[77Z28]

I took the car cover off after a few months in storage and went for a little drive. It is almost like driving it for the first time again.

[jwober]

Came out of winter storage, went for the first ride of the season

[camaromike77]

Originally Posted by MANNAXMAN

I like the decal on the strut tower brace. Where did you get it?

Thanks MANNAXMAN. I was bored one day and searched eBay. Didn't really know what to expect, but was very impressed when it arrived.

[camaromike77]

Originally Posted by Red Devil's Rebel

Looks great, nice upgrade!

What screws are those under there btw?
Did you need a hex key or would it be a torx screwdriver? Size?
Thanks! I may be switching mine out as well

Thanks Red Devil's Rebel. It is a T25 Torx screwdriver. There are 5 of the screws in there, and a "snap" near the front. Very easy to replace, and looks AWESOME! Should have come standard with the Fifty!

[camaromike77]

Originally Posted by 77Z28

I took the car cover off after a few months in storage and went for a little drive. It is almost like driving it for the first time again.

Originally Posted by jwober

Came out of winter storage, went for the first ride of the season

Attachment 860196

Mine came "out of storage" yesterday, but no insurance until April 3. However, I got to sit in it while it was in my garage!!! What a TEASE!!!!!

[jwober]

Originally Posted by camaromike77

Mine came "out of storage" yesterday, but no insurance until April 3. However, I got to sit in it while it was in my garage!!! What a TEASE!!!!!

Had to get my fix while I could, cold and rainy for the next 10 days .

Where did you get your console lid? Agreed, It should have been standard!

[Night Vision Universe]

Installed the GM Black tail lights and added a Black SS emblem to each side of the side skirts...

[John20162SS]

Originally Posted by Night Vision Universe

Installed the GM Black tail lights and added a Black SS emblem to each side of the side skirts...

Looks great, emblems are a nice touch

[camaromike77]

Originally Posted by jwober

Had to get my fix while I could, cold and rainy for the next 10 days .

Where did you get your console lid? Agreed, It should have been standard!

I hear ya!!!

I bought my console lid from CrateEngineDepot.com in Grayslake, Illinois. List was $225.00, but I paid $191.00. I would touch base with Maureen or Becky at Rogers Chevrolet (Sponsor Forum), as they can probably match or even beat the price.........

[John20162SS]

Matt at ThatGMpartguy.com has it for $177

http://www.thatgmpartsguy.com/oe-gm/84092717

[webberj1]

Installed Eibarch pro kit lowering springs yesterday.

[jwober]

Originally Posted by camaromike77

I hear ya!!!

I bought my console lid from CrateEngineDepot.com in Grayslake, Illinois. List was $225.00, but I paid $191.00. I would touch base with Maureen or Becky at Rogers Chevrolet (Sponsor Forum), as they can probably match or even beat the price.........

Thanks Mike, was USD or Canadian I will email Maureen
Jim

Originally Posted by John20162SS

Matt at ThatGMpartguy.com has it for $177

http://www.thatgmpartsguy.com/oe-gm/84092717

Thanks,
Jim

[chozn4service]

ZL1 Addons jack pads. A must have and a pain in the tail to install being 6wks Post Op bilateral knee replacement surgery and really shouldn't be on the ground. Not a lot of room to work with when screwing the set screws inward position. Two down and two to go. Time for a hydrocodone!!!!!!





Sent from my iPhone using Tapatalk

[Red Devil's Rebel]

Originally Posted by camaromike77

Thanks Red Devil's Rebel. It is a T25 Torx screwdriver. There are 5 of the screws in there, and a "snap" near the front. Very easy to replace, and looks AWESOME! Should have come standard with the Fifty!

Thanks so much, I appreciate the info!