05-03-2024, 12:48 PM | #1 |
Drives: 2019 Camaro 1SS1LE Join Date: Jan 2024
Location: Utah
Posts: 178
|
GM Engineering
If you’ve never had a psychotic break or wanted to prevent stupidity by way of genocide, try removing a GM manual transmission shifter pins. The most retarded feat of engineering ever conceived. What the **** was wrong with good old bolts and threads? No let’s use a spring loaded retaining pin that can never be uninstalled without some form of telekinesis. One day when I am over this car, I will cheer its sale and happily go back to a Mustang. GM’s manual driveline is terrible to work on.
Thanks for letting me rant. What a pile.
__________________
2019 1SS1LE M6 Shadow Grey Metallic
ProCharger D1X Race Kit - 4.25" Pulley || GPI Pistons/Rods - ACL Bearings - ARP Hardware || LME Timing Chain Guide || Katech C5R Timing Chain || Katech OE Spec Billet Oil Pump || OE Ported Heads || CHE Trunnion Upgrade || BTR 220 Cam - BTR .660" Dual Springs - GM Racing "Caddy" Lifters - BTR Chromoly Pushrods (7.825") || ATI Balancer || LT4 Injectors || LT4 HPFP || JMS BAP || DSX Flex Fuel || LT2 Intake Manifold || LTH (Catless) || Stainless Works Redline Series NPP || 91 + Boostane 7/26/2024 Tuning in progress |
05-03-2024, 04:33 PM | #2 |
Drives: Chevrolet Camaro Join Date: Feb 2020
Location: AL
Posts: 52
|
Those things are definitely not made with the intention of service. Most likely a cost saving/assembly choice for the factory.
That said, I'd rather deal with those pins than have anything to do with an MT82 trans in a mustang gt again. |
05-04-2024, 01:17 AM | #3 | |
Drives: 2019 Camaro 1SS1LE Join Date: Jan 2024
Location: Utah
Posts: 178
|
Quote:
__________________
2019 1SS1LE M6 Shadow Grey Metallic
ProCharger D1X Race Kit - 4.25" Pulley || GPI Pistons/Rods - ACL Bearings - ARP Hardware || LME Timing Chain Guide || Katech C5R Timing Chain || Katech OE Spec Billet Oil Pump || OE Ported Heads || CHE Trunnion Upgrade || BTR 220 Cam - BTR .660" Dual Springs - GM Racing "Caddy" Lifters - BTR Chromoly Pushrods (7.825") || ATI Balancer || LT4 Injectors || LT4 HPFP || JMS BAP || DSX Flex Fuel || LT2 Intake Manifold || LTH (Catless) || Stainless Works Redline Series NPP || 91 + Boostane 7/26/2024 Tuning in progress |
|
05-04-2024, 08:38 AM | #4 | |
Drives: 6th gen Join Date: Aug 2013
Location: US
Posts: 3,710
|
Quote:
I did have to deal with the pin when installing the hurst. I can see it being frustrating when you need to breeze through those steps with a job as big as the one you got there. Dam
__________________
‘22 2SS 1LE M6 Summit White - RF, Flexfuel, LT2 intake, 95mm tb, ATI udp, VT ramair, full 28” dragpack - 11.68@122
‘16 1SS M6 LT2 intake + boltons on DR 11.0@126+ (Sold) |
|
05-05-2024, 10:14 AM | #5 |
Drives: 6th gen Join Date: Aug 2013
Location: US
Posts: 3,710
|
Did you go at the pins from the inside of the car?
__________________
‘22 2SS 1LE M6 Summit White - RF, Flexfuel, LT2 intake, 95mm tb, ATI udp, VT ramair, full 28” dragpack - 11.68@122
‘16 1SS M6 LT2 intake + boltons on DR 11.0@126+ (Sold) |
05-06-2024, 11:23 AM | #6 |
Drives: 2017 1SS 6spd Join Date: Jan 2011
Location: Utah
Posts: 2,917
|
OP we all got to vent from time to time, even me- LOL.
Hopefully you were doing this work to upgrade to a Hurst short throw shifter. If that's the case, in a couple weeks you'll be back in love with your Camaro and the PIA pins will be a distant memory. |
|
|
Post Reply
|
|
|