08-22-2017, 11:20 AM | #15 |
Drives: 96SS Join Date: May 2009
Location: New Castle Delaware
Posts: 1,948
|
We typically use a 102 and even though that is technically 4.015 inches we have found increasing the diameter of the intake even over 4" inches has been beneficial regardless of the silicone reducer. We have seen increases over 4" to 4.5" and even more from 4.5" to 5". So regardless of people thinking the throttle body is smaller and can't possible help is false. Numbers haven't lied thus far.
|
08-22-2017, 05:45 PM | #16 |
Drives: 2012 ZL1 #1329 M6 Join Date: Jun 2009
Location: Reading, PA
Posts: 1,040
|
Definitely a nice piece. Might have to look into purchasing one of these. Could I run a ported 90mm Fran?
__________________
2012 Camaro ZL1 #1329 M6 Summit White
Built by Mike @ Rapid Motorsports 784rwhp 757 rwtq on 93 Octane ET - 10.97 @ 128 Heads-Blower-Snout-TB ported & prepared by Jeremy Formato of FasterProms http://www.camaro5.com/forums/showthread.php?t=395950 Rapid Motorsports 396ci Build https://www.camaro5.com/forums/showt...1#post10321301 10.832 @ 130.99 |
08-23-2017, 10:00 AM | #17 | |
Drives: 96SS Join Date: May 2009
Location: New Castle Delaware
Posts: 1,948
|
Quote:
Just when ordering note what size TB you have so we can send the right size reducer for your application. |
|
08-23-2017, 02:38 PM | #18 |
Sucker Punch
Drives: 2013 Black ZL1, 2007 Silverado LTZ Join Date: Jul 2014
Location: N.E. Ohio
Posts: 275
|
I have dual nozzles for my meth injection can that be done?
__________________
427 Dart SHP Pro LS Block, Callies Magnum Crank, Callies Ultra I Beam Rods, Diamond Pistons, AGP twin Turbos 6865, Mast heads, Cam Motion LLR cam, Morel tie bar lifters, Crower roller rockers, NW 103MM TB, ID2600 XDS, Fore Triple, DSX, E85, ARH Turbo Headers, Corsa, Jakes stage 5 4L80, Circle D, RPM Roll Bar, BMR, Carlyle Racing 15" conversion kit.
|
08-23-2017, 04:22 PM | #19 |
Drives: 96SS Join Date: May 2009
Location: New Castle Delaware
Posts: 1,948
|
|
08-23-2017, 05:12 PM | #20 |
Drives: 2012 ZL1 #1329 M6 Join Date: Jun 2009
Location: Reading, PA
Posts: 1,040
|
Appreciate the response Fran.
__________________
2012 Camaro ZL1 #1329 M6 Summit White
Built by Mike @ Rapid Motorsports 784rwhp 757 rwtq on 93 Octane ET - 10.97 @ 128 Heads-Blower-Snout-TB ported & prepared by Jeremy Formato of FasterProms http://www.camaro5.com/forums/showthread.php?t=395950 Rapid Motorsports 396ci Build https://www.camaro5.com/forums/showt...1#post10321301 10.832 @ 130.99 |
09-19-2017, 09:42 PM | #21 |
Drives: Camaro Join Date: Aug 2013
Location: Cali
Posts: 200
|
Fran is the IAT senor and bung necessary? Is this a stock sensor that the PCM uses? Meaning does this sensor unplug from the OE intake?
Are you willing to sell it non-coated so I can bring it to my powder coat guy to coat? And have no "RPM" logo? |
09-22-2017, 08:25 AM | #22 |
Drives: 2017 ZL1 A10 Join Date: Aug 2009
Location: Dubai
Posts: 1,250
|
Did anyone install this with alky control meth nozzle ?
Can we see some pics ? Ahmad
__________________
2017 ZL1 A10 SW (SOLD)
Whipple 2.9 with 3.2 Pulley, Weapon-X Stage 3 Cam, FIICHILLER ,LG Motorsports LT, Borla S type, ROTFAB Big Gulp, Big 3 Reservoir Glassskinz rear window valance . 2012 ZL1 A6 (SOLD) Forged 376 CI, LSA HeartBeat, Mast Medium Bore Heads & JDP ZLR Cam, ARH LT , MagnaFlow Resonated X + Borla Atak Catback, ADM 102mm Snout, CAI, NW102MM TB, ID850, Fore Triple Fuel Pump, MSD Wire's, Moroso CC. Alky Control, FIICHILLER. |
09-22-2017, 09:36 AM | #23 |
Drives: 2011 Camaro SS Join Date: May 2014
Location: NY
Posts: 180
|
Any plans for creating one for those of us with SS's with a maggy TVS?
|
10-25-2017, 05:04 AM | #24 |
Drives: 2017 ZL1 A10 Join Date: Aug 2009
Location: Dubai
Posts: 1,250
|
Bad Customer support
I never thought of writing this but I had to do it this time .
I ordered this intake for my HeartBeat supercharged ZL1 & requested a meth bung & unfortunately you have to get it with 2 bungs (IAT & Meth ) or with no bungs , greatly build intake & loved how it is made Tried to install the Alky meth nozzle which goes from the inside of the tube & couldn't or maybe I was doing it wrong cause the bungs are threaded from the outside, so i contacted Race Proven Motorsports regarding this & they said it has to go from outside so I sent a pic of how alky nozzle goes from the inside & never heard from them again & now even here I asked with no answer I could of ordered the one no bungs & have it drilled for the meth nozzle no big deal & maybe I didn't know how to install the nozzle, but being a vendor over here you need to stand behind your product . Ahmad
__________________
2017 ZL1 A10 SW (SOLD)
Whipple 2.9 with 3.2 Pulley, Weapon-X Stage 3 Cam, FIICHILLER ,LG Motorsports LT, Borla S type, ROTFAB Big Gulp, Big 3 Reservoir Glassskinz rear window valance . 2012 ZL1 A6 (SOLD) Forged 376 CI, LSA HeartBeat, Mast Medium Bore Heads & JDP ZLR Cam, ARH LT , MagnaFlow Resonated X + Borla Atak Catback, ADM 102mm Snout, CAI, NW102MM TB, ID850, Fore Triple Fuel Pump, MSD Wire's, Moroso CC. Alky Control, FIICHILLER. |
10-25-2017, 09:53 AM | #25 | ||
Drives: 96SS Join Date: May 2009
Location: New Castle Delaware
Posts: 1,948
|
Quote:
AIT is necessary when running meth so the AIT sensor can get moved so it will read the change in air temp. We cant sell them with no logo, We could sell a non coated one but it would have to be the next time we make a batch. Which may be a while bc we just got a bunch made Quote:
If the car is at our shop we can deff do that yes. Cant do it with out a car though. |
||
10-25-2017, 10:01 AM | #26 | |
Drives: 09 G8 GT Join Date: Jun 2011
Location: New Castle, Delaware
Posts: 127
|
Quote:
I apologize for the miscommunication. I replied to every one of your emails I received. Please PM me if you are still having issues and we'll be happy to get you fixed up. |
|
10-25-2017, 03:58 PM | #27 | |
Drives: 2017 ZL1 A10 Join Date: Aug 2009
Location: Dubai
Posts: 1,250
|
Quote:
Ahmad
__________________
2017 ZL1 A10 SW (SOLD)
Whipple 2.9 with 3.2 Pulley, Weapon-X Stage 3 Cam, FIICHILLER ,LG Motorsports LT, Borla S type, ROTFAB Big Gulp, Big 3 Reservoir Glassskinz rear window valance . 2012 ZL1 A6 (SOLD) Forged 376 CI, LSA HeartBeat, Mast Medium Bore Heads & JDP ZLR Cam, ARH LT , MagnaFlow Resonated X + Borla Atak Catback, ADM 102mm Snout, CAI, NW102MM TB, ID850, Fore Triple Fuel Pump, MSD Wire's, Moroso CC. Alky Control, FIICHILLER. |
|
10-25-2017, 04:19 PM | #28 |
Drives: 96SS Join Date: May 2009
Location: New Castle Delaware
Posts: 1,948
|
We never use alky control stuff... ANYTHING that goes in from the inside of the pipe would scare me a little. If that ever came loose it wouldnt be good.
|
|
|
Tags |
5" intake, best intake, camaro intake, zl1 |
|
|