Finally installed my ROTO-FAB CAI. - Page 2 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

rtg · 07-21-2013, 04:38 PM

Thanks for pointing this out.

It looks close in the picture but around 3/4" to 1" away. Should be OK unless it moves around.

Rob

OldJedi · 07-21-2013, 08:49 PM

I did mine as well, finally! How and where did you guys route the ground cable around the box to the stud? Mine seems to be very tight going around the air box and the fender. I can see where in time the edge of the box would cut the insulation on the cable. Any suggestions from RotoFab installers would be appreciated.

djnice · 07-21-2013, 09:44 PM

Quote:

Originally Posted by rtg

Thanks for pointing this out.

It looks close in the picture but around 3/4" to 1" away. Should be OK unless it moves around.

Rob

Rotate the threaded 90 deg elbow more...unscrew it a little.

AcmeRkt1 · 07-21-2013, 10:04 PM

I just put mine on the other day as well, awesome product.

Jason

rtg · 07-21-2013, 10:27 PM

See if you can pull a little more slack thru the black tie down near the battery +(red) port. I got about another inch.

Rob

Quote:

Originally Posted by OldJedi

I did mine as well, finally! How and where did you guys route the ground cable around the box to the stud? Mine seems to be very tight going around the air box and the fender. I can see where in time the edge of the box would cut the insulation on the cable. Any suggestions from RotoFab installers would be appreciated.

djnice · 07-22-2013, 04:28 PM

Quote:

Originally Posted by OldJedi

I did mine as well, finally! How and where did you guys route the ground cable around the box to the stud? Mine seems to be very tight going around the air box and the fender. I can see where in time the edge of the box would cut the insulation on the cable. Any suggestions from RotoFab installers would be appreciated.

Take a look at the instructions for the Lingenfelter system. They run it under the seal where there is already a dip in the body that creates a lower pressure spot in the seal. That's where I ran mine. Lingenfelter's box is made by RotoFab.

They also remove the ground stud and change it for a bolt. They get rid of the clean air canister too.

http://www.lingenfelter.com/sites/lp...t%20v1.1_1.pdf

OldJedi · 07-22-2013, 08:30 PM

Quote:

Originally Posted by djnice

Take a look at the instructions for the Lingenfelter system. They run it under the seal where there is already a dip in the body that creates a lower pressure spot in the seal. That's where I ran mine. Lingenfelter's box is made by RotoFab.

They also remove the ground stud and change it for a bolt. They get rid of the clean air canister too.

http://www.lingenfelter.com/sites/lp...t%20v1.1_1.pdf

Thanks guys I appreciate the help.

JB12ZL1 · 08-18-2013, 02:43 PM

looks great! I just installed mine and love it!

07-21-2013, 04:38 PM	#15
rtg Drives: 2013 ZL1 Join Date: Jun 2013 Location: CT Posts: 65	Thanks for pointing this out. It looks close in the picture but around 3/4" to 1" away. Should be OK unless it moves around. Rob __________________ 2013 ZL1 VR

07-21-2013, 08:49 PM	#16
OldJedi Use the Force Drives: 2015 Corvette Z51, 2018 Porsche GTS Join Date: Jan 2010 Location: Davie, Fl. Posts: 3,862	I did mine as well, finally! How and where did you guys route the ground cable around the box to the stud? Mine seems to be very tight going around the air box and the fender. I can see where in time the edge of the box would cut the insulation on the cable. Any suggestions from RotoFab installers would be appreciated. Attached Images __________________ Walk softly, carry a light saber and drive a ZL1!

07-21-2013, 10:04 PM	#18
AcmeRkt1 Drives: 2013 ZL1, 45th Anniversary 2SS Join Date: Apr 2012 Location: Castle Rock Colorado Posts: 27	I just put mine on the other day as well, awesome product. Jason __________________ 2013 ZL1 #7593 Black, CCW CV590 wheels anodized red, exposed carbon fiber hood, carbon fiber rear spoiler, JDP Motorsports ZL-850 package. JDP Motorsports Anti-wheel hop package. 2012 2SS 45th Anniversary. Rotofab CAI, SLP chin spoiler, SLP heritage shifter, Eibach lowering springs, Red bowties. SOLD 2002 Corvette Coupe - Black - tinted, 1SA, MN6. A&A P1SC Procharger kit, Comp Cams 220/224 .581/.581 114lsa, RPS Stage 4 clutch, C6ZO6 shocks and sway bars, Borla cat-back, chrome Z06's (18/9.5f & 18/12r) and some other stuff. 571rwhp 530 rwtq. SOLD

08-18-2013, 02:43 PM	#22
JB12ZL1 Drives: victory red Camaro ZL1 Join Date: May 2013 Location: Lynnfield Ma Posts: 492 View My Garage	looks great! I just installed mine and love it!