10-29-2020, 05:09 PM | #1 |
Drives: 2020 Camaro ZL1 Join Date: Oct 2020
Location: Fort Worth, Texas
Posts: 1,150
|
dumb question about windows
I am getting my ZL1 tinted tomorrow and the windows unroll about a half an inch each time I open my car, I know they don't want you to unroll them for a couple days AFTER their tinted, is there any way to turn this "feature" off?
__________________
2020 ZL1 A10 Shadow Gray Metallic
Magnuson Magnum DI TVS2650R| Mamo Throttle Body V2| RotoFab Intake| AWE Touring Catback Exhaust| TCM Tune| Tune| Eibach Pro| BMR Rear Cradle Lockout| PPF| Ceramic| BCForged HCS21 |
10-29-2020, 05:24 PM | #2 |
Drives: 2019 ZL-1, Shadow Gray, Sold Join Date: Jan 2019
Location: Fredericksburg, VA
Posts: 1,390
|
No, dont believe so.
|
10-29-2020, 05:28 PM | #3 |
Drives: 19 Chevrolet Camaro 2SS 1LE Shock Join Date: Apr 2020
Location: BC, Canada
Posts: 1,947
|
It does that so the window won't smash into the seal or worse, the body of the car.
You can disconnect the battery so the windows won't automatically roll, but be very, very careful if you need to open or close the door.
__________________
Current:
2019 Chevrolet Camaro 2SS 1LE M6 Shock GM Performance Intake and that's it, because driver mods before car mods Past: 2009 Mazda RX-8 GT M6 Velocity Red Mica (Sold) 2015 Chevrolet Corvette Z51 2LT M7 Velocity Yellow Tintcoat (Flood totaled) |
10-29-2020, 05:30 PM | #4 |
Drives: 2016 1ss camaro Join Date: Feb 2016
Location: 909
Posts: 9,817
|
no problems with mine
__________________
16 1SS NIGHTFALL GRAY METALLIC WITH NPP #BECAUSERACECAR #SAVETHEMANUALS
|
10-29-2020, 05:57 PM | #5 |
Drives: 2019 Chevy Camaro ZL1 M6 Join Date: Jul 2019
Location: Sea level
Posts: 1,252
|
If you are using a competent shop they won’t have any problems handling that. They can make it stick better in that area. I had no issues with it when mine were tinted.
|
10-29-2020, 06:42 PM | #6 |
Drives: 2017 Camaro ZL1 Coupe Join Date: May 2016
Location: Georgia
Posts: 5,813
|
Didn’t have a problem with either my 2016 SS or my 2017 ZL1. The same person did my 2016 when it was new and after I traded for my ZL1 I went back to him to do the ZL1 windows. You can’t let them all the way down for a couple of days or so to give the tint time to fully dry.
__________________
ZL1 Coupe, PDR, Exposed carbon fiber hood insert, My Link with Nav, M6 6 speed and Silver Ice Metallic. Mods done: ceramic window tint, GM Accessories Camaro floor mats and Roto-Fab CAI.
|
10-29-2020, 06:45 PM | #7 |
Drives: 2017 Camaro ZL1 Coupe Join Date: May 2016
Location: Georgia
Posts: 5,813
|
And if the tint shop uses ceramic tint then I would advise you to get that tint. It reflects the sun better than regular tint!
__________________
ZL1 Coupe, PDR, Exposed carbon fiber hood insert, My Link with Nav, M6 6 speed and Silver Ice Metallic. Mods done: ceramic window tint, GM Accessories Camaro floor mats and Roto-Fab CAI.
|
10-29-2020, 11:49 PM | #8 |
Drives: Chevrolet Camaro ZL1 1LE Join Date: Jun 2019
Location: Florida
Posts: 127
|
Ceramic IR tint! Stay cool.
|
10-30-2020, 12:28 AM | #9 |
Drives: 2020 Camaro ZL1 Join Date: Oct 2020
Location: Fort Worth, Texas
Posts: 1,150
|
Thanks for the responses everyone....I am taking it to a competent tint shop whom I’m sure has dealt with this issue before....I just wanted to know if there was any way to alleviate that problem so they wouldn’t have to worry about it.....and on a side note I am getting the Ceramic tint
__________________
2020 ZL1 A10 Shadow Gray Metallic
Magnuson Magnum DI TVS2650R| Mamo Throttle Body V2| RotoFab Intake| AWE Touring Catback Exhaust| TCM Tune| Tune| Eibach Pro| BMR Rear Cradle Lockout| PPF| Ceramic| BCForged HCS21 |
10-30-2020, 02:53 AM | #10 |
Drives: 2013 Triple Black ZL1 Vert M6 ECF Join Date: Mar 2011
Location: Trenton, Michigan
Posts: 7,047
|
The window drops down a bit so it clears the upper seal area before the door opens. When the door is closed, the windows will go up all the way into the seal area to provide a more positive seal when the door is closed.
because of this function, you cannot disable that feature. |
10-30-2020, 07:33 AM | #11 |
Petro-sexual
|
I didn't have a problem. Maybe you can leave them just-cracked a bit to "disable" that feature. I don't recall if I did, but if you're that concerned maybe that's an option.
__________________
'20 ZL1 Black "Fury" A10, PDR, Exposed CF Extractor Magnuson Magnum DI TVS2650R // RFBG // Soler 103 // TooHighPSI Port Injection // THPSI Billet Lid // FF // Katech Drop-In // PLM Heat Exchanger // ZLE Cradle bushings // BMR Chassis-Suspension Stuff // aFe Bars // Diode Dynamics LEDs // ACS Composites Guards // CF Dash // Aeroforce // tint // other stuffs |
10-30-2020, 07:58 AM | #12 | |
Drives: E92 BMW M3 Join Date: Oct 2012
Location: Houston
Posts: 4,496
|
Quote:
__________________
SOLD - 2013 1LE - Pat G Spec'd Cam, NPP with 1 7/8" Long Tube Headers with High Flow Cats, Intake w/scoop, Ported Throttle Body, and Apex 1.25" Lowering Springs.
J-Rod Built and Matt@FSP Tuned |
|
|
|
Post Reply
|
|
|