04-22-2019, 01:31 PM | #1 |
Dyno Show Queen LOL
Drives: 16 SS & 17 ZL1 Both Yellow Join Date: Jan 2014
Location: Houston
Posts: 4,345
|
Will 345 fit on the ZL1 or SS?
Running a 325 30 19 right now with the MRR Zl1 1LE reps...
Will a 345 30 20 fit? Any Pros or Cons? width goes from 12.8 to 13.6 height is only 27.1.. I had some 305 35 20s on before that were 28 plus tall.. Would it make any difference on a 43mm offset?
__________________
Kong Ported 2650, Crawford Racing Port Injection, Weapon X 112mm Adapter, NW112mm TB, Livernois Ported LT4 Heads, Lingenfelter GT32 stealth cam, Haltech Elite, and Carbon by Trufiber |
04-22-2019, 01:33 PM | #2 |
Drives: ZL1 1LE Join Date: Oct 2018
Location: NYC (almost)
Posts: 339
|
A member is running 345/18s and I’d like to run a 345/18 drag radial...curious to see what the size differences between the race slicks being used vs a street tire or drag radial
https://www.camaro6.com/forums/showthread.php?t=549850 |
04-23-2019, 10:33 AM | #3 |
Drives: 2016Camaro+1968Chevelle+1954BelAir Join Date: Feb 2013
Location: NH
Posts: 149
|
I can say a 335 30 20 (27.9x13.2)fits perfect on a 38 offset with wire relocation and some molding of the wheel well liner with a heat gun. Based on the clearances i have with that setup id say its absolutly possible to fit 345 30 19. You may have to run a 5-8mm spacer and expended lugs
__________________
"Lead me, follow me, or get out of my way." GGSP
|
04-25-2019, 12:02 PM | #4 |
Red Hot SS
Drives: 2017 Camaro 2SS Join Date: Nov 2013
Location: Winnipeg, Manitoba, Canada
Posts: 150
|
A 345 x 30/20 will be 28.28" tall. Just so you know.
|
04-25-2019, 01:47 PM | #5 |
Dyno Show Queen LOL
Drives: 16 SS & 17 ZL1 Both Yellow Join Date: Jan 2014
Location: Houston
Posts: 4,345
|
I run 19s..
And discount just called me they are here.. now I got a decision put them on going out of town or wait till Monday when new rims show!
__________________
Kong Ported 2650, Crawford Racing Port Injection, Weapon X 112mm Adapter, NW112mm TB, Livernois Ported LT4 Heads, Lingenfelter GT32 stealth cam, Haltech Elite, and Carbon by Trufiber |
04-26-2019, 06:39 AM | #6 |
Drives: 18 ZL1 nightfall grey A10 Join Date: Apr 2018
Location: RGV Texas
Posts: 1,527
|
I’m looking into going 315/30/20 with a 20x11.5 wheel. Just trying to nail the offset. Going that wide with the hopes that I can fit a 325/30/20 later on.
|
04-26-2019, 07:24 AM | #7 |
SABIO
Drives: 2016 CAMARO 1SS Join Date: Jul 2015
Location: Bradford, ON
Posts: 5,012
|
325 on a 11.5 is not an issue.
Just pick the right offset. +41 seems right. 2mm more poke out than a 1le wheel. 3 mm closer to the strut
__________________
|
04-26-2019, 08:48 AM | #8 | |
Drives: 2016Camaro+1968Chevelle+1954BelAir Join Date: Feb 2013
Location: NH
Posts: 149
|
Quote:
Then all you would need is a 3-5mm spacer to run 335 or 345 Make sure you mold the inner liner very well
__________________
"Lead me, follow me, or get out of my way." GGSP
|
|
04-26-2019, 08:56 AM | #9 |
Drives: 2016Camaro+1968Chevelle+1954BelAir Join Date: Feb 2013
Location: NH
Posts: 149
|
FYI i have a good thumbs width of clearance behind my 335 30 20 and about a pinky in the quarter gap at full at full squat lol...yup thats what she said.
38 offset
__________________
"Lead me, follow me, or get out of my way." GGSP
|
04-26-2019, 09:38 AM | #10 |
Drives: 18 ZL1 nightfall grey A10 Join Date: Apr 2018
Location: RGV Texas
Posts: 1,527
|
|
04-26-2019, 10:26 AM | #11 |
Drives: 2016Camaro+1968Chevelle+1954BelAir Join Date: Feb 2013
Location: NH
Posts: 149
|
Ps2 335 30 20
Ive also ran a few sets of 325 30 20 r888 and dunlop sport maxx. They all seem about the same size but the ps2 just looks wider in the rear due to the flat tread pattern. FYI The dunlops are a great value for putting down power in the corners but not good at all at launch. Also i could never find a good psi and the center tread always wore fast. Id go back to the r888 but i just dont like paying for them. I DD and car eats them up quick. Boosted M6
__________________
"Lead me, follow me, or get out of my way." GGSP
|
04-26-2019, 08:05 PM | #12 |
Drives: 18 ZL1 nightfall grey A10 Join Date: Apr 2018
Location: RGV Texas
Posts: 1,527
|
I just placed an order for 20x10 with 20mm OS and 20x11.5 with 41mm OS. Going to run 315/30/20 or if possible 325/30/20.
|
04-27-2019, 12:35 AM | #13 |
Drives: 2019 ZL1 Join Date: Mar 2019
Location: florida
Posts: 41
|
Just to be clear, will a 315 30 20 on the factory 2019 ZL1 rear with 43 mm offset clear with the wiring harness moved? I'm new to ZL1 so please excuse my lack of knowledge. Car is on order so can't measure at this time. Thanks for any input.
|
|
|
Post Reply
|
Thread Tools | |
|
|