[TX18ZL1]

LEDS…

First time she was on a left and I saw this handwriting from the factory… ideas?

[LeonardS]

Originally Posted by TX18ZL1

LEDS…

First time she was on a left and I saw this handwriting from the factory… ideas?

Attachment 1144957

Rear end setup measurements from the factory.

[CalgaryZL1]

Finally got the lowers with the factory holes to put on rear black wing deflectors, and the car sits high enough in the rear to fit my Guinness! It’s was easier to pre install the new deflectors on the replacement arm before installation and didn’t require spacer that comes with the kit, that I didn’t realize they sold before I bought them individually. Now the hard part (due to laziness ) is taking the wheel off and cutting the dust shield.

[CalgaryZL1]

Originally Posted by TX18ZL1

LEDS…

First time she was on a left and I saw this handwriting from the factory… ideas?

Attachment 1144957

I don’t have any dial-in reference numbers on mine?

[speedyink1]

Not a lot to do here but wait for spring...



But at least I can feel better about theft in the mean time! These showed up today.
Amazing for my 2nd keyfob I leave in my house. A tad bulky for everyday carry but I'll make it work.

[The Maverick]

Originally Posted by SSShark

It comes as a package which covers an area 9" x 17'.
Consists of 68 tiles of each color. It just sits on top of the concrete, not stuck.

That looks good! I was thinking about having the whole garage done when I moved a couple years back, but other prioritie$ took precedence. Where did you pick that package up from? It included that edge and corner trim?

[arpad_m]

As an alternative, I bought RaceDeck CircleTrak tiles directly from the manufacturer, a 17' x 18' pad that I laid down in a standard size 20' x 25' garage cost $1500 including everything (tiles, edges and underlayment).

I'll also note that a circular surface pattern is much easier to clean that a diamond one, which I learned the hard way.

[SSShark]

Looks fantastic arpad_m. Great color combo. I went with Swisstrax Diamondtrax tiles.

[arpad_m]

Originally Posted by SSShark

Looks fantastic arpad_m. Great color combo. I went with Swisstrax Diamondtrax tiles.

Thank you very much. That product is the best when it comes to plastic garage floor tiles, Sir, great choice on your part as well I just had a super hard time keeping diamond pattern edges clean in my previous garage, that's why I went with a circular pattern this time.

[SSShark]

Originally Posted by arpad_m

Thank you very much. That product is the best when it comes to plastic garage floor tiles, Sir, great choice on your part as well I just had a super hard time keeping diamond pattern edges clean in my previous garage, that's why I went with a circular pattern this time.

It's only been a couple of weeks since I've had mine, but so far, so good. The finish seems to be very pretty easy to keep clean. I'll keep you posted as time goes by.

[sactownbwoy]

Because why not and it's mostly for car shows.

[keep_hope_alive]

printed the sound tube delete parts in ABS. Also printed a an engine coolant cover in ABS. Will install this week.



I have an O-ring for the intake manifold plug, and will use a butyl rope around the firewall plug.





the engine coolant cover could have benefitted from a raft as some of the internal tree supports came loose, but it's easy enough to clean up the underside that isn't seen anyway.

[ZPirate]

Picked my ZL1 up from having XPEL PPF installed on the front facia, the front lip, the headlights and the part of the front fenders closest to the front facia. I have the same set up on my 1LE and it has done a great job of protecting the front of the car.

[SSShark]

Originally Posted by ZPirate

Picked my ZL1 up from having XPEL PPF installed on the front facia, the front lip, the headlights and the part of the front fenders closest to the front facia. I have the same set up on my 1LE and it has done a great job of protecting the front of the car.

Hey ZPirate, pricey but man is that stuff is worth it