09-12-2020, 02:45 PM | #1 |
Drives: 2019 Zl1 Join Date: Aug 2016
Location: Lancaster Pennsylvania
Posts: 100
|
BC FORGED wheels, tires
New wheels and tires from Pkautodesign
BC Forged 2 piece 305/30/19 Fronts 325/30/19 Rears ZLE specs 5mm front spacers 3mm rear spacers Not sure about the spacers yet.
__________________
|
09-12-2020, 02:51 PM | #2 |
Drives: Big Dually ... RIP ZL1 Join Date: May 2020
Location: Nearest (diesel) station
Posts: 218
|
The blue cyclone special
__________________
Imagine impulsively buying a Summit ZL1.
|
09-12-2020, 02:55 PM | #3 |
Drives: 2010 Camaro SS 2011 Mustang GT Join Date: Apr 2011
Location: Huntington WV
Posts: 356
|
For sale?
Sent from my SM-N960U using Tapatalk |
09-12-2020, 03:02 PM | #4 |
Drives: 18 ZL1 nightfall grey A10 Join Date: Apr 2018
Location: RGV Texas
Posts: 1,527
|
If you don’t need the spacers, I would take them off. Unless you didn’t factor in the correct offset for the wheels?
BC makes amazing wheels. Those are a bit busy but if you dig them that’s awesome! |
09-12-2020, 03:22 PM | #5 |
Drives: 2010 IBM 1SS (Former) Join Date: Feb 2009
Location: NoVA
Posts: 2,032
|
These are fully modular, so they shouldn't need spacers... I am wondering if these were for a different application and just happened to fit the ZL1. They do make beautiful wheels though.
|
09-12-2020, 03:31 PM | #6 |
Drives: 2010 Camaro SS 2011 Mustang GT Join Date: Apr 2011
Location: Huntington WV
Posts: 356
|
I love my bc wheels. No spacers
Sent from my SM-N960U using Tapatalk |
09-12-2020, 03:46 PM | #7 |
Drives: 18 ZL1 nightfall grey A10 Join Date: Apr 2018
Location: RGV Texas
Posts: 1,527
|
BC Forged are top quality for sure
|
09-12-2020, 04:50 PM | #8 |
Drives: 2019 Zl1 Join Date: Aug 2016
Location: Lancaster Pennsylvania
Posts: 100
|
The only reason I used spacers is because of reading about rubbing in the front and rear wiring . These where made for my zl1. I will try removing them.
__________________
|
09-12-2020, 05:37 PM | #9 |
Drives: 18 ZL1 nightfall grey A10 Join Date: Apr 2018
Location: RGV Texas
Posts: 1,527
|
The wire harness on the ZL1 is the same as the one on the ZLE so there is no difference there. There is a difference in the front suspension so a small spacer might be needed. I would remove the rear spacer and put that one in the front so it’s not too pushed out but enough to clear suspension if needed.
|
09-12-2020, 07:38 PM | #10 |
Drives: 18 ZL1 1LE Join Date: Apr 2013
Location: Florida
Posts: 703
|
If you’re buying custom wheels why wouldn’t you just buy the offsets you need for your car?
|
09-12-2020, 07:56 PM | #11 |
|
Those look fun to clean.
__________________
2017 ZL1 A10: 8.84 @ 156 PB
2017 ZL1 A10: Previously FBO 756/761 (9.6 @ 143 1/4) SOLD-2013 ZL1 M6:BTR,LTs,IDs,ATI,RotoFab10.84@129 SOLD-2011 SS M6: Blower, Cam, Alky, LTs. |
09-12-2020, 09:45 PM | #12 |
Drives: 2019 Chevy Camaro ZL1 M6 Join Date: Jul 2019
Location: Sea level
Posts: 1,252
|
|
09-12-2020, 11:34 PM | #13 |
Drives: ZL1 1LE Join Date: Oct 2018
Location: NYC (almost)
Posts: 339
|
|
09-13-2020, 05:41 AM | #14 |
Drives: 2010 Camaro SS 2011 Mustang GT Join Date: Apr 2011
Location: Huntington WV
Posts: 356
|
|
|
|
Post Reply
|
|
|