07-02-2022, 07:27 AM | #1 |
Drives: 2014 2SS/RS 6SP Ashen Grey Join Date: Aug 2021
Location: NY
Posts: 1,264
|
Car creaking noise when Car twists after suspension mods.
Hi, I notice if you out the car in a position where the car twists a little like entering a driveway or something the car will creak a little and it sounds like it is coming from maybe the rear right, Just wondering if that is failrly normal for the up grades i have done.
Adjustable sways, BMR Trailing/Toe and LCA. Z/28 UCA, Hotckis Brace and 1" Spings, Solid Cradle Bushings.
__________________
GM 3.91/TrueTrac OEM ZL1 Rims, Brakes & Side Skirts.ACST4 Splitter/Deflectors NPP M2W,GM Short Throw,Remote Clutch reservoir
GPI Ported Rod Mod,BO White PTB,CAI/JRE Scoop, Moroso Catch Can GC Aluminum DS Stainless Works Ceramic LTH/HiFlo Cats SCT X4 Dynosteve, Hotckis 1" Springs & Chassis Max Brace BMR Adjustable Swaybars,Trailing Arms, Adjustable Toe Rod, LCA & Z28 UCA Bushings Hendrix Solid Cradle Bushings Pedders Radius Rod Inserts Strut tower brace Hero Smoked Tail and 3rd Brake Light, Diode Dynamic SL1 Fog Lights AeroForce Dual gauge/Autometer pillar mount. |
07-02-2022, 09:22 AM | #2 |
Drives: 2010 SS 2SS M6 Join Date: Aug 2016
Location: Smithsburg, Md.
Posts: 2,445
|
did you tq the bolts at ride height?
__________________
2010 SS 2SS M6 - Tune by RDP dynoSteve!(Woot) - Daily Driver - 150K! - All work by me...
|
07-02-2022, 12:11 PM | #3 |
Drives: 2014 2SS/RS 6SP Ashen Grey Join Date: Aug 2021
Location: NY
Posts: 1,264
|
Yes, I installed everything and then drove it onto a drive on lift and torque everything to spec, Only thing I did not torque but did tighten on the Drive on were the Z/28 UCA bushings as I had a hard time getting anything in there to do it so I just tighten those down. All my bushings in the back are BMR with Metal inserts then spin so really dont think it matters if it is at ride height but I did it any way.
Cradle to Body bushings were not done at ride height but they don't matter.
__________________
GM 3.91/TrueTrac OEM ZL1 Rims, Brakes & Side Skirts.ACST4 Splitter/Deflectors NPP M2W,GM Short Throw,Remote Clutch reservoir
GPI Ported Rod Mod,BO White PTB,CAI/JRE Scoop, Moroso Catch Can GC Aluminum DS Stainless Works Ceramic LTH/HiFlo Cats SCT X4 Dynosteve, Hotckis 1" Springs & Chassis Max Brace BMR Adjustable Swaybars,Trailing Arms, Adjustable Toe Rod, LCA & Z28 UCA Bushings Hendrix Solid Cradle Bushings Pedders Radius Rod Inserts Strut tower brace Hero Smoked Tail and 3rd Brake Light, Diode Dynamic SL1 Fog Lights AeroForce Dual gauge/Autometer pillar mount. |
07-02-2022, 02:44 PM | #4 |
Drives: 15 Camaro 2SS M6 Join Date: Jan 2020
Location: BC
Posts: 732
|
check your sway bar and make sure it was installed properly, sounds like a sway issue.
when you greased after your install did you see grease coming out of the bushings? I have seen bad grease nipples in the past. |
07-02-2022, 07:01 PM | #5 |
not afraid of the wall
Drives: Camaros Join Date: Apr 2010
Location: Pittsburgh
Posts: 2,148
|
I have rod ends and they squeak. I lube them with dry lube which works fine until they get wet.
__________________
2023 1LE 1SS BCD GCF JF5 MN6 SIA SLN UQT
10/13/22: 1100 Past Camaros: 13 1LE|02 SS|01 Z28|00 SS|91 1LE|91 Z28|89 IROC-Z |
07-02-2022, 09:01 PM | #6 |
Drives: 2014 2SS/RS 6SP Ashen Grey Join Date: Aug 2021
Location: NY
Posts: 1,264
|
I can check the Bar again yes, I had Grease coming out both sides, I used Amsoil #2 first then I switched to Super Lube.Maybe I'll spray silicon spray on the Sway Bar end links, When i installed the bar I was not 100% Sure which way it went in, The one way it looks like it would have hit the springs, the other way it is close.
__________________
GM 3.91/TrueTrac OEM ZL1 Rims, Brakes & Side Skirts.ACST4 Splitter/Deflectors NPP M2W,GM Short Throw,Remote Clutch reservoir
GPI Ported Rod Mod,BO White PTB,CAI/JRE Scoop, Moroso Catch Can GC Aluminum DS Stainless Works Ceramic LTH/HiFlo Cats SCT X4 Dynosteve, Hotckis 1" Springs & Chassis Max Brace BMR Adjustable Swaybars,Trailing Arms, Adjustable Toe Rod, LCA & Z28 UCA Bushings Hendrix Solid Cradle Bushings Pedders Radius Rod Inserts Strut tower brace Hero Smoked Tail and 3rd Brake Light, Diode Dynamic SL1 Fog Lights AeroForce Dual gauge/Autometer pillar mount. |
07-03-2022, 12:32 PM | #7 |
not afraid of the wall
Drives: Camaros Join Date: Apr 2010
Location: Pittsburgh
Posts: 2,148
|
I’ve also been using Super Lube for years. It works great with everything. The drylube spray is great for getting into spots you can’t reach as well.
__________________
2023 1LE 1SS BCD GCF JF5 MN6 SIA SLN UQT
10/13/22: 1100 Past Camaros: 13 1LE|02 SS|01 Z28|00 SS|91 1LE|91 Z28|89 IROC-Z |
07-03-2022, 09:04 PM | #8 |
Drives: 2014 2SS/RS 6SP Ashen Grey Join Date: Aug 2021
Location: NY
Posts: 1,264
|
Spraying the End Links did not help, It sounds like the springs to me but they are new with the noise pieces on them.
__________________
GM 3.91/TrueTrac OEM ZL1 Rims, Brakes & Side Skirts.ACST4 Splitter/Deflectors NPP M2W,GM Short Throw,Remote Clutch reservoir
GPI Ported Rod Mod,BO White PTB,CAI/JRE Scoop, Moroso Catch Can GC Aluminum DS Stainless Works Ceramic LTH/HiFlo Cats SCT X4 Dynosteve, Hotckis 1" Springs & Chassis Max Brace BMR Adjustable Swaybars,Trailing Arms, Adjustable Toe Rod, LCA & Z28 UCA Bushings Hendrix Solid Cradle Bushings Pedders Radius Rod Inserts Strut tower brace Hero Smoked Tail and 3rd Brake Light, Diode Dynamic SL1 Fog Lights AeroForce Dual gauge/Autometer pillar mount. |
|
|
|
|