05-13-2015, 09:26 AM | #15 |
Kyle 1LE
Drives: 2015 Camaro 1LE black Join Date: Jan 2015
Location: New Jersey
Posts: 183
|
http://www.amazon.com/gp/product/B00...?ie=UTF8&psc=1
Just ordered these! Fingers crossed but for $40.00 kinda hard to pass on |
05-13-2015, 01:30 PM | #16 | |
Drives: 2015 2SS, 1LE, Dual Mode, Black Join Date: Aug 2014
Location: Central Florida
Posts: 73
|
Quote:
|
|
05-13-2015, 01:32 PM | #17 | |
Drives: 2015 2SS, 1LE, Dual Mode, Black Join Date: Aug 2014
Location: Central Florida
Posts: 73
|
Quote:
|
|
05-13-2015, 02:15 PM | #18 |
Drives: Black 2018 Camaro ZL1 auto Join Date: Nov 2012
Location: Atlanta GA
Posts: 282
|
__________________
2018 ZL1 A10 with PTB, ROTOFAB, Pulley and tune from
Vengeance. 607 rwhp/647 rwtq |
05-13-2015, 02:18 PM | #19 |
Drives: Black 2018 Camaro ZL1 auto Join Date: Nov 2012
Location: Atlanta GA
Posts: 282
|
another one I found on craigs list
http://boone.craigslist.org/pts/5006512526.html
__________________
2018 ZL1 A10 with PTB, ROTOFAB, Pulley and tune from
Vengeance. 607 rwhp/647 rwtq |
05-13-2015, 03:28 PM | #20 |
|
race ramps 67inch.
|
05-13-2015, 05:21 PM | #21 |
Drives: 2011 2SS/RS M6 VR Join Date: Aug 2011
Location: Chicagoland
Posts: 1,536
|
+1 I have those and I'm lowered. Worked great for loading on my trailer too.
__________________
|
05-13-2015, 06:20 PM | #22 |
Call Me"Doc"
Drives: 2014 2SS/RS 1LE BLACK Join Date: Apr 2009
Location: Ft Riley, Kansas
Posts: 890
|
A jack and jack stands work for anything...
|
05-13-2015, 06:29 PM | #23 |
But not just any jack. I got this at Harbor Freight and it is low enough to roll under the splitter, and long enough to reach the subframe. Works like it was made for the 1LE.
http://www.harborfreight.com/2-ton-l...ump-60678.html
__________________
Past: '69 Chevelle SS396 '79 Camaro 400SBC/TH400 Present: '14 Camaro 2SS/1LE '03 Avalanche (tow car for...) Twin-turbo SBC Super Comp Dragster Future: FFR 33 Hot Rod w/ SBC RCR GT-40 w/ LS7 |
|
05-13-2015, 07:06 PM | #24 |
Drives: 2014 Camaro 2SS/RS 1LE Join Date: Oct 2013
Location: Durham NC
Posts: 82
|
The 67" Race (2 pc)...you will not be disappointed. Pricey but well worth the investment! Also the the 10"X12" wheel cribs, if this is within your budget. If not, the other idea's mentioned to save money.
As backeddy stated: CHOCKS for safety always!! Brent
__________________
'14 Camaro 2SS/RS 1LE
'96 Impala SS '69 Camaro Convertible |
05-13-2015, 07:14 PM | #25 |
Drives: SS 1LE Join Date: Nov 2012
Location: Texas
Posts: 1,829
|
Do you all think the 56 race ramps would clear the splitter?
|
05-13-2015, 07:44 PM | #26 | |
Drives: 2014 Camaro 2SS/RS 1LE Join Date: Oct 2013
Location: Durham NC
Posts: 82
|
Quote:
I think that the 67" was recommended plus the 67" is 14" wide and 10" in height where the 65" are 12" wide and 8" in height. I think someone on this forum has used the 56" but go with the 67" if you can. Their 2 piece and very light weight. Hope this helps. Check out the site and you will be able to make an informed decision. Brent
__________________
'14 Camaro 2SS/RS 1LE
'96 Impala SS '69 Camaro Convertible |
|
05-13-2015, 08:22 PM | #27 |
Kyle 1LE
Drives: 2015 Camaro 1LE black Join Date: Jan 2015
Location: New Jersey
Posts: 183
|
Good catch didn't look at the width! Thanks
|
05-14-2015, 07:29 PM | #28 |
Drives: 2015 2SS, 1LE, Dual Mode, Black Join Date: Aug 2014
Location: Central Florida
Posts: 73
|
Do the test using the technique on Race Ramps website using a yard stick. That will give you the answer. I am looking at only the ones that lift 10" and are at least 12" wide. They have a couple that meet that criteria.
Last edited by Sidecardog1; 05-14-2015 at 07:32 PM. Reason: Update |
|
|
Thread Tools | |
|
|