You are browsing camaro6 
05-15-2022, 07:03 PM
|
#1 |
 Drives: 2022 Zl1 Join Date: Dec 2021
Location: CT
Posts: 51
|
Borla S type Axle Back Rattle
Hi,
I just installed a Borla S type Axle Back on my ZL1 and am getting a rattling sound from the drivers side valve when open and closed. Has anybody experienced this? |
|
|
|
05-15-2022, 07:34 PM
|
#2 | |
     
Drives: 2019 ZL1 Join Date: Mar 2019
Location: NJ
Posts: 1,534
|
Quote:
Check to make sure the valve isn't loose. If the valve isnt lose and working fine make sure the muffler isn't hitting the heat shield above it.
__________________
928rwhp - 93 | 1040rwhp/898rwrq - E65 SAE
LME 377 LT4 Short Block | Magnuson 2650 80mm upper w/13% lower (9.06) | DSX Lid & Valve Covers | CSP Custom Cam w/32% fuel lobe | CID Heads | NW 103mm TB | Roto Fab Big Gulp | CSP 2" Headers w/Green GESI Gen 2 Cats | Borla 3" Full Cat Back w/ S-Type| Mighty Mouse Wild Catch Can| Custom Holley Low side Fuel system| TooHigh PSI Port Injection w/Holley Controller | Forced Inductions Interchiller w/2 gallon fender tank | TK Performance built 10L90 |
|
|
|
|
|
05-15-2022, 08:50 PM
|
#3 |
|
Drives: 2022 Zl1 Join Date: Dec 2021
Location: CT
Posts: 51
|
The valve is tight. I checked and don't see any clearance issues. I am gonna contact Borla tomorrow. This should not be happening with expensive mufflers like this
|
|
|
|
|
05-15-2022, 08:52 PM
|
#4 | |
|
Drives: 2019 ZL1 Join Date: Mar 2019
Location: NJ
Posts: 1,534
|
Quote:
You sure its the valve and its not hitting anything?
__________________
928rwhp - 93 | 1040rwhp/898rwrq - E65 SAE
LME 377 LT4 Short Block | Magnuson 2650 80mm upper w/13% lower (9.06) | DSX Lid & Valve Covers | CSP Custom Cam w/32% fuel lobe | CID Heads | NW 103mm TB | Roto Fab Big Gulp | CSP 2" Headers w/Green GESI Gen 2 Cats | Borla 3" Full Cat Back w/ S-Type| Mighty Mouse Wild Catch Can| Custom Holley Low side Fuel system| TooHigh PSI Port Injection w/Holley Controller | Forced Inductions Interchiller w/2 gallon fender tank | TK Performance built 10L90 |
|
|
|
|
|
05-17-2022, 03:10 PM
|
#5 |
|
Drives: 2022 Zl1 Join Date: Dec 2021
Location: CT
Posts: 51
|
Spoke to Borla they are sending me a new valve. Hopefully this fixes the issue.
|
|
|
|
|
05-17-2022, 06:32 PM
|
#6 | |
 Drives: R.I.P. 2021 ZL1 & 2019 Rd Garn 2SS Join Date: Dec 2019
Location: Chattanooga, TN
Posts: 268
|
Quote:
|
|
|
|
|
|
|
|
|
|
Post Reply
|
|
|
