[n12k1]

Hi, is there someone who has a wiring diagram of the LED tail lights, which are used on the RS,SS and ZL1 models? On the plug i see 6 pins, I found out that there are two grounds, one positive for the reverse light, one for the brake/turn light and one for the actual tail light, but have no idea where does the 6th go.

[Trochoidal]

Here’s a thread discussing your topic. It may give you the answer you desire.

https://www.camaro6.com/forums/showthread.php?t=549679

[n12k1]

Originally Posted by Trochoidal

Here’s a thread discussing your topic. It may give you the answer you desire.

https://www.camaro6.com/forums/showthread.php?t=549679

The guy is having the same problem as I am, but the thread ends there.

[Oramac2016]

Originally Posted by n12k1

The guy is having the same problem as I am, but the thread ends there.

What problem are you having?

[n12k1]

Originally Posted by Oramac2016

What problem are you having?

Well I wanted to have tail lights with yellow/orange turn signals, so i purchased EU version tail lights. But i didn't know that the EU camaro use the revese light as a turn signal and so the wiring is different for the US and EU models and now I get hyper flashing when i use the turn signals, even though my stock tail lights are LED.


https://drive.google.com/file/d/17C8...4fb83e5f2jsN8i


On the attached picture you can see one of the pins is missing on the new tail lights

[h018871]

These are for a 2019, but they should be the same

[n12k1]

Originally Posted by h018871

These are for a 2019, but they should be the same

Thanks for the response! I figured out that the problem is that on my new tail lights i am missing the "turn lamp feedback signal", which i have no idea how to simulate on the new lights.

[h018871]

Best guess is that you'll get a message that the lamp is out.

[Peter10654]

Originally Posted by n12k1

Thanks for the response! I figured out that the problem is that on my new tail lights i am missing the "turn lamp feedback signal", which i have no idea how to simulate on the new lights.

You have to install a resistor to say the body control module everything is fine. Maybe the guys from gen5diy can help you

Peter

[Peter10654]

Originally Posted by h018871

These are for a 2019, but they should be the same

Hey mate. Do you have maybe also wiring diagram from the reverse lights connector from the 2019 model? I need to build a custom harness and it would help to identify the type of connector.

Thanks

Peter

[n12k1]

Originally Posted by Peter10654

You have to install a resistor to say the body control module everything is fine. Maybe the guys from gen5diy can help you

Peter

Contacted them but they had no clue about it

[h018871]

Originally Posted by Peter10654

Hey mate. Do you have maybe also wiring diagram from the reverse lights connector from the 2019 model? I need to build a custom harness and it would help to identify the type of connector.

Thanks

Peter

They use the same connectors, x410 & x420, pin 4 for the signal. For European models one of them is the rear fog lamp

Hope this helps

[Peter10654]

Originally Posted by h018871

They use the same connectors, x410 & x420, pin 4 for the signal. For European models one of them is the rear fog lamp

Hope this helps

Thanks mate,

yes I found it and could convert everything I need.

Thanks

Peter

[MakCamaro]

Originally Posted by h018871

These are for a 2019, but they should be the same

Very useful, especially for European models that miss the side markers and the DRLs.

Do you or someone else have a similar diagram, but for the headlights? I am trying to figure out which wire in the headlight to tap into in order to fit aftermarket fog DRLs.

Thanks