You are browsing camaro5 
 |
|
10-27-2016, 09:27 AM
|
#15 |
 
Drives: 2007 Corvette C6 983 RWHP Join Date: Dec 2011
Location: Montreal, Canada
Posts: 690
|
__________________
2007 C6 vert, auto, F55, LT3
LME LS402 , WCCH 245 Heads, Pat G. Custom cam YSI / 3.0 pulley, ARH 1 7/8 headers, NPP Dewitts / dual spals, A&A dual pump fuel system. 3.42 polished gears, hardened shafts, Alky control meth, Cartech line lock, ECS axle loops, Trans brace, 6L80 built by me. ID 1000 injectors, comp rockers, Morel lifters, BT springs, Trend 3/8 pushrods, ATI 10% OD Damper Circle D Triple Disc stall 1009 RWHP @ 7000, 817 RWTQ @ 6000, |
|
|
|
10-27-2016, 10:03 AM
|
#16 |
|
Drives: 2010 Camaro 2SS M6 - Intake/Exhaust Join Date: Sep 2014
Location: Bridgewater
Posts: 693
|
Thanks guys. This makes me feel better. My MAF would be maxxed out if I reached the 15000Hz column correct (which i am not at).
|
|
|
|
|
10-27-2016, 10:12 AM
|
#17 |
|
Served USN - Atomic Chimp
Drives: 13 Camaro LSX434 TT M6, 21 ZLE A10 Join Date: Jul 2012
Location: Fort Collins, CO
Posts: 1,605
|
From my new understanding, you've max'd out the PID, not the MAF.
I would like to know where Dynamic Airflow comes from? Calculated?
__________________
 In excess of 1,000WHP LSX434 | AGP 65/65 TT | BTR Equalizer Intake | Trickflow 245cc cathedral | BTR custom cam | Cortex EBC | n2mb WOT | ID-1700x | Brisk GR12S | RPM Lv 7 TR6060 | AGP's Triple 525LPH Fore Fuel | Monster LT1-S Triple | 4.11 DSS Proform 9", CF driveshaft, 1400hp axles | Hurst Line Lock | MGW Retro Short Throw w/old skool Hurst T-handle | ADM solid subframe mounts | Prothane Motor Mounts | Revshift Poly Trans insert | Moreno camber/caster plates |
|
|
|
|
10-27-2016, 10:29 AM
|
#18 | |
|
Too much is never enough!
Drives: AGP TT SS [COTW] 4/20/15 Join Date: Feb 2014
Location: Toledo,OH
Posts: 4,149
|
Quote:
__________________
AGP TT kit, 54/57 Forged rotating assembly, Custom grind cam... Dual nozzle meth, ID850's, Livernois dual fuel pumps, ECS BAP, 25% UDP, 3 inch Magnaflow catback with X pipe, Mantic 9000 clutch, DSS 1000hp axles, DSS aluminum driveshaft, ZL1 rear end, solid subframe bushings, HE differential offset bushings, BMR Trailing arm, BMR toe rods, Lingenfelter LNC-2000,SJM Line Lock. 747 whp 714wtq
Build thread http://www.camaro5.com/forums/showth...55#post8107855 |
|
|
|
|
|
10-27-2016, 10:32 AM
|
#19 |
|
Drives: 2007 Corvette C6 983 RWHP Join Date: Dec 2011
Location: Montreal, Canada
Posts: 690
|
It takes a lot to run out of maf. You can extend the range some with a bigger inlet tube also. IF interested in dyn air flow and such things, searching hp tuners forums will be best reading.
__________________
2007 C6 vert, auto, F55, LT3
LME LS402 , WCCH 245 Heads, Pat G. Custom cam YSI / 3.0 pulley, ARH 1 7/8 headers, NPP Dewitts / dual spals, A&A dual pump fuel system. 3.42 polished gears, hardened shafts, Alky control meth, Cartech line lock, ECS axle loops, Trans brace, 6L80 built by me. ID 1000 injectors, comp rockers, Morel lifters, BT springs, Trend 3/8 pushrods, ATI 10% OD Damper Circle D Triple Disc stall 1009 RWHP @ 7000, 817 RWTQ @ 6000, |
|
|
|
|
10-27-2016, 10:54 AM
|
#20 |
|
Drives: 2010 Camaro 2SS M6 - Intake/Exhaust Join Date: Sep 2014
Location: Bridgewater
Posts: 693
|
If I do max it out, I'll roll to speed density. I think I got a good ways to go.
|
|
|
|
|
10-27-2016, 02:38 PM
|
#21 | |
|
Too much is never enough!
Drives: AGP TT SS [COTW] 4/20/15 Join Date: Feb 2014
Location: Toledo,OH
Posts: 4,149
|
Quote:
__________________
AGP TT kit, 54/57 Forged rotating assembly, Custom grind cam... Dual nozzle meth, ID850's, Livernois dual fuel pumps, ECS BAP, 25% UDP, 3 inch Magnaflow catback with X pipe, Mantic 9000 clutch, DSS 1000hp axles, DSS aluminum driveshaft, ZL1 rear end, solid subframe bushings, HE differential offset bushings, BMR Trailing arm, BMR toe rods, Lingenfelter LNC-2000,SJM Line Lock. 747 whp 714wtq
Build thread http://www.camaro5.com/forums/showth...55#post8107855 |
|
|
|
|
|
|
|
|
 |
|
|
