ZLE rear driving camara. - Page 2

waterman · 03-21-2019, 04:50 PM

URBAN LEGEND · 03-21-2019, 06:24 PM

We need a plug and play for the front. We already have rear camera.

2SSRS@Gen5diy · 03-22-2019, 11:33 AM

Quote:

Originally Posted by URBAN LEGEND

We need a plug and play for the front. We already have rear camera.

We made one last year for that, but its not fro the 19 as there is an all new wiring in them.

~Jb · 03-22-2019, 04:29 PM

Did you consider the sharkfin like the GM prototype?

URBAN LEGEND · 03-22-2019, 05:28 PM

Quote:

Originally Posted by 2SSRS@Gen5diy

We made one last year for that, but its not fro the 19 as there is an all new wiring in them.

Oh.

SliChillax · 03-22-2019, 05:52 PM

Bookmarking this thread for more info

2SSRS@Gen5diy · 03-25-2019, 12:23 PM

Quote:

Originally Posted by ~Jb

Did you consider the sharkfin like the GM prototype?

We did, but its a pain to get out and run wires, dont know of many that will do the install, and that fin is ugly dont want it on my car. LOL

rlarsen462 · 03-25-2019, 01:35 PM

So we are not able to leave the bowtie in the factory location, it must be moved higher on the trunk lid to make this work? I think that will be a deal breaker for most considering it will probably require bodywork to fill in the hole left by the original bowtie, no?

waterman · 03-25-2019, 03:57 PM

Quote:

Originally Posted by rlarsen462

So we are not able to leave the bowtie in the factory location, it must be moved higher on the trunk lid to make this work? I think that will be a deal breaker for most considering it will probably require bodywork to fill in the hole left by the original bowtie, no?

The bowtie as well as all of the badges are secured by adhesive. There are no holes underneath. They are easy to remove with a heat gun (low setting) or a hair dryer and some fishing line.

rlarsen462 · 03-25-2019, 04:46 PM

Quote:

Originally Posted by waterman

The bowtie as well as all of the badges are secured by adhesive. There are no holes underneath. They are easy to remove with a heat gun (low setting) or a hair dryer and some fishing line.

Okay good deal... It was just large enough that I thought it might have screws behind it. Obviously a hole will need to be drilled in the new location for the camera wiring.

meSSohappy · 03-26-2019, 12:08 PM

Quote:

Originally Posted by 2SSRS@Gen5diy

We made one last year for that, but its not fro the 19 as there is an all new wiring in them.

Do you have a link to this front view camera for the 18s?

2out2sea · 03-26-2019, 02:26 PM

https://www.gen5diy.com/collections/...ision-8-screen

It's pricey, but I've been looking at it just for everything it offers and the fact that it integrates as factory installed.

2SSRS@Gen5diy · 03-26-2019, 04:03 PM

This is the link for your ZLE its the same kit in my car.

https://www.gen5diy.com/collections/...ckage-8-screen

~Jb · 03-27-2019, 01:27 PM

Would you sell the rear view camera kit without the rear spoiler? Basically everything and then just send the rear camera loose for modification?

03-21-2019, 04:50 PM	#15
waterman Drives: Grandad's C2 L89 Join Date: May 2017 Location: 2051.50N 15629.60W Posts: 1,711	__________________ 2018 ZL1 1LE sw/PDR

03-21-2019, 06:24 PM	#16
URBAN LEGEND Drives: 20 X3M CP & 19 ZL1 1LE A10 Join Date: Jun 2013 Location: Brenham, TX Posts: 3,517	We need a plug and play for the front. We already have rear camera. __________________ 🔺22 RS E TRON GT 🔺21 Model S Plaid

03-22-2019, 04:29 PM	#18
~Jb Drives: 2018 ZLE Join Date: Apr 2018 Location: Des Moines Posts: 227	Did you consider the sharkfin like the GM prototype? __________________ *2018 ZL1 1LE* (CARBON/PDR/NAV)**

03-27-2019, 01:27 PM	#28
~Jb Drives: 2018 ZLE Join Date: Apr 2018 Location: Des Moines Posts: 227	Would you sell the rear view camera kit without the rear spoiler? Basically everything and then just send the rear camera loose for modification? __________________ *2018 ZL1 1LE* (CARBON/PDR/NAV)**

03-22-2019, 05:52 PM	#20
SliChillax Drives: Camaro ZL1 A10, F-Type R, RR Sport Join Date: Jul 2016 Location: Albania Posts: 216	Bookmarking this thread for more info

03-25-2019, 01:35 PM	#22
rlarsen462 Sell Low, Buy High Drives: 2022 ZLE, 2023 ZLE (Inbound) Join Date: Feb 2019 Location: Varies Posts: 542	So we are not able to leave the bowtie in the factory location, it must be moved higher on the trunk lid to make this work? I think that will be a deal breaker for most considering it will probably require bodywork to fill in the hole left by the original bowtie, no?

03-26-2019, 02:26 PM	#26
2out2sea Drives: 2018 hyper blue ZL1 1LE Join Date: Nov 2018 Location: Alabama Posts: 165	https://www.gen5diy.com/collections/...ision-8-screen It's pricey, but I've been looking at it just for everything it offers and the fact that it integrates as factory installed.

03-26-2019, 04:03 PM	#27
2SSRS@Gen5diy Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008 Location: By the lake in AZ Posts: 15,719 View My Garage	This is the link for your ZLE its the same kit in my car. https://www.gen5diy.com/collections/...ckage-8-screen

User Name		Remember Me?
Password