Homepage Garage Wiki Register Social Groups Calendar Search Today's Posts Mark Forums Read
#Camaro6
Go Back   CAMARO6 > Technical Camaro Topics > Camaro DIY & HOW-TO instructions & discussions


Phastek Performance


Post Reply
 
Thread Tools
Old 03-10-2019, 05:30 PM   #1
Gasoline_Farts
 
Drives: 19 SS 1LE
Join Date: Nov 2018
Location: NV
Posts: 140
DIY: 2019 "flow-tie" removal

In the 1LE delivery thread someone photoshopped a black flowtie onto a 2019. I looked for instructions on getting into the bumper but only found vague information about the radiator shroud removal. Here is what I did:

Tools:
• 10mm socket
• 13mm socket
• Long extensions
• T30H
• T15H
• Flathead Screw driver (or something to pry with)
• Mirror on a stick (with lights even better)
• Magnet (never know when you’ll drop something


1) Remove the following (1.jpg):
a. 4x 10mm bolts (yellow dots)
b. 6x T15H torx (red dots)
c. 2x T30H torx (purple dots)
d. Two rubber hood stops – count how many turns required so you can put them back at the same height (green dots)
Your shroud is now loose, however the hood latch is in the way for removal. Luckily it is very easy to remove.




2) Using your extensions and 13mm socket remove the hood latch bolts through the front grill. Once the bolts are out, just let it hang down. It might be a good idea to mark it off before you remove it so that you can put it back in exactly the same place
(3.jpg and 4.jpg)






3) Slide the radiator shroud towards the engine and slightly upwards, it should slide out with a bit of effort (5.jpg)





4) You can now access the back of the flowtie where it attaches to the bumper. Using a screwdriver or your pry tool and mirror gently pry each tab while pulling gently from the front, this was the most delicate and longest part of the job. There are 6 pins holding it in, however it was only the left and right sides I needed to work on, the top and bottom came out on their own. (7.jpg, 8.jpg)






5) Done. Now you can paint it and while you wait for it to dry, put everything back together. Since when you are done you can just press it back into the bumper. (9.jpg, 10.jpg)

Gasoline_Farts is offline   Reply With Quote
Old 03-10-2019, 07:30 PM   #2
FollowMyLine
Driver for Hire
 
FollowMyLine's Avatar
 
Drives: 22 Camaro 2SS 1LE M6
Join Date: Jul 2017
Location: Mayer, MN
Posts: 661
That was me that has been photoshopping the flow tie since I thought I might be buying a 2019. I ended up finding a 2018 Hyper Blue, and posted that picture in the other thread. Can’t wait to see the final result!
FollowMyLine is offline   Reply With Quote
Old 03-10-2019, 07:50 PM   #3
Gasoline_Farts
 
Drives: 19 SS 1LE
Join Date: Nov 2018
Location: NV
Posts: 140
It’s very cold here so it might be tomorrow before the paint dries, I’ll likely get a nice pic next weekend after it’s washed
Gasoline_Farts is offline   Reply With Quote
Old 03-11-2019, 10:39 AM   #4
Gasoline_Farts
 
Drives: 19 SS 1LE
Join Date: Nov 2018
Location: NV
Posts: 140
took a cellphone pic this morning:


Gasoline_Farts is offline   Reply With Quote
Old 03-11-2019, 12:18 PM   #5
FollowMyLine
Driver for Hire
 
FollowMyLine's Avatar
 
Drives: 22 Camaro 2SS 1LE M6
Join Date: Jul 2017
Location: Mayer, MN
Posts: 661
Quote:
Originally Posted by Gasoline_Farts View Post
took a cellphone pic this morning:


So. Much. Better. Looks great!
FollowMyLine is offline   Reply With Quote
Old 03-13-2019, 01:55 PM   #6
chozn4service


 
chozn4service's Avatar
 
Drives: 2016 SS w/2SS A8 Blue Velvet
Join Date: Dec 2009
Location: 39.793153,-86.238223
Posts: 3,678
So essentially the OP removed the chrome trim around the flowtie? Looks much better but now my question is the open tabs around the frame of the bowtie. Will you have a body shop plastic weld a piece in there, smooth it out and shoot it?
That piece in the bumper just looked out of place to me and I thought they (GM) might correct it before final roll out since it was met with such disdain.
Good deal on making it yours....
__________________
Never grow up, it's a trap!
chozn4service is offline   Reply With Quote
Old 03-13-2019, 02:31 PM   #7
FollowMyLine
Driver for Hire
 
FollowMyLine's Avatar
 
Drives: 22 Camaro 2SS 1LE M6
Join Date: Jul 2017
Location: Mayer, MN
Posts: 661
Quote:
Originally Posted by chozn4service View Post
So essentially the OP removed the chrome trim around the flowtie? Looks much better but now my question is the open tabs around the frame of the bowtie. Will you have a body shop plastic weld a piece in there, smooth it out and shoot it?
That piece in the bumper just looked out of place to me and I thought they (GM) might correct it before final roll out since it was met with such disdain.
Good deal on making it yours....
Removed it, painted it, and put it back on, unless I’m mistaken.
FollowMyLine is offline   Reply With Quote
Old 03-13-2019, 03:36 PM   #8
Gasoline_Farts
 
Drives: 19 SS 1LE
Join Date: Nov 2018
Location: NV
Posts: 140
Quote:
Originally Posted by M0DRN71 View Post
Removed it, painted it, and put it back on, unless I’m mistaken.
you are correct.
removed, painted, reinstalled.

ill try to get a close up photo of the final job this weekend.
Gasoline_Farts is offline   Reply With Quote
Old 03-31-2019, 09:53 AM   #9
Grey1LE
 
Drives: 2019 Camaro SS 1LE
Join Date: Mar 2019
Location: Apex NC
Posts: 65
Awesome post, I'll be doing mine when I get the car back from ceramic coating!!
Grey1LE is offline   Reply With Quote
Old 04-02-2019, 05:33 PM   #10
z28pat

 
z28pat's Avatar
 
Drives: 2002 z28, 2018 2ss 1LE
Join Date: Sep 2012
Location: Parrish, Florida
Posts: 832
That sema concept car with the bow tie moved and the front strip painted body color was so much better looking. Let us know how this turns out when it's done, I'm interested to see it
Thanks
z28pat is offline   Reply With Quote
Old 04-08-2019, 12:30 PM   #11
Infamus
 
Infamus's Avatar
 
Drives: 2018 Camaro ZL1
Join Date: Feb 2019
Location: FL
Posts: 345
Great post! time to get mine done.
Infamus is offline   Reply With Quote
Old 06-07-2019, 09:32 AM   #12
overdriv
 
overdriv's Avatar
 
Drives: 1969 Chevelle SS 2019 2SS Camaro
Join Date: Jul 2018
Location: IL
Posts: 246
Does anyone know if someone makes a gold bow tie emblem for the 2019 that would replace the flowtie?
overdriv is offline   Reply With Quote
Old 04-12-2020, 02:07 PM   #13
GermanMuscle
 
Drives: 2019 Camaro 1SS 1LE
Join Date: Mar 2018
Location: Fort Myers, FL
Posts: 103
Been wanting to do this for awhile and Covid 19 presented itself as a good opportunity! Thanks OP for original post.
Sorry for the dirty car, I was sweating A LOT it was 94 in Florida today.
Attached Images
 
GermanMuscle is offline   Reply With Quote
Old 04-13-2020, 03:28 PM   #14
gmcvt
 
gmcvt's Avatar
 
Drives: 2019 Camaro 1SS A10
Join Date: Nov 2015
Location: Tn
Posts: 465
I removed and blackened mine also, looks much better . But, I just used a plastic trim panel tool and carefully popped it out. No damage. Took about a minute to do.
__________________
"Jesus said to them: I am the way, the truth and the life and no one comes to the Father except through me" John 14:6
2020 Mustang GT M6
2019 Camaro 1SS A10 E85/Pray tuned & ported IM/TB.**SOLD**
2018 Mustang GT A10 Kooks Lt's, E85 & Lund tune*SOLD*
2010 Camaro 2SS/RS M6 Silver- CAI, Bo-body, VRSP-2 cam, Kooks 1 7/8 Lt's w/cats, Magnaflow street CB(15089), QTP ovals, Elite can, Vengeance Racing tune. *SOLD*

Last edited by gmcvt; 04-14-2020 at 10:46 AM.
gmcvt is offline   Reply With Quote
 
Post Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:08 AM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.