ...

03-01-2020, 08:53 PM	#7925
Thrashed1LE Drives: Chevrolet Camaro Join Date: Feb 2020 Location: 23838 Posts: 34	Ordered side skirts and knee pads. This thing is going to break me! __________________ Roto Fab CAI GM Performance Parts red knee pads and 1LE floor mats Mishimoto catch can GM Spectrum Lighting Alpine component speakers, JBL amp, Magnum Subs 3M tinted windows ZL1 Add Ons front and rear rock guards Stainless Works headers and x-pipe Borla ATAK axleback exhaust Dyno tuned at National Speed, 464rwhp, 493ft lbs Next up, MSD intake manifold and another set of dyno tunes

03-02-2020, 03:43 PM	#7927
Zapote21 Tampa Bay Camaros Drives: 2017 Krypton Green 2SS Join Date: Jul 2011 Location: Westfield, IN Posts: 1,042 View My Garage	And now the front SS logo has been replaced. Later this week, the front splitter gets installed Attached Images __________________ Me and wife, in order 2011 2SS SGM 2013 2SS Hot wheels vert 2016 C7 DSOM 2012 2SS yellow vert 2017 2LT Krypton Green 2018 2LT Hot wheels crush 2020 2SS Shock vert. 2017 2SS Krypton Green coupe

03-02-2020, 04:25 PM	#7928
Martinjlm Retired fr GM + SP Global Drives: 2017 Camaro Fifty SS Convertible Join Date: Mar 2017 Location: Detroit Posts: 6,043	Caved in to my carbon fiber fetish. Attached Images __________________ 2017 CAMARO FIFTY SS CONVERTIBLE A8 \| MRC \| NPP \| Nav \| HUD \| GM Performance CAI \| Tony Mamo LT1 V2 Ported TB \| Kooks 1-7/8” LT Headers \| FlexFuel Tune \| Thinkware Q800 Pro front and rear dash cam \| Charcoal Tint for Taillights and 3rd Brakelight \| Orange and Carbon Fiber Bowties \| 1LE Wheels in Gunmetal Gray \| Carbon Fiber Interior Overlays \| Novistretch bra and mirror covers \| Tow hitch for bicycle rack \|

03-02-2020, 08:11 PM	#7929
BWAYNE2008 Drives: 2018 Camaro 2SS Join Date: Dec 2014 Location: Albuquerque Posts: 64	Finally got around to installing my RPI Stage 1 spoiler. Attached Images

03-02-2020, 09:08 PM	#7931
cnc237 Drives: 2019 Camaro 2SS 1LE Join Date: Jul 2019 Location: IL Posts: 28	Just ordered a MBRP Adel back from juiced. Come on spring!!!!! __________________ 2019 2SS 1LE

03-03-2020, 11:57 AM	#7937
Rhobz Drives: 2018 Camaro 1SS 1LE Join Date: Feb 2020 Location: Colorado Springs, CO Posts: 186	I installed the Gen5DIY LED Reverse Light harness last night with LED reverse and license plate lights. I know its a little thing but I am super stoked. It always bothers me when a nice car with crisp bright LED/HID lights all around has bland, yellow halogen reverse and/or license plate lights.

03-03-2020, 01:08 PM	#7938
NEGXXIS Drives: 2019 Camaro SS A10 Join Date: May 2009 Location: Tempe, Arizona Posts: 1,062 View My Garage	Changed out the bolts on my rear spoiler. I think they look pretty good.... but the red might be too much. Im going to run them for a while and see if I get tired of the look. Luckily they sell them in black also. Before and after pics ... __________________ 2020 Range Rover Sport HSE P525 Supercharged 5.0 - Firenze Red - 9012 wheels SOLD 2019 Camaro SS -Wrapped in Matte Magnectic Black - Anderson Carbon Hood and Rear Spoiler – Ikon front spoiler – OEM ZL1 Side Rockers - ZL1 Addons Diffuser - BMR 1.0” Lowering Springs - MRR 228 Wheels 20x10 and 20x11 RIP 2016 Camaro SS https://www.camaro6.com/forums/showthread.php?t=565453 SOLD 2010 Camaro SS Featured in GM High Tech Performance and Camaro Now Magazines - http://www.superchevy.com/features/g...of-perfection/

User Name		Remember Me?
Password