[DorkMissile]

Originally Posted by Markoz28

Any pics of this?

Now that I could pull the cover off and take a look, I can see what I did exactly

I drilled the hole right under the base of the lower gage, then ran one zip tie thru it and I zipped it back on itself. I then left the long tail on it, ran it thru the hole in the bracket on the metal on the left side of the dash and thru a washer on the far side. I then used the head off of another tie to put tension on everything. It is not strung tight, but not loose.

[Psychosocial]

Originally Posted by DorkMissile

I have a dual gauge pod that goes in the defrost vent. AEM wideband in the lower hole, iDash in the upper.

I never had much luck gettin the pod to stay put using the snap in tabs - so what I did is drilled a small hole in one of the ribs on the underside of the pod, then looped a wider zip-tie thru the hole. I then strapped the zip tie around one of the metal braces in the dash that you can see on the left side of the dash once you remove the side cover.

Thing is locked in solid now.

This is very helpful. Thanks for sharing your creativity!

[Markoz28]

Originally Posted by DorkMissile

Now that I could pull the cover off and take a look, I can see what I did exactly

I drilled the hole right under the base of the lower gage, then ran one zip tie thru it and I zipped it back on itself. I then left the long tail on it, ran it thru the hole in the bracket on the metal on the left side of the dash and thru a washer on the far side. I then used the head off of another tie to put tension on everything. It is not strung tight, but not loose.

Awesome! I may try this

[DorkMissile]

On a side note - I have actually purchased a 3D printer and plan on coming up with a few things that I think will be a better idea than what can be bought at this time to mount gauges, so stay tuned for what's next

[jshropshire17@gmail.com]

Originally Posted by JANNETTYRACING

Thanks yes we carry single and dual pods as well as the Pillar pods.

https://jannettyracing.com/products/...16-2018-camaro

https://jannettyracing.com/products/...-camaro-ss-zl1

https://jannettyracing.com/products/...od-2016-camaro

If you wanted to use the pillar dual gauge pod along with a single gauge pod next to it on the dash, would the single and dual pods fit next to each other?

[jshropshire17@gmail.com]

Originally Posted by JANNETTYRACING

Thanks yes we carry single and dual pods as well as the Pillar pods.

https://jannettyracing.com/products/...16-2018-camaro

https://jannettyracing.com/products/...-camaro-ss-zl1

https://jannettyracing.com/products/...od-2016-camaro

Can the dual pillar and single dash pods be used together?

[JANNETTYRACING]

Originally Posted by jshropshire17@gmail.com

Can the dual pillar and single dash pods be used together?

No sir I do not believe so.

[parbreak]

Originally Posted by jshropshire17@gmail.com

Can the dual pillar and single dash pods be used together?

They definitely can NOT. I have the dual pillar pod from ZZP and it extends down very close to the dash top. A single defrost vent pod would not fit.

[CamaroATL]

Originally Posted by parbreak

They definitely can NOT. I have the dual pillar pod from ZZP and it extends down very close to the dash top. A single defrost vent pod would not fit.

how did ya'll get your ZZP pillar to lock back in place? I'm assuming the clip on mine is messed up because it will not click into place up top. Anybody know a part number for that clip?

[ParisTNDude]

Where does the gauge get it's input? Is it electric or does it sense PSI from the super charger? I'm definitely a newbe at this discussion.