[Teer]

bumping this

Originally Posted by Teer

Anyone have a link to close up pics of the new side rocker kit? All the pics seem to be front to rear and i can't discern the look of the rockers.

[FNxR3DNECK]

Originally Posted by Teer

bumping this

The only shots I've seen are from that Sema car, haven't seen any close up shots.

[Teer]

Thanks FNxR3NECK. Link ?

[cellsafemode]

So a front fascia extension is a non-functional lip/splitter (most would then fall under this category). Do we need that kind of differentiation? just call it a lip or splitter.

Everytime i see this thread i keep thinking it's a cosmetic mod that puts the 2nd gen camaro front fascia on the 6th gen somehow. And everytime I am disappointed that it's just another lip to get scratched on speed bumps and crappy banked road driveways.

ok. rant over.

[Zylont]

Is the 2019, 2nd gen, GM fascia extension/splitter functional or is it open on the bottom like ACS and C7 Carbon ones?

Can someone post a pic of the underside of the 2nd gen GM splitter?

[carguy55]

The one on the 2017-18 SS 1LE is a closed bottom functional splitter, is the 2019 version the same?

[Umbriel]

Did a gloss black one ever get released? Or am I going to have to order one and have it painted or wrapped? I really hope not.

[Zylont]

Did anyone get a copy of this you could share?

“Instructions for installation of this part are available throughout GM Service information (S.I.) within the "Accessories Manual" section”

[EMTNLSS]

Originally Posted by Zylont

Did anyone get a copy of this you could share?

“Instructions for installation of this part are available throughout GM Service information (S.I.) within the "Accessories Manual" section”

I just got my splitter from the dealer today and noticed I need this also. It says to ask the dealer for the instructions so i'll probably go back and ask them for them.

[Umbriel]

Doesn't it just bolt on to the bottom using the existing bolts?

Sent from my SM-G955U using Tapatalk

[FNxR3DNECK]

Originally Posted by Umbriel

Doesn't it just bolt on to the bottom using the existing bolts?

Sent from my SM-G955U using Tapatalk

Yep it bolts right up, there should be 8 or 9 bolts plus 4 or 5 rivets in the box, just remove the corresponding bolts on the under side of the front bumper, line it up, stick it on with the tape and put the new bolts in (they have a bigger washer to support the splitter).

[Umbriel]

Originally Posted by FNxR3DNECK

Yep it bolts right up, there should be 8 or 9 bolts plus 4 or 5 rivets in the box, just remove the corresponding bolts on the under side of the front bumper, line it up, stick it on with the tape and put the new bolts in (they have a bigger washer to support the splitter).

Ok thanks. I am tired of waiting on a gloss black one so I think I am going to order the Mosaic black one order a Mosaic black spoiler so it matches.

[Zylont]

Here is what I found...

Front Bumper Fascia Extension Package Installation (Front Splitter Instruction ID:23301629)

Kit Contents
Qty Description
1 Front Bumper Fascia Splitter
12 Front Bumper Fascia Splitter Screws
4 Front Bumper Fascia Splitter Rivets
2 Alcohol Wipes
1 Installation Instructions

Tools Required
Drill, 4mm Drill Bit, Rivet tool

Procedure

1. Raise and suitably support the vehicle. Refer to Vehicle Service Manual.
2. Make sure the front fascia is at room temperature.
3. Clean the lower portion of the front fascia.
4. Remove and discard the 12 screws (1) along the front under side of the fascia.
5. Slightly loosen the remaining air deflector screws (1).
6. Clean the tape apply area (1) with the provided alcohol wipes.
7. On the front splitter, fold back the ends of the tape backing (1) so they stick out above the top edge.
8. Affix the front splitter (2) loosely to the front fascia using the 12 included screws (1).
   
   Note:*The front splitter should lie between the fascia and the LH/RH air deflectors (3).
   
   
9. Making sure that the front splitter (1) is centered on the front fascia and working from the center outward, carefully remove the backing of the tape strips.
10. Apply strong pressure all along the front splitter to make sure the tape adheres to the fascia.
11. Applying pressure to the front splitter to reduce gaps and working from center outward, tighten the 12 screws (2) that affix the front splitter to the fascia.
    
    Note:*Before continuing, inspect the front splitter for proper fit. Adjust and tighten lower screws as needed.
    
    
12. Tighten the remaining air deflector screws (1).
13. On the underside of the front splitter in the designated areas (1) drill four 4mm holes through the front splitter and into the front fascia.
14. Install the supplied rivets (2) into the drilled holes.
15. Inspect the front splitter for proper install.
16. Lower the vehicle.

[Bro_Im_Ramon]

hey guys i order the one from acs but its not a acs product .. its a gm product it has gm stamps all over it.... should i keep it or get my money back??? im just on the fence because i keep hearing the gm splitters are so fragile... no lie its hollow n weights zero to none.. im also confused because why would it be a gm product? i was expecting a acs design stronger n better?... someone give me some input please ... plus there site says nothing about a gm product???