[18LTLoveIt]

Noticed some weather upper door weather stripping shredding over right side of driver window. The car has 182 miles.

[srcstc]

Originally Posted by hotlap

I like that a lot!

Me too! Link?

[the_swiSS]

I parked in full sunlight for the first time in an empty parking lot. Might have to get the paint corrected, it's quite rough in a few spots...

[DM1LE]

Installed the GM Dark Tail lights and Zl1 1LE third brake light. Before and after pics attached.

[Bad Anvil Garage]

Originally Posted by DM1LE

Installed the GM Dark Tail lights and Zl1 1LE third brake light. Before and after pics attached.

That looks WAY better!

[craigss50]

Originally Posted by 1hprush

I took a closer look last night at the SS front grill badge. I still didn't see any retainer clips. Do I need to remove the SS badge first to access the backing plate to find the retaining clips..

I can look from behind through the hood latch opening and see the chrome plastic retainer clips. I used a long flat blade screwdriver to push from behind. I was not successful but if I was more aggressive it would come off. I was afraid of breaking something. Besides like you the mounting plate looks like part of the grill.

[MANNAXMAN]

Originally Posted by chevyboy01438

Made a hood prop for shows! Doors are next.

Originally Posted by 1hprush

How did you remove the SS badge and backing plate that it's mounted on, from the front grill? From what I can tell, after removing the SS badge the backing plate is molded onto the grill itself. Thx.

I know you already got your answer in your other thread, that the backing plate is molded into the grill. But, if you look closely, the OP did not remove the backing plate. It's just hard to see in that picture.

[chiefmg]

Received the SEMA grille I ordered from Wildhammer last week. Waiting to install it until I receive the ZL1 Addons radiator screen ordered at the same time, no sense pulling the bumper cover twice.

[ssmike]

Hired a spy to watch over Blizzard in the parking lot!

[1hprush]

Originally Posted by hworth18

It's not, move a couple of retaining clips and it just pops off.

Originally Posted by starscream5000

There's a plastic plate on the backside of the badge that holds it to the front grill, once you pry that plate off, the badge slides straight forward and off the grill, for a nice clean look. once you clean off the dust from where the badge sat, you'll never even know there was something there to begin with!

Originally Posted by craigss50

I can look from behind through the hood latch opening and see the chrome plastic retainer clips. I used a long flat blade screwdriver to push from behind. I was not successful but if I was more aggressive it would come off. I was afraid of breaking something. Besides like you the mounting plate looks like part of the grill.

Originally Posted by MANNAXMAN

I know you already got your answer in your other thread, that the backing plate is molded into the grill. But, if you look closely, the OP did not remove the backing plate. It's just hard to see in that picture.

Thanks for all the responses, looks like I'll be re-applying my SS badge!

[peteric]

I just cleaned the interior. Washed and waxed the body.

[18LTLoveIt]

Camaro's 1st bath, 201 miles on odo.

[Cgocifer]

Originally Posted by DM1LE

Installed the GM Dark Tail lights and Zl1 1LE third brake light. Before and after pics attached.

I cant figure these lights out. Are they clear, smoked, slightly smoked?

They look different in pics depending on the light.

Regardless, they are awesome and I need to order some pronto! All SS at least should come with them.

[Cgocifer]

Originally Posted by ssmike

Hired a spy to watch over Blizzard in the parking lot!

As long as he doesnt poop on it!