2650 MAT - What is your experience? - Page 7

EDFHOBBIES · 01-12-2023, 04:52 PM

Email fine I remember u asked about temps

JSH · 01-12-2023, 05:11 PM

Quote:

Originally Posted by EDFHOBBIES

Email fine I remember u asked about temps

On the last pull, MAT was 78F at almost 7,100 rpm; IAT 64F. No ice. Coolant 172.

2941# FRP, 81 FP.

Still working on the 104 tune, then get baseline dyno.

KingLT1 · 01-12-2023, 07:57 PM

The MAT isn't reading right. It doesn't matter either way...it's not pulling timing.

JSH · 01-12-2023, 08:43 PM

Quote:

Originally Posted by KingLT1

The MAT isn't reading right. It doesn't matter either way...it's not pulling timing.

The number doesn't look too far off. I'll look at the channel list tomorrow to see if it's being polled. There might be an ACT channel too.

KingLT1 · 01-13-2023, 08:40 AM

Quote:

Originally Posted by JSH

The number doesn't look too far off. I'll look at the channel list tomorrow to see if it's being polled. There might be an ACT channel too.

MAT is never going to be 14 degrees over ambient on a setup like yours. "Maybe" if you were only making 7psi of boost. Either way it was reading in the 130-140 range and no changes have been made. I would try deleting the PID and then add it back.

JSH · 08-25-2023, 08:22 AM

Quote:

Originally Posted by Joshinator99

I bought a CWA-150 and it’s sitting in my garage. That’s definitely going in this winter. The Varimax isn’t cutting it IMO.

The car was in the shop this week for:

Pierburg CWA400 (heat wrapped),
DSX belt idler assembly,
2.625 upper pulley
DEI Fire Wrap on engine compartment hoses,
Shift light,
Repaired RR level sensor link, which wasn't planned.

I decided to postpone a redo of the tank's plumbing until I see how much good this project accomplished.

*radz28* · 08-25-2023, 10:12 AM

NICE!!! Fingers crossed for the improvements you're working toward.

adamjwilson · 08-25-2023, 12:35 PM

You are going to like that Pierburg pump... much superior to that Bosch junk that comes with the Whipple

JSH · 08-25-2023, 07:20 PM

You can see the hole where the stock idler was mounted and DSX bracket provides a lot more belt wrap. I'm also going to wrap the engine water hose.

JSH · 08-26-2023, 05:27 PM

There's no way for me to test the Craig Davies versus the Pierburg water pumps, but just by sticking my hand in the tank and feeling the thrust of the water and looking at the turbulence on top of the water, I would say that the Pierburg puts out 50 to 75% more

*Joshinator99* · 08-26-2023, 07:17 PM

Quote:

Originally Posted by JSH

There's no way for me to test the Craig Davies versus the Pierburg water pumps, but just by sticking my hand in the tank and feeling the thrust of the water and looking at the turbulence on top of the water, I would say that the Pierburg puts out 50 to 75% more

Exactly which Davies Craig pump were you using?

JSH · 08-26-2023, 07:59 PM

Quote:

Originally Posted by Joshinator99

Exactly which Davies Craig pump were you using?

8160, which is an inexpensive pump

*Joshinator99* · 08-26-2023, 09:10 PM

Quote:

Originally Posted by JSH

8160, which is an inexpensive pump

Looks like the new Pierburg has nearly triple the differential pressure of the Davies Craig pump so it should be able to really force the water through the tubing, even if it’s a bit undersized. Looks to be a pretty significant difference. Pump curves attached.

JSH · 08-27-2023, 08:27 AM

Quote:

Originally Posted by Joshinator99

Looks like the new Pierburg has nearly triple the differential pressure of the Davies Craig pump so it should be able to really force the water through the tubing, even if it’s a bit undersized. Looks to be a pretty significant difference. Pump curves attached.

Yeah, I didn't know the figures were that large, but the difference was immediately obvious when I turned on the pump. Thanks for posting the diagram.

01-12-2023, 04:52 PM	#85
EDFHOBBIES Dyno Show Queen LOL Drives: 16 SS & 17 ZL1 Both Yellow Join Date: Jan 2014 Location: Houston Posts: 4,354 View My Garage	Email fine I remember u asked about temps __________________ Kong Ported 2650, Crawford Racing Port Injection, Weapon X 112mm Adapter, NW112mm TB, Livernois Ported LT4 Heads, Lingenfelter GT32 stealth cam, Haltech Elite, and Carbon by Trufiber

01-12-2023, 07:57 PM	#87
KingLT1 Drives: 2016 1SS NFG A8 Join Date: Aug 2017 Location: 46804 Posts: 7,661	The MAT isn't reading right. It doesn't matter either way...it's not pulling timing. __________________ 2016 NFG SS A8/Whipple 2.9/Fuel System/Flex Fuel

08-25-2023, 10:12 AM	#91
radz28 Petro-sexual Drives: Ultra-Grin Join Date: Oct 2006 Location: Crazy Coast Posts: 15,855 View My Garage	NICE!!! Fingers crossed for the improvements you're working toward. __________________ '20 ZL1 Black "Fury" A10, PDR, Exposed CF Extractor Magnuson Magnum DI TVS2650R // RFBG // Soler 103 // TooHighPSI Port Injection // THPSI Billet Lid // FF // Katech Drop-In // PLM Heat Exchanger // ZLE Cradle bushings // BMR Chassis-Suspension Stuff // aFe Bars // Diode Dynamics LEDs // ACS Composites Guards // CF Dash // Aeroforce // tint // other stuffs

08-25-2023, 12:35 PM	#92
adamjwilson Drives: 2022 Camaro 2SS A10 Join Date: Jul 2022 Location: FL Posts: 529	You are going to like that Pierburg pump... much superior to that Bosch junk that comes with the Whipple __________________ 2022 Camaro 2SS/ Whipple 3.0 / 2"Headers/ PRC LTX Heads/ Forged Internals/LT4 fueling/ DSX Aux/ DSX Flex Fuel/ Meth Injection/ Katech 112 TB/ RotoFab Big Gulp/ Corsa NPP/ Various exterior mods

08-25-2023, 07:20 PM	#93
JSH Drives: '20 ZLE Join Date: Jun 2020 Location: Mile High Posts: 4,195	You can see the hole where the stock idler was mounted and DSX bracket provides a lot more belt wrap. I'm also going to wrap the engine water hose. Attached Images __________________ 2020 ZL1LE A10. LME LT4 390 short block, LME CID Heads, Kong E2650, FBO. 15" conversion, MT ET Street R 325/15. 100 octane: 1045hp/1055tq. 100 octane + Meth (1x10+): 1117 hp/1067 tq Last edited by JSH; 08-27-2023 at 08:33 AM.

08-26-2023, 05:27 PM	#94
JSH Drives: '20 ZLE Join Date: Jun 2020 Location: Mile High Posts: 4,195	There's no way for me to test the Craig Davies versus the Pierburg water pumps, but just by sticking my hand in the tank and feeling the thrust of the water and looking at the turbulence on top of the water, I would say that the Pierburg puts out 50 to 75% more __________________ 2020 ZL1LE A10. LME LT4 390 short block, LME CID Heads, Kong E2650, FBO. 15" conversion, MT ET Street R 325/15. 100 octane: 1045hp/1055tq. 100 octane + Meth (1x10+): 1117 hp/1067 tq

User Name		Remember Me?
Password