03-09-2018, 08:45 PM | #1 |
Drives: 2015 Camaro 1SS Join Date: Dec 2017
Location: Antelope, CA
Posts: 208
|
PCV hose?
Anyone know of an easy way to remove the PCV hose from the back of the intake?
|
03-10-2018, 09:53 AM | #2 |
Big Samoan ina little car
Drives: 2016 camaro Join Date: May 2014
Location: Tofiga Island
Posts: 1,872
|
should just unclip...
Front side is the larger rubber piece. Back side is the smaller plastic piece. It really doesnt get any easier than this....
__________________
Don't sit around and watch everyone else live YOUR dreams...DO SUMPT'N
When I see posts asking "whats the best intake, exhaust, etc" .... the answer to that is like a grandfather telling his grandkids "if you put salt on a birds tail, it'll let you catch it" #ThinkAboutIt "Winning Tip: Don't take my (or anyone else's) word for it. GO TEST IT!" - Dennis Grant |
03-10-2018, 10:32 AM | #3 |
603 Camaros
Drives: 2017 NGM I4 1LT Coupe Join Date: May 2012
Location: Manchester, NH
Posts: 6,779
|
2017+ has an annoying disconnect on it. Not the same as 2016 a lot of people break them.
__________________
MY 2017 I4 CAMARO BUILD JOURNAL | YOUTUBE | INSTAGRAM | 316RWHP - 385 RWTQ HPTUNERS DYNO TUNE | 12.693s @ 105MPH 1/4 Mile |
03-10-2018, 10:36 AM | #4 |
Drives: Sold! Join Date: Nov 2017
Location: SoCal
Posts: 105
|
Wouldn’t be nearly as bad if you could actually see it.
When I did my catch can I unhooked the front side but I just cut it with it mounted on the car rather than mess with the rear connection. |
03-10-2018, 02:05 PM | #5 |
Drives: 2015 Camaro 1SS Join Date: Dec 2017
Location: Antelope, CA
Posts: 208
|
My problem is I can't even feel the fitting, it goes under a piece of metal.
|
03-10-2018, 03:03 PM | #6 |
603 Camaros
Drives: 2017 NGM I4 1LT Coupe Join Date: May 2012
Location: Manchester, NH
Posts: 6,779
|
Try contacting Jason@ or have a shop remove it it's a Pain in the ass to do without a tool GM dealerships and most repair shops have the tool. Maybe check a local auto parts store see if they have a rental tool.
__________________
MY 2017 I4 CAMARO BUILD JOURNAL | YOUTUBE | INSTAGRAM | 316RWHP - 385 RWTQ HPTUNERS DYNO TUNE | 12.693s @ 105MPH 1/4 Mile |
03-15-2018, 09:01 PM | #7 |
Drives: 2015 Camaro 1SS Join Date: Dec 2017
Location: Antelope, CA
Posts: 208
|
I ordered new PCV hoses because I couldn't find the quick connect fittings anywhere. I received the hoses today, and have a better idea of where the fitting is. Sadly i wasn't able to get to the catch can installed, will need more hose and possibly other fittings/adapters for a clean install. I was able to do the clean side separator.
New PCV hoses Cut off the fittings, will keep the center fitting for when I install the GM intake. For what ever reason the braided hose upgrade isn't available on the CSS. So i picked up some -8 and -6 hose from my local speed shop. |
03-15-2018, 09:26 PM | #8 | |
Big Samoan ina little car
Drives: 2016 camaro Join Date: May 2014
Location: Tofiga Island
Posts: 1,872
|
Quote:
Good install
__________________
Don't sit around and watch everyone else live YOUR dreams...DO SUMPT'N
When I see posts asking "whats the best intake, exhaust, etc" .... the answer to that is like a grandfather telling his grandkids "if you put salt on a birds tail, it'll let you catch it" #ThinkAboutIt "Winning Tip: Don't take my (or anyone else's) word for it. GO TEST IT!" - Dennis Grant |
|
|
|
Post Reply
|
|
|