You are browsing camaro6 
11-17-2023, 06:25 PM
|
#1 |
 
Drives: 2020 Camaro SS 1LE | Satin Steel Join Date: Jan 2022
Location: Lubbock, Tx
Posts: 145
|
Johnson 2110r + stock compression = ? pushrod length
I Haven't ordered any parts yet but I'm think about doing H/C from GPI. I plan to run Johnson 2110r's, stock head gasket, no milling and I'm just wondering if anyone with this exact setup could tell me what pushrod length I will need. I have no problem measuring but it would be very convenient if I didn't have to.
__________________
GPI SS3 / GPI ported heads | MSD Atomic / NW 103mm | 1 7/8th LTH | Roto-Fab CAI | FlexFuel | Tuned by GPI |
xxx Hp / xxx tq |
|
|
|
12-08-2023, 02:01 PM
|
#2 |
|
Drives: 2020 Camaro SS 1LE | Satin Steel Join Date: Jan 2022
Location: Lubbock, Tx
Posts: 145
|
I guess no one knows, huh?
__________________
GPI SS3 / GPI ported heads | MSD Atomic / NW 103mm | 1 7/8th LTH | Roto-Fab CAI | FlexFuel | Tuned by GPI |
xxx Hp / xxx tq |
|
|
|
|
12-08-2023, 02:16 PM
|
#3 |
 Drives: 2020 Rally Green ZL1-1LE Join Date: May 2020
Location: Illinois
Posts: 344
|
This isnt something you want to guess at based off someone elses setup, ESPECIALLY with running a short travel lifter. You have to measure.
|
|
|
|
|
12-08-2023, 03:15 PM
|
#4 | |
          
Drives: 2017 Camaro 2SS A8 Join Date: Aug 2018
Location: Petersham MA
Posts: 4,809
|
Quote:
__________________
2017 Chevy Camaro 2SS A8 Whipple 3.0, Mast Black Label heads, Fore triple in-tank pumps, 112mm TB, LPE +52% injectors, LPE BB HPFP, 15” conversion 1059 WHP/944 WTQ, 9.48@150
|
|
|
|
|
|
12-08-2023, 07:54 PM
|
#5 |
Drives: 2016 Camaro Join Date: Oct 2017
Location: Texas & Uncle Sam's Choice
Posts: 123
|
What did Gwatney say when you asked?
__________________
2024 Chevrolet 3500HD Z71, LTZ, 4x4, 6.6 ltr. L5P long-bed.
2016 Camaro 2SS Six-speed, Hotchkis sway bars, Eibach .750" drop springs, Mamo throttle body, E85, BMR stuff. 2006 Quicksilver 6-speed GTO ERL LS3-430, All-Pro 285cc heads, 262/273 .758/.742 116+3 cam, Sheet-metal Intake, 70lb Siemens injectors, SLP, GMM Ripshifter, QA1 Coil-overs front and rear, nylon suspension bushings, Hotchkis, RPM Trans, SPEC twin clutch, SpinTech, Kooks 1 7/8 -2.0", BMR drive train, Kaaz 3.91, Lingenfelter CAI, Baer brakes, mini-tubs, E85. |
|
|
|
|
12-08-2023, 08:06 PM
|
#6 |
|
Drives: 2020 Camaro SS 1LE | Satin Steel Join Date: Jan 2022
Location: Lubbock, Tx
Posts: 145
|
They said that they thought 7.850, but they weren't sure. I figure if someone is running the exact same setup (head gasket, head milling spec, cam, lifters, springs) the pushrod measurement should be the same.
__________________
GPI SS3 / GPI ported heads | MSD Atomic / NW 103mm | 1 7/8th LTH | Roto-Fab CAI | FlexFuel | Tuned by GPI |
xxx Hp / xxx tq |
|
|
|
|
|
|
|
|
Post Reply
|
|
|
