[Brianw36]

Originally Posted by Puddin

Its 2.75in.

Thanks

[ss2fast4u]

I have a 3 inch flowmaster xpipe would the 60606 bolt up to that?

[coruiz]

Originally Posted by ss2fast4u

I have a 3 inch flowmaster xpipe would the 60606 bolt up to that?

the borla 60606 and Flowmaster x pipe are both mid pipes...

you mean you have the flowmaster axle back?

[ss2fast4u]

oh my mistake i was referring to the borla secondary cat delete only section. I mixed up this number with the 60626.

[coruiz]

Originally Posted by ss2fast4u

oh my mistake i was referring to the borla secondary cat delete only section. I mixed up this number with the 60626.

No worries, I have studied this setup as I am split between the Stainless Works full cat back or the 60626 (or the 60663, which is 2.75") connecting to the FLowmaster X pipe and their NPP axle back.

I have found that it can work but you will have to cut some of the Borla pipe in order to work

[ss2fast4u]

Originally Posted by coruiz

No worries, I have studied this setup as I am split between the Stainless Works full cat back or the 60626 (or the 60663, which is 2.75") connecting to the FLowmaster X pipe and their NPP axle back.

I have found that it can work but you will have to cut some of the Borla pipe in order to work

thats the setup I have. I have their xpipe and npp exhaust. I recently had the secondary cats removed but the pipes they installed are leaking now and I rather just install the 60626 and not deal with it. When it wasnt leaking at first it sound awesome I am glad I did it.

[coruiz]

Originally Posted by ss2fast4u

thats the setup I have. I have their xpipe and npp exhaust. I recently had the secondary cats removed but the pipes they installed are leaking now and I rather just install the 60626 and not deal with it. When it wasnt leaking at first it sound awesome I am glad I did it.

Mine were leaking too when I removed the secondary cats and I put a generous amount of Permatex Muffler & Tailpipe Sealer all around the welds. It's a temp fix until I figure out which way to go.

https://www.permatex.com/products/sp...ilpipe-sealer/

[coruiz]

Originally Posted by ss2fast4u

thats the setup I have. I have their xpipe and npp exhaust. I recently had the secondary cats removed but the pipes they installed are leaking now and I rather just install the 60626 and not deal with it. When it wasnt leaking at first it sound awesome I am glad I did it.

Do you have a video showing your setup, I'm really interested

[ss2fast4u]

unfort I dont and now it sounds different due to the leak. I will be ordering the 60626 later in the week and will install that once it arrives.

[Chris C 1SS 1LE]

You're hijacking my thread. All good...how about those clamps for mating the 60606 and suitcase? Think this likely temp setup. Suspect I'll put a magnaflow comp series axle back on.

[Jhunsberger]

Maybe some info in this thread would be helpful.

https://www.camaro6.com/forums/showthread.php?t=536188

[coruiz]

Originally Posted by Chris C 1SS 1LE

You're hijacking my thread. All good...how about those clamps for mating the 60606 and suitcase? Think this likely temp setup. Suspect I'll put a magnaflow comp series axle back on.

Vibrant clamps will do the trick

Didn't mean to hijack the thread brother, my bad

[Chris C 1SS 1LE]

All good. Been doing this a long time. Tango for clamp 411

[Chris C 1SS 1LE]

Probably be 3 weeks before I get around to install. Conflicts. Going to clamp then see from there. Magnaflow is 3" so the pipes will slide in and clamp up if I chose that route. Need to find the clamps. Search turns up too many returns.