![]() |
#1 |
![]() ![]() |
Relocating Wire Harness for Larger Tires
Someone asked for a summary of how to do the wire harness relocation for the driver side rear wheel well when upgrading to larger tires. I uploaded this summary and picture and figured I would share here:
Here's a picture of my driver side rear wheel well. After you remove the wheel well liner you should see a cable that runs in the general path of the red line. - Remove the wheel well liner by popping out the handful of plastic clips (I only undid the forward half of the liner) - The yellow marks represent where the cable is secured with a zip tie, - Cut the bottom 2 that are shown - Relocate the cable by sliding it inboard as far as it goes (shown by the green line) - Down at the bottom by the harness connector you will see a frame with a hole that you can run a zip tie through to secure it in it's new location You can see in the picture where the hole will form from rubbing. This particular picture is from a BFG 305/35/20 on stock springs. Why did I go with a 35 instead of a 30... Because that's all the BFG comp 2 A/S comes in and I wanted to run a 305 size A/S on my 20x11s. After a few hundred miles the rubbing stopped (didn't get any bigger than what you see below) and no issues with damage to the cable. |
![]() |
![]() |
![]() |
#2 |
![]() Drives: 2018 Camaro ZL1 Join Date: Jul 2016
Location: Cali
Posts: 100
|
Thanks for the write up and Pic!!!!
|
![]() |
![]() |
![]() |
#3 |
![]() ![]() |
|
![]() |
![]() |
![]() |
#4 |
![]() ![]() ![]() ![]() Drives: SS-6-SPD Join Date: Jan 2017
Location: New Jersey
Posts: 1,376
|
Perfect!!!!
Thanks JATT |
![]() |
![]() |
![]() |
#5 |
![]() ![]() |
|
![]() |
![]() |
![]() |
#6 |
![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() Drives: 2016 Hyper Blue 1SS Join Date: Jul 2015
Location: hampton roads
Posts: 2,763
|
Going to wide for track lol. I had to rerouute the wire today
__________________
1ss/Auto-Hyper Blue
acs carbon flash spoiler, bmr springs, gm clear tails. Texas speed cam, 223/227 .635/.635 116 LSA, Kooks Long Tube Headers with green cats, MSD Atomic Air Force Intake, CAI Cold Air Intake, QTP cutouts. 503 hp Best so far 11.5 at 123 with a 1.83 60ft. BMR lower and upper trailing arms and upper control arms,E85 DELIVERED 12/29/15 http://youtube.com/bybcous " no talking only racing on my youtube" |
![]() |
![]() |
![]() |
#7 |
![]() ![]() |
|
![]() |
![]() |
![]() |
#8 |
Lethal Camaro
Drives: 16 2SS, 71 Std, Suburban RTS Join Date: Jun 2013
Location: Temecula, CA
Posts: 3,855
|
How wide did you go?
__________________
|
![]() |
![]() |
![]() |
#9 |
![]() Drives: 2017 Camaro SS 1LE HBM Join Date: Feb 2017
Location: Toronto
Posts: 28
|
Is this already done at the factory for 1LE SS ?
Mr Al |
![]() |
![]() |
![]() |
#10 |
![]() ![]() ![]() ![]() Drives: 2018 ZL1 A10 Join Date: May 2012
Location: British Columbia, Canada
Posts: 1,372
|
Hmmm...was this changed for the 2018 ZL1?
__________________
DAVENPORT STAGE 2 PLUS - 2" ARH ceramic coated headers - 3" ARH catless exhaust - Stock NPP mufflers - Kong ported SC - Katech 103 ported TB - Rotofab 5" Big gulp CAI - 22.5% lower pulley - ATI Harmonic balancer - Cordes SC expansion tank - MSD hi temp ignition wires - Koolsox spark plug insulators - custom tunes - 660hp/725tq pump - 713hp/763tq race
|
![]() |
![]() |
![]() |
#11 |
Chin Event Manager
Drives: 2018 SS 1LE Join Date: Dec 2011
Location: Bradenton FL
Posts: 50
|
I'm gonna say no because mine is wearing through the liner right at that spot and i't completely stock.
__________________
Jim Pomroy
Chin Track Days Chief Instructor and Event Manager 2018 1LE 2015 Mustang GTPP 2011 Duramax Access to several Chin track cars... |
![]() |
![]() |
![]() |
#12 |
![]() Drives: 2017 50th Camaro SS Join Date: Jul 2016
Location: Maryland
Posts: 525
|
Just relocated mine last night before mounting 305/45/17 Mickeys for the track.
__________________
50th Anniversary Edition |Borla Atak and 60606 mid pipes| Kooks 1 7/8" | ProCharger Stage II |305/45/17 DRs | Circle D 3500 stall | LT4 fueling | Custom made Lowside Aux Pump | Alky Control Meth | DSX E85
|
![]() |
![]() |
![]() |
#13 |
![]() ![]() ![]() Drives: 2019 zl1 6 speed Join Date: Jul 2017
Location: Lake Havasu Arizona
Posts: 1,020
|
I took my wheel off and did the wire reloaction as directed above. Then I went down to discount tire, after a sweet burnout of course, and had some ps4's installed. (295 in the back)Upon receiving the car, discount tire said it was rubbing the fender well a little bit. So I went home, pulled off my tire and peeled the liner back, cleaned a couple spots on the frame with alcohol, and stuck velcro to the car, then peeled the other side and stuck it to it. I then put the liner back and pressed where the velcro was. I gained maybe an inch of space as there was a gap between the liner and the car. I can now get my fingers behind the tire where before I couldn't. Figured this might help some people from preventing holes in their liner.
|
![]() |
![]() |
![]() |
#14 |
![]() Drives: 2017 Camaro 1LE SS Join Date: Oct 2016
Location: In my driveway or on the track. Lol
Posts: 257
|
No. Had to relocate mine. It’s simple.
|
![]() |
![]() |
|
|
Post Reply
|
|
|