09-05-2019, 11:48 AM | #1 |
Drives: 2017 2SS M6 Join Date: Jun 2013
Location: WNY
Posts: 7,070
|
Torque to yield bolt number thread TTY bolts
Im hoping to get this stickied so we have a list of bolt numbers. I will add non tty bolts to. please dont reply to this thread unless you have part numbers for me. thanks part numbers are in post #2
__________________
real ZL1 wheels and brakes, 285/305 Michelin Pilot Super Sports, Pray ported Intake manifold, Soler Throttle Body, Rotofab intake, EFI Tuning Flex fuel kit, full American Racing Headers Exhaust, 1 7/8" w/ cats H pipe and mufflers. Full 1LE suspension, with BMR adjustable sway bars and links, GM aluminum cradle bushings, Hurst shifter with lighter reverse spring, TWM shifter knob, Tick level 1 transmission. I should have bought a ZL1
|
09-05-2019, 12:00 PM | #2 |
Drives: 2017 2SS M6 Join Date: Jun 2013
Location: WNY
Posts: 7,070
|
Caliper Bolts (SS, SS/1LE, ZL1, ZL1/1LE) reusable GM says you have to replace them but then they say you can reuse them in the performance sections.
front #11611085 rear#11570091 __________________________________________________ __________________________________________________ _____________________________ Alignment bolts TTY 11547215 Lower Control Arm Bolt, Left INNER 11547215 Lower Control Arm Bolt, Right INNER 11547262 Lower Control Arm Washer, Left and right the bolts in your car may be different but these are the replacements. you will need this washer to go on the replacement LCA BOLTS. 11611276 Link Rod Bolt, Right INNER 11611276 Link Rod Bolt, Left INNER YOU CAN REUSE THE WASHERS AND NUTS WITH BLUE LOCTITE __________________________________________________ __________________________________________________ _____________________________ Rear cradle bolts front 11547921 qty 2 rear 11611819 qty 2 __________________________________________________ __________________________________________________ _____________________________ ill finish this later
__________________
real ZL1 wheels and brakes, 285/305 Michelin Pilot Super Sports, Pray ported Intake manifold, Soler Throttle Body, Rotofab intake, EFI Tuning Flex fuel kit, full American Racing Headers Exhaust, 1 7/8" w/ cats H pipe and mufflers. Full 1LE suspension, with BMR adjustable sway bars and links, GM aluminum cradle bushings, Hurst shifter with lighter reverse spring, TWM shifter knob, Tick level 1 transmission. I should have bought a ZL1
Last edited by JCunningham; 09-20-2019 at 11:41 PM. |
09-05-2019, 12:37 PM | #3 |
Drives: 2013 Camaro 1LE Join Date: Jul 2012
Location: Verona, WI
Posts: 1,924
|
Would be nice to include the torque specs with these bolt part numbers too as people are always looking for the torque spec. Just a thought while the list is still small and easier to update/add info.
__________________
|
09-05-2019, 09:52 PM | #4 |
Drives: 2017 2SS M6 Join Date: Jun 2013
Location: WNY
Posts: 7,070
|
YES THANK YOU
__________________
real ZL1 wheels and brakes, 285/305 Michelin Pilot Super Sports, Pray ported Intake manifold, Soler Throttle Body, Rotofab intake, EFI Tuning Flex fuel kit, full American Racing Headers Exhaust, 1 7/8" w/ cats H pipe and mufflers. Full 1LE suspension, with BMR adjustable sway bars and links, GM aluminum cradle bushings, Hurst shifter with lighter reverse spring, TWM shifter knob, Tick level 1 transmission. I should have bought a ZL1
|
09-06-2019, 08:01 AM | #5 |
|
J6M (SS 1LE) front caliper bolts are TTA. They can be reused per the service manual, I've done it. Follow the procedure in the manual. Although if you do a lot of caliper removals I would replace them every so often since they are not that expensive, especially if tracking a lot which I do.
J6M (SS 1LE) front caliper bolts = 11570092 Torque first pass to 150N-m or 111 lb-ft Second pass 15-30 degrees |
09-20-2019, 11:36 PM | #6 |
Drives: 2017 2SS M6 Join Date: Jun 2013
Location: WNY
Posts: 7,070
|
the dealer gave me 11611085 for the fronts for a 17 ZL1
__________________
real ZL1 wheels and brakes, 285/305 Michelin Pilot Super Sports, Pray ported Intake manifold, Soler Throttle Body, Rotofab intake, EFI Tuning Flex fuel kit, full American Racing Headers Exhaust, 1 7/8" w/ cats H pipe and mufflers. Full 1LE suspension, with BMR adjustable sway bars and links, GM aluminum cradle bushings, Hurst shifter with lighter reverse spring, TWM shifter knob, Tick level 1 transmission. I should have bought a ZL1
|
03-21-2020, 02:36 PM | #7 |
Geoff
Drives: 2020 ZL1 Green Join Date: May 2013
Location: Houston
Posts: 1,720
|
2020 ZL1
Front Caliper Bolt GM 11570092, 111lb-ft then 15-30 degrees Rear Caliper Bolt GM 11570091, 92lb-ft For both clean threads, use GM 89021297 threadlocker (red)
__________________
|
|
|
Post Reply
|
|
|