Homepage Garage Wiki Register Social Groups Calendar Search Today's Posts Mark Forums Read
#Camaro6
Go Back   CAMARO6 > CAMARO6.com General Forums > ZL1 Discussions


AWE Tuning


Post Reply
 
Thread Tools
Old 11-10-2021, 12:08 AM   #1
Kavik830
 
Drives: 2018 ZL1
Join Date: Nov 2021
Location: OR
Posts: 3
Post ZL1 sc pulley, tuning, nightmare

I’m very new to this forum or any forum.
I recently hired a shop to do modifications to my 2018 ZL1. I have a few learning challenges and a when I found a place that helps veterans I was really excited. Now I sit trying to figure out how to repair their modifications. My own fault for not researching.
I hired them to install kooks headers w/high flow cats, upper supercharger pulley, tune, and exhaust mod. All by their recommendation.
I found out later they had cut my sc pulley off, putting six cuts into my sc snout w/o telling me. Then heating the new pulley hub up and putting it on. This procedure was never discussed prior. Not exactly sure how they heated it nor how many times they tapped or hammered it into place. All I know is I hear a new sound from my sc, which they say they can’t hear. If they heated it while on sc shaft could have dried up bearing grease causing premature failure I learned. Did they damage the three pins in the back?
I learned about the right way to r/r pulley hub is with press. Ironically the hub has printed on it “press on only.”
I took the pulley off and found fine metal dust around sc shaft.
I realize I should have researched more which is my fault. Oh I said that already. Just hope it sticks in my memory for any future stuff.
It made me suspect when the final bill was increased $562 due to a (parts/labor matrix change) they’d lost my original estimate. This was same amount of my veteran discount they gave. After I showed them my copy they then added the cost of tuning pcm license lock and tune fee, they forgot to add to original, which was $562.
On the day I came to pick it up, they called told me they had damaged my car when moving it. I was a bit shocked and while taking it to body shop I smelled burning smell. They said normal for new headers. Found out the header on drivers side was melting the plastic cover on my steering shaft. Eventually I called kooks and I think they’re working with me if I show them proof of purchase. So when I looked at the box they gave me with my old manifolds I discovered it was a box for dodge truck.
I’m trying to find out what to do about my sc snout. How to take the snout off to have it checked since metal dust was all around the shaft and bearing. I also wonder if I need a new sc snout.
I’m very fortunate to have this car. Prior to this I had extended warranty which I knew I was risking by getting this. I didn’t know that they were going to put 50 miles on my car also when tuning. I thought i asked many questions and was under impression that tuning was computer related and later dyno was driving part. But I learned that’s how a “street tune” is done w/o dyno. Which I haven’t received any documentation about the tune from them.
The sc pulley is a griptec 2.30” and the shop said i don’t need a different belt but when I called griptec they recommended I get a green belt.
I apologize about the long rant. I’m grateful that I didn’t keep driving it possibly causing more damage from this mess.
If anyone can learn to not just check out a shop prior to any work but also what is exactly involved in the work theyll be doing, well I hope it prevents this from happening to anyone else.
I know how naive and stupid I was and feel like crap. I was hoping to drive it in our Veterans Day parade but maybe Memorial Day.
I have learned allot though.
Thanks

Last edited by Kavik830; 11-14-2021 at 02:38 AM. Reason: Adding photos
Kavik830 is offline   Reply With Quote
Old 11-10-2021, 12:48 AM   #2
BlaqWhole
Account Suspended
 
Drives: 2017 Camaro ZL1 A10
Join Date: May 2012
Location: NJ
Posts: 7,692
I'd like to know the name of this shop.
BlaqWhole is offline   Reply With Quote
Old 11-10-2021, 06:30 AM   #3
LT4Greg


 
LT4Greg's Avatar
 
Drives: 2017 Camaro ZL1 Coupe
Join Date: May 2016
Location: Georgia
Posts: 4,886
Wow did they do a job on you and your ZL1! Good luck to you.
__________________
ZL1 Coupe, PDR, Exposed carbon fiber hood insert, My Link with Nav, M6 6 speed and Silver Ice Metallic. Mods done: ceramic window tint, GM Accessories Camaro floor mats and Roto-Fab CAI.
LT4Greg is offline   Reply With Quote
Old 11-10-2021, 06:43 AM   #4
EDFHOBBIES
Dyno Show Queen LOL
 
EDFHOBBIES's Avatar
 
Drives: 16 SS & 17 ZL1 Both Yellow
Join Date: Jan 2014
Location: Houston
Posts: 4,050
Send a message via Skype™ to EDFHOBBIES
If it needs repairing I would contact kong or jokerz then send bill to the shop. If they don't pay "Charge back or file a law suite". While the blower is being repaired have them port it! The blower comes off very easy so you won't have any labor costs. There is a video by Katech on how to remove the blower even a chimpanzee could remove it! The hard part will be filling the blower coolant up and even then its not that hard all that is covered by the video or this could be the time to install a reservoir for easy filling or adding a bumper tank for extra capacity. While its off add a catch can Mighty mouse has a great video on this to where they stuck a roll of tape under the blower to get to the PCV valve. Since the blower is off it be cake for the pcv!

The shop should of pulled the blower, taken snout off, and pressed the pulley off. I myself would of done cut trick but i have a lot of experience doing stuff like this since I'm constantly removing bearings of rusted shafts where the jaws on the puller bend or snap. 1 thin hair line cut parallel with the shaft shouldn't cause any problems. 6 multiple directions making 900 hp with a tight belt maybe so...
__________________


Kong Ported 2650, Crawford Racing Port Injection, Weapon X 112mm Adapter, NW112mm TB, Livernois Ported LT4 Heads, Lingenfelter GT32 stealth cam, Haltech Elite, and Carbon by Trufiber

Last edited by EDFHOBBIES; 11-10-2021 at 08:36 AM.
EDFHOBBIES is offline   Reply With Quote
Old 11-10-2021, 10:06 AM   #5
BlaqWhole
Account Suspended
 
Drives: 2017 Camaro ZL1 A10
Join Date: May 2012
Location: NJ
Posts: 7,692
Please keep us updated.
BlaqWhole is offline   Reply With Quote
Old 11-14-2021, 03:53 AM   #6
Kavik830
 
Drives: 2018 ZL1
Join Date: Nov 2021
Location: OR
Posts: 3
Pictures

I added these pics of just some of the things I noticed. The hub and part of the snout looks yellowish. Someone said overheating it probably discolored it. I’m getting it checked hopefully soon.
Attached Images
          
Kavik830 is offline   Reply With Quote
Old 11-14-2021, 05:56 AM   #7
Joshinator99


 
Joshinator99's Avatar
 
Drives: 2017 Camaro 2SS A8
Join Date: Aug 2018
Location: Petersham MA
Posts: 2,569
Good lord…sorry to see this. Good luck getting it all fixed. Please do your fellow Camaro6 members a favor and name the shop.
__________________
2017 Chevy Camaro 2SS A8 Kong ported Whipple 8.00/3.00, Mast Black Label heads, Fore triple in-tank pumps, 229/245 cam, Rotofab Big Gulp, 112mm TB, forged pistons & rods, LPE +52% injectors, LPE BB HPFP, AWE CB, GForce DS & axles, 2” coated headers, MM Wild CC, everything BMR makes, OEM 1LE wheels (street), Forgestar D5 bead locks (track). 927 WHP/917 WTQ, 9.65@146
2021 Ford Expedition Limited 4WD (daily driver)
2018 Alfa Romeo Giulia Ti Sport Q4 (hers)
Joshinator99 is online now   Reply With Quote
Old 11-14-2021, 06:15 AM   #8
CW3SF

 
CW3SF's Avatar
 
Drives: 2019 Chevy Camaro ZL1 M6
Join Date: Jul 2019
Location: Denver
Posts: 910
Wow they really hacked your car up. I second the above post, please name this shop before someone else gets the same treatment.
__________________
On the Korn
Kong Stage X Port, LPE Big Bore HPFP, Big Gulp, NW103, XDI +30 Injectors, ARH Coated Headers, dual X-pipes, MBRP resonators, AWE Touring, FlexFuel, JMS Booster, Elite E2-X CC and ADMv2 Reservoir. Stock motor, stock heads, stock cam, stock pulleys 714/661 SAE
CW3SF is offline   Reply With Quote
Old 11-14-2021, 07:27 AM   #9
LiqTenExp

 
LiqTenExp's Avatar
 
Drives: 2017 ZL1
Join Date: Jan 2017
Location: NJ
Posts: 764
That is an impressive amount of fail for 1 shop to create. 3rd the above request.
__________________
2017 Camaro ZL1 Coupe M6 (847whp on Dynojet)
LiqTenExp is online now   Reply With Quote
Old 11-14-2021, 07:59 AM   #10
laynlo15
 
laynlo15's Avatar
 
Drives: 2022 Lt1 A10
Join Date: Nov 2015
Location: clark, mo
Posts: 7,141
They shouldn't be working on anyone's Camaro, Vette or even a POS. Should be out of business.
__________________
2022 Lt1 6.2 A10, Phastek Splitter, E85, Roto Fab- phdtuning-11.79@121 2022- Ltz 3.0 Duramax Silverado
16SS w/2650 9.41@147sold x-maggie employee-
16 C7 10.90@128 sold
laynlo15 is offline   Reply With Quote
Old 11-14-2021, 09:41 AM   #11
SJFGTO
Oh Oh it's Friday Night!
 
SJFGTO's Avatar
 
Drives: 2018 ZL1 1LE Nightfall Gray
Join Date: Jan 2018
Location: Walton Woods
Posts: 974
That is just plain awful. That level of incompetence and dishonesty needs to be exposed, I hope you name this shop. Best of luck getting it fixed, its fixable for sure, that shop should pay the bill.
__________________
2018 Camaro ZL1 1LE NFG; ARH 2” headers, catless mids, ARH full exhaust, Lingenfelter 18% lower pulley, ATI Harmonic Balancer, Roto-fab CAI, EE-catch can, TM ported TB, NX Lid, BMR strut tower brace. Aeroforce dual pod interceptor gauges. Tuned by Vengeance Racing!!! 644 HP @ 6250 rpm / 689 trq @ 3660 rpm

Four that wanna own me
Two that wanna stone me
One says she's a friend of mine...
SJFGTO is offline   Reply With Quote
Old 11-14-2021, 09:42 AM   #12
CamOnlyJabroni
 
CamOnlyJabroni's Avatar
 
Drives: 19’ ZL1/16’ C7Z/96’ Camaro Z28
Join Date: Apr 2021
Location: Fort Wayne, IN
Posts: 111
Definitely name the shop. X2 on shipping the blower out to be inspected and rebuilt at shops expense.
CamOnlyJabroni is offline   Reply With Quote
Old 11-14-2021, 11:02 AM   #13
Revalot
 
Drives: ZL1/1LE parts added
Join Date: May 2018
Location: Somewhere around Texas pines tress and smooth asphalt
Posts: 487
OMG !
Revalot is offline   Reply With Quote
Old 11-14-2021, 11:53 AM   #14
Snowwolfe
 
Drives: 2020 ZL1 A10
Join Date: Feb 2020
Location: East TN
Posts: 418
Curious as to why you decided to join and post your nightmare on this forum AFTER everything went wrong.
Why didnt you join and ask questions and do some research prior to having a "unnamed" shop do all this work?
Snowwolfe is offline   Reply With Quote
 
Post Reply

Tags
headers, supercharger pulley, tune mod, zl1

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:51 PM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2022, vBulletin Solutions, Inc.