Aluminum LT4 Thermostat housing - Page 3

CalgaryZL1 · 01-27-2024, 08:31 PM

Quote:

Originally Posted by pitrott1

Ditto here, use that as a spare also. It's all about the housing!

+1 on the housing

pitrott1 · 01-28-2024, 12:23 PM

All,
Looking for the LT thermostat by itself? both 160% and 180% can be had here.

Bangkok_ZL1 · 02-05-2024, 12:10 PM

Quote:

Originally Posted by Tay

I think I found one: https://radrides.com/product/lt1-lt4...ostat-housing/

Thank you so much! It does say it uses the stock Thermostat. Mine is actually a lower temp thermostat. but it's made for the stock housing. I'm getting this. after I inquire about the overflow nipple...

Bangkok_ZL1 · 02-05-2024, 12:11 PM

Quote:

Originally Posted by CalgaryZL1

Yes, I understand the different degree options. I would just like a factory one on hand, if I recall I think they have 187°. I have read they are possibly more reliable. And a spare on hand never hurts no matter what the degree setpoint is, I don’t track my car I just didn’t want a plastic housing.

ABSOLUTELY

Tay · 02-05-2024, 06:25 PM

Quote:

Originally Posted by Bangkok_ZL1

Thank you so much! It does say it uses the stock Thermostat. Mine is actually a lower temp thermostat. but it's made for the stock housing. I'm getting this. after I inquire about the overflow nipple...

Let us know what they say about the... umm.. teat...

*radz28* · 02-06-2024, 10:40 AM

TOOHIGHPSI lists one too. I just noticed it last week

https://toohighpsi.com/products/tooh...mostat-housing

Tay · 02-06-2024, 04:09 PM

Quote:

Originally Posted by radz28

TOOHIGHPSI lists one too. I just noticed it last week

https://toohighpsi.com/products/tooh...mostat-housing

That one still uses an LS thermostat unfortunately. OP is looking for one that uses the LT thermostat.

Bangkok_ZL1 · 02-28-2024, 11:21 AM

I guess this thermostat doesn't exist. This will be a priority project, to buy the Aluminum housing and an LS Thermostat because I installed Forced Induction's head/blower spacer plates and the belt just barely made it on with a little persuasion (a dab of WD-40 on the belt to help slide it over the tensioner while my girl was limiting the tensioner with a breaker bar). There is about 1mm of space between the tensioner's end point and its current position. I might get a bit more space after running the engine, but I'm not waiting around for failure on this one. Thank you everybody for trying to find an Aluminum housing. And for the housing without a nipple, the company never replied...

01-28-2024, 12:23 PM	#30
pitrott1 OSCM(SW) USN Ret. Drives: 2023 Camaro 2SS-1LE VOM 6M Join Date: Apr 2023 Location: MD Posts: 195	All, Looking for the LT thermostat by itself? both 160% and 180% can be had here. Attached Images __________________ 2023 2SS-1LE VOM, 6M, SR S-TBrace, A-PDL's, Fuzzy suede KP's, NAV 1100 3/29/23 2000 3/30/23 3300 5/1/23 3800 5/4/23 4200 6/1/23 6000 6/6/23

02-06-2024, 10:40 AM	#34
radz28 Petro-sexual Drives: Ultra-Grin Join Date: Oct 2006 Location: Crazy Coast Posts: 15,201 View My Garage	TOOHIGHPSI lists one too. I just noticed it last week https://toohighpsi.com/products/tooh...mostat-housing __________________ '20 ZL1 Black "Fury" A10, PDR, Exposed CF Extractor Magnuson Magnum DI TVS2650R // RFBG // Soler 103 // TooHighPSI Port Injection // THPSI Billet Lid // FF // Katech Drop-In // PLM Heat Exchanger // ZLE Cradle bushings // BMR Chassis-Suspension Stuff // aFe Bars // Diode Dynamics LEDs // ACS Composites Guards // CF Dash // Aeroforce // tint // other stuffs

02-28-2024, 11:21 AM	#36
Bangkok_ZL1 ZL1 Believer Drives: 2019 Camaro ZL1 Join Date: Oct 2020 Location: Bangkok, Thailand Posts: 532	I guess this thermostat doesn't exist. This will be a priority project, to buy the Aluminum housing and an LS Thermostat because I installed Forced Induction's head/blower spacer plates and the belt just barely made it on with a little persuasion (a dab of WD-40 on the belt to help slide it over the tensioner while my girl was limiting the tensioner with a breaker bar). There is about 1mm of space between the tensioner's end point and its current position. I might get a bit more space after running the engine, but I'm not waiting around for failure on this one. Thank you everybody for trying to find an Aluminum housing. And for the housing without a nipple, the company never replied...

User Name		Remember Me?
Password