Homepage Garage Wiki Register Social Groups Calendar Search Today's Posts Mark Forums Read
#Camaro6
Go Back   CAMARO6 > Engine | Drivetrain | Powertrain Technical Discussions > Forced Induction Discussions


BeckyD @ James Martin Chevy


Post Reply
 
Thread Tools
Old 04-18-2019, 11:19 AM   #29
EDFHOBBIES
Dyno Show Queen LOL
 
EDFHOBBIES's Avatar
 
Drives: 16 SS & 17 ZL1 Both Yellow
Join Date: Jan 2014
Location: Houston
Posts: 4,343
Send a message via Skype™ to EDFHOBBIES
Robert says he had a 2650. But the shaft broke on it. He also says he has a 2300r.. not sure why he feels the need to fib.. anyhow glad I know the truth ty for answering me I'm gonna block that guy no need to brag about stuff u dont have.. he also claims hes at 960 on the 2300 as well on e85 no meth.. he has just said he has a 2300 now. With out the port injection I dont see that number happening..
Attached Images
 
__________________


Kong Ported 2650, Crawford Racing Port Injection, Weapon X 112mm Adapter, NW112mm TB, Livernois Ported LT4 Heads, Lingenfelter GT32 stealth cam, Haltech Elite, and Carbon by Trufiber
EDFHOBBIES is offline   Reply With Quote
Old 04-18-2019, 11:24 AM   #30
ShizzySupra
 
Drives: 16' Camaro 2SS
Join Date: Sep 2015
Location: Oregon
Posts: 381
Dead giveaway right there. The 2300R is EXACTLY the same outside physically as any other 2300 for Gen6’s. Its internal differences that are VERY apparent when you see them compared side by side...


Quote:
Originally Posted by EDFHOBBIES View Post
Robert says he had a 2650. But the shaft broke on it. He also says he has a 2300r.. not sure why he feels the need to fib.. anyhow glad I know the truth ty for answering me I'm gonna block that guy no need to brag about stuff u dont have.. he also claims hes at 960 on the 2300 as well on e85 no meth.. he has just said he has a 2300 now. With out the port injection I dont see that number happening..
__________________
@DeathWatchCamaro on Insta
993whp Magnuson 2.3R
9.5 @ 145, Magnuson 2300, Full Weight 2SS, 17’s (810whp)
ShizzySupra is offline   Reply With Quote
Old 04-18-2019, 11:28 AM   #31
ShizzySupra
 
Drives: 16' Camaro 2SS
Join Date: Sep 2015
Location: Oregon
Posts: 381
Also I just checked my messages, he tends to not lie to me since I track times to back up everything, most he said he ever made was 843 (never showed dynograph) and his is manual. But he said the best they could get it to trap was 129. He also said IAT2’s were 168... so the car needs Jesus no matter WHAT blower is on it.
__________________
@DeathWatchCamaro on Insta
993whp Magnuson 2.3R
9.5 @ 145, Magnuson 2300, Full Weight 2SS, 17’s (810whp)
ShizzySupra is offline   Reply With Quote
Old 04-18-2019, 11:36 AM   #32
EDFHOBBIES
Dyno Show Queen LOL
 
EDFHOBBIES's Avatar
 
Drives: 16 SS & 17 ZL1 Both Yellow
Join Date: Jan 2014
Location: Houston
Posts: 4,343
Send a message via Skype™ to EDFHOBBIES
Thanks for the info I'm gonna steer clear of him.. he trys to create drama with Tony Moffett, Steve, Jacobs and some other big posters on FB gen 6 sites.

Anyway I wasn't putting Maggi down just wanted to know why the delay.

Thanks again.
__________________


Kong Ported 2650, Crawford Racing Port Injection, Weapon X 112mm Adapter, NW112mm TB, Livernois Ported LT4 Heads, Lingenfelter GT32 stealth cam, Haltech Elite, and Carbon by Trufiber
EDFHOBBIES is offline   Reply With Quote
Old 04-18-2019, 11:39 AM   #33
ShizzySupra
 
Drives: 16' Camaro 2SS
Join Date: Sep 2015
Location: Oregon
Posts: 381
Oh I didnt take it that way at all man! Good luck today with more tuning!

Quote:
Originally Posted by EDFHOBBIES View Post
Thanks for the info I'm gonna steer clear of him.. he trys to create drama with Tony Moffett, Steve, Jacobs and some other big posters on FB gen 6 sites.

Anyway I wasn't putting Maggi down just wanted to know why the delay.

Thanks again.
__________________
@DeathWatchCamaro on Insta
993whp Magnuson 2.3R
9.5 @ 145, Magnuson 2300, Full Weight 2SS, 17’s (810whp)
ShizzySupra is offline   Reply With Quote
Old 04-18-2019, 12:22 PM   #34
toohighpsi
 
Drives: 2015 C7 Z06 M7
Join Date: Dec 2012
Location: So-Cal
Posts: 651
Just to clear things up:

Speed Engineering has a Magnum DI TVS2650R with Katech fuel system on a C7 Z06 Corvette that makes 1002 RWHP
https://youtu.be/dnQ3uS4Nf-U

Mike Swanson has a TVS2300R with the Lingenfelter fuel system on his Camaro SS that makes 996 RWHP
https://youtu.be/YisA6Xno5bk

I'm not aware of any others.

To date, neither has had an 8-speed capable of handling the power that the cars make. ATI has recently released an upgraded 8-speed, Speed Engineering will be going that route. Not sure what Swanson has choosen.
toohighpsi is offline   Reply With Quote
Old 04-18-2019, 01:29 PM   #35
EDFHOBBIES
Dyno Show Queen LOL
 
EDFHOBBIES's Avatar
 
Drives: 16 SS & 17 ZL1 Both Yellow
Join Date: Jan 2014
Location: Houston
Posts: 4,343
Send a message via Skype™ to EDFHOBBIES
Those are good numbers.. if my fuel system can handle it I'll be right there. I doubt it will I did the 38 lobe instead of the 44 percent. I figured the 1500 pump would last a little longer on a smaller lobe.
__________________


Kong Ported 2650, Crawford Racing Port Injection, Weapon X 112mm Adapter, NW112mm TB, Livernois Ported LT4 Heads, Lingenfelter GT32 stealth cam, Haltech Elite, and Carbon by Trufiber
EDFHOBBIES is offline   Reply With Quote
Old 04-18-2019, 02:14 PM   #36
laynlo15
 
laynlo15's Avatar
 
Drives: 2022 Lt1 A10
Join Date: Nov 2015
Location: clark, mo
Posts: 8,857
I'm sure with the tranny slipping it probably cost him 2-3 tenths and lots of mph. That's unfortunate on Swanson. He called me from the track and told me what happened. Cost him a bunch of bucks for sure plus the heart ache of all the work he'd already put in it and put a pretty good scare to his wife and kids. Just talked to him again last night, it burnt the main harness and he was replacing that last night.
__________________
2022 Lt1 6.2 A10, Maggie 2300, THPSI Port Inj/10 rib, Rotofab, E, Nickey, SCOL, Griptech, RC Bandits, Hoosiers/MT 9.80@142.96 1.44 60ft, 6.34@112 707/669 RWHP/TRQ. 16SS Maggie 2650 9.41@147 1.35 60ft, 5.99@119. 16 C7 A8 10.90@128 Bolt on stuff
laynlo15 is offline   Reply With Quote
Old 05-14-2019, 10:43 PM   #37
SienarSystems
 
SienarSystems's Avatar
 
Drives: ZL1 1LE
Join Date: Oct 2018
Location: NYC (almost)
Posts: 339
Bump for the release date...it’s almost summer...
SienarSystems is offline   Reply With Quote
Old 05-15-2019, 06:05 AM   #38
laynlo15
 
laynlo15's Avatar
 
Drives: 2022 Lt1 A10
Join Date: Nov 2015
Location: clark, mo
Posts: 8,857
Soon
__________________
2022 Lt1 6.2 A10, Maggie 2300, THPSI Port Inj/10 rib, Rotofab, E, Nickey, SCOL, Griptech, RC Bandits, Hoosiers/MT 9.80@142.96 1.44 60ft, 6.34@112 707/669 RWHP/TRQ. 16SS Maggie 2650 9.41@147 1.35 60ft, 5.99@119. 16 C7 A8 10.90@128 Bolt on stuff
laynlo15 is offline   Reply With Quote
Old 05-15-2019, 12:06 PM   #39
Rlhay2
 
Rlhay2's Avatar
 
Drives: 2017 ZL1
Join Date: Mar 2014
Location: DFW, TX
Posts: 298
Saw this online over the weekend....
Attached Images
 
Rlhay2 is offline   Reply With Quote
Old 05-15-2019, 01:37 PM   #40
laynlo15
 
laynlo15's Avatar
 
Drives: 2022 Lt1 A10
Join Date: Nov 2015
Location: clark, mo
Posts: 8,857
yep
__________________
2022 Lt1 6.2 A10, Maggie 2300, THPSI Port Inj/10 rib, Rotofab, E, Nickey, SCOL, Griptech, RC Bandits, Hoosiers/MT 9.80@142.96 1.44 60ft, 6.34@112 707/669 RWHP/TRQ. 16SS Maggie 2650 9.41@147 1.35 60ft, 5.99@119. 16 C7 A8 10.90@128 Bolt on stuff
laynlo15 is offline   Reply With Quote
Old 05-15-2019, 06:57 PM   #41
SienarSystems
 
SienarSystems's Avatar
 
Drives: ZL1 1LE
Join Date: Oct 2018
Location: NYC (almost)
Posts: 339
Can anyone explain the coil relocation or new valvetrain covers listed above?
SienarSystems is offline   Reply With Quote
Old 05-16-2019, 11:47 AM   #42
Rlhay2
 
Rlhay2's Avatar
 
Drives: 2017 ZL1
Join Date: Mar 2014
Location: DFW, TX
Posts: 298
Quote:
Originally Posted by SienarSystems View Post
Can anyone explain the coil relocation or new valvetrain covers listed above?

2650 has larger rotors in larger cases in a confined space.
Rlhay2 is offline   Reply With Quote
 
Post Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:06 PM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.