Speed engineering full exhaust kit?? - Page 3 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

awsm66 · 05-09-2019, 04:59 PM

Anyone try this out (with the mufflers) to see how the drone is?

I have got to get rid of this Magnaflow 3" exhaust and its drone.

2010reddevil · 05-09-2019, 06:52 PM

Man I don't see where you have drone from? I have the same system and no cats with headers and it only drones right at 55mph or about 1500-1600 rpm. Other than that, has a great tone/sound.

awsm66 · 05-09-2019, 07:03 PM

Quote:

Originally Posted by 2010reddevil

Man I don't see where you have drone from? I have the same system and no cats with headers and it only drones right at 55mph or about 1500-1600 rpm. Other than that, has a great tone/sound.

Not sure we have the same system if going by your description (though may be the same but with just dual outlets).

I have the ZL1 3" system. It says its a street system (part#15053) but with headers and no cats its pretty loud but the drone is horrible. My wife hates riding in the car with me.

Not as loud as the stainless works chambered system I had (and hated because I despise the raspyness of glasspacks...to each his own, i know several like it) but still pretty loud.

I am also not a fan of loud exhaust anymore anyway.

2010reddevil · 05-10-2019, 02:52 AM

Mine is the 3" system as well, but with single tips. Mine really only drones at 1500-1600 rpm. Above or below it just has a healthy and deep sound. Not too loud or quiet. Whack the go fast pedal and it definitely has some bark. Cold starts are my fav hehe.

Sinister10 · 05-10-2019, 05:19 PM

ive got a set of TSP 1 7/8 L.Ts and im looking for an aftermarket exhaust from the headers back to my SLP LM2 axel back. i was hoping this kit will work, but really dont want to buy the mufflers w/tips. where are you guys getting the x pipes at?

also, since my motor is pretty much stock, woulnt a 3in exhaust hurt my torque number? i focus more on building torque numbers rather than horespower. Monstrous torque is more fun in my opinion.

do they sell a resonator delete kit for the factory exhaust?

STALKER · 05-11-2019, 05:23 AM

Quote:

Originally Posted by Sinister10

ive got a set of TSP 1 7/8 L.Ts and im looking for an aftermarket exhaust from the headers back to my SLP LM2 axel back. i was hoping this kit will work, but really dont want to buy the mufflers w/tips. where are you guys getting the x pipes at?

It most likely won't fit. Most of these manufacturers design cat back system to bolt up to their header systems only, so mixing and matching components doesn't work 9.5 times out of 10.

Quote:

Originally Posted by Sinister10

also, since my motor is pretty much stock, woulnt a 3in exhaust hurt my torque number? i focus more on building torque numbers rather than horespower. Monstrous torque is more fun in my opinion.

2.5" is more than sufficient up 600+ rwhp, so you wouldn't benefit from going to a 3" cat back, but it most likely wouldn't hurt you that much either. The difference would barely be measurable.

Quote:

Originally Posted by Sinister10

do they sell a resonator delete kit for the factory exhaust?

Not that I'm aware of.

PhantomBlack · 11-10-2019, 09:29 PM

So any updates on this exhaust? Sound clips anyone?
500 bucks for a full catback got me thinking about getting one.

Crankshaft · 11-11-2019, 12:05 AM

Quote:

Originally Posted by PhantomBlack

So any updates on this exhaust? Sound clips anyone?
500 bucks for a full catback got me thinking about getting one.

I have their complete kit on my car, i actually got everything done under $850 including the tune since i had gotten the exhaust for 3 something and 1 7/8 headers for $249. Its a deep tone like a glasspack with some drone on highway at certain RPM but quiet cruising 60-67MPH, best part about it though is that you can switch out into 40 or 44 series from flowmaster with 4 clamps and have different exhaust sounds as you fancy. If you have a lift or access to one it will allow you to move everything around to make it fit more the way you want to but the exhaust does hang a bit low for those lowered it might be lower than they would like. Right now i am using the kit with a 2 chamber muffler like the original 40 and like the way the car sounds.

SE full kit
https://youtu.be/sab83n22NhY

SE kit with 2 chamber mufflers
https://youtu.be/lFJbGZFCAbI

PhantomBlack · 11-13-2019, 08:37 PM

Quote:

Originally Posted by Crankshaft

I have their complete kit on my car, i actually got everything done under $850 including the tune since i had gotten the exhaust for 3 something and 1 7/8 headers for $249. Its a deep tone like a glasspack with some drone on highway at certain RPM but quiet cruising 60-67MPH, best part about it though is that you can switch out into 40 or 44 series from flowmaster with 4 clamps and have different exhaust sounds as you fancy. If you have a lift or access to one it will allow you to move everything around to make it fit more the way you want to but the exhaust does hang a bit low for those lowered it might be lower than they would like. Right now i am using the kit with a 2 chamber muffler like the original 40 and like the way the car sounds.

SE full kit
https://youtu.be/sab83n22NhY

SE kit with 2 chamber mufflers
https://youtu.be/lFJbGZFCAbI

Thanks for the review and video clips. I think I may have found my new setup!

RyangAsh · 01-22-2020, 10:08 AM

I have SE longtubes and SE full exhaust kit on my car(no cats). Sounds great IMO

smegal417 · 01-22-2020, 11:48 PM

Was going to, but I doubt it sounds any better so I'll leave mine as is https://youtu.be/R_2QF4ZuNAM

Sent from my SM-G975U1 using Tapatalk

SFR7771 · 03-15-2022, 03:40 PM

Do you have a pic of super 10 mounted? Sounds sick how it sound in the car?

Quote:

Originally Posted by smegal417

Was going to, but I doubt it sounds any better so I'll leave mine as is https://youtu.be/R_2QF4ZuNAM

Sent from my SM-G975U1 using Tapatalk

05-09-2019, 06:52 PM	#30
2010reddevil Drives: 2010 Camaro 2SS Victory Red 6M Join Date: Apr 2015 Location: Gulf Coast, TX Posts: 1,424	Man I don't see where you have drone from? I have the same system and no cats with headers and it only drones right at 55mph or about 1500-1600 rpm. Other than that, has a great tone/sound. __________________ 2011 2SS 6A Red Jewel Metallic, Vararam Tune CAI, Magnaflow 3" Competition c/b, Speed Engineering 1-7/8 LT's, Circle D 5C, M/T 275/40R20 S/S, HPTuners tune by Ryan@GPI 12.3 @ 112 ACM as of 12/22/19 Gone on 12/28/19 R I P 2010 2SS 6M Victory Red/Black (old ride) CAI intake, Speed Engineering 1 7/8" LT's, X4 base tune, Flowmaster Outlaw axle-back. 12.6 @ 115 SAR as of 9/19/15 Gone but never forgotten.

05-10-2019, 02:52 AM	#32
2010reddevil Drives: 2010 Camaro 2SS Victory Red 6M Join Date: Apr 2015 Location: Gulf Coast, TX Posts: 1,424	Mine is the 3" system as well, but with single tips. Mine really only drones at 1500-1600 rpm. Above or below it just has a healthy and deep sound. Not too loud or quiet. Whack the go fast pedal and it definitely has some bark. Cold starts are my fav hehe. __________________ 2011 2SS 6A Red Jewel Metallic, Vararam Tune CAI, Magnaflow 3" Competition c/b, Speed Engineering 1-7/8 LT's, Circle D 5C, M/T 275/40R20 S/S, HPTuners tune by Ryan@GPI 12.3 @ 112 ACM as of 12/22/19 Gone on 12/28/19 R I P 2010 2SS 6M Victory Red/Black (old ride) CAI intake, Speed Engineering 1 7/8" LT's, X4 base tune, Flowmaster Outlaw axle-back. 12.6 @ 115 SAR as of 9/19/15 Gone but never forgotten.

05-10-2019, 05:19 PM	#33
Sinister10 Drives: 2010 Camaro SS Join Date: Jul 2018 Location: Indiana Posts: 543	ive got a set of TSP 1 7/8 L.Ts and im looking for an aftermarket exhaust from the headers back to my SLP LM2 axel back. i was hoping this kit will work, but really dont want to buy the mufflers w/tips. where are you guys getting the x pipes at? also, since my motor is pretty much stock, woulnt a 3in exhaust hurt my torque number? i focus more on building torque numbers rather than horespower. Monstrous torque is more fun in my opinion. do they sell a resonator delete kit for the factory exhaust? __________________ 2010 2SS/RS 6M, MGW flatstick, CAI cold air intake, SLP loudmouth 2 axleback, TSP 1 7/8 headers w/ hfc, pfadt 1" springs, SRP pedals, emblempros "6.2L" emblems on hood, ZL1 grill, M/T SC-5 wheels, nitto motivo 275f 315r. ZL1 addons wickerbill, smoked lenses, resonator delete x pipe, diode dynamics DRLs 1LE suede steering wheel, mighty mouse CC. SCTX4 and Dyno Steve tune.

05-09-2019, 04:59 PM	#29
awsm66 Drives: Victory Red 2011 2SS Join Date: Dec 2016 Location: Meridian, MS Posts: 79	Anyone try this out (with the mufflers) to see how the drone is? I have got to get rid of this Magnaflow 3" exhaust and its drone.

11-10-2019, 09:29 PM	#35
PhantomBlack Drives: 2014 Camaro 2SS Join Date: Oct 2017 Location: Brooksville, FL Posts: 181	So any updates on this exhaust? Sound clips anyone? 500 bucks for a full catback got me thinking about getting one.

01-22-2020, 10:08 AM	#38
RyangAsh Drives: 2014 ZL1 Join Date: Apr 2018 Location: KCMO Posts: 180	I have SE longtubes and SE full exhaust kit on my car(no cats). Sounds great IMO

01-22-2020, 11:48 PM	#39
smegal417 Drives: 2010 Camaro 2SS/RS Join Date: Jan 2019 Location: Springfield, MO Posts: 71	Was going to, but I doubt it sounds any better so I'll leave mine as is https://youtu.be/R_2QF4ZuNAM Sent from my SM-G975U1 using Tapatalk