05-30-2020, 07:26 PM | #1 |
Drives: 2016 Black 2ss Join Date: Aug 2018
Location: Atlanta
Posts: 54
|
For those using a Proclip
Does the phone holder need to be really tight to keep your phone from falling while driving, or can I leave it loose enough to easily slide the phone in and out? I have it tight enough right now that I need to use two hands to put it in and take it out.
|
05-30-2020, 08:38 PM | #2 |
Banned
Drives: 2019 1SS Convertible Join Date: Jun 2019
Location: Oxford, NC
Posts: 183
|
That would be too tight. Mine is adjusted so that the phone can easily settle into proper position under its own weight.
|
05-30-2020, 08:43 PM | #3 |
Two Lane Blacktop
Drives: '18 Camaro 2SS Join Date: Jul 2019
Location: Black River, NNY
Posts: 516
|
Just needs some slight tension
|
05-30-2020, 10:03 PM | #4 |
Drives: '17 ZL1 A10 Vert Join Date: Mar 2017
Location: SW Florida
Posts: 375
|
I have the dash mount. It’s loose enough so that the phone slides in and out pretty easily. The only way the phone will ever “fall” out is if my car is upside down.
You just need to adjust it a bit. |
05-31-2020, 01:25 AM | #5 |
Drives: 19’ Camaro SS 1LE Join Date: Nov 2016
Location: SoCal
Posts: 309
|
You’ve got it too tight. You just need to fine tune it, to make sure it’s not too loose.
__________________
2019 Camaro SS 1LE
|
05-31-2020, 08:23 PM | #6 |
Drives: 2016 Black 2ss Join Date: Aug 2018
Location: Atlanta
Posts: 54
|
Thanks for the suggestions!
|
06-01-2020, 04:54 PM | #7 |
Drives: 18 zl1 Join Date: Aug 2017
Location: central alabama
Posts: 935
|
can you share some pics of this one? I was on the fence about it, but ultimately decided for the other one due to possible permanent marking the dash.
|
06-03-2020, 09:11 PM | #8 |
Drives: 2020 Camaro 2SS Rally Green Join Date: May 2020
Location: Novi, MI
Posts: 32
|
I have the exact same concern. The destructions suggest levering open a join in the dash to insert the ProClip. Does that leave a mark?
|
06-04-2020, 06:45 AM | #9 |
Drives: 2016 Camaro 2SS Hyper Blue Metallic Join Date: May 2020
Location: WI
Posts: 2,451
|
My concern is more along the lines of once you mess with the factory seam on any of these dash parts you always seem to develop a squeak. You are spreading apart that seam to insert that clip (all be it just a little bit) but has anyone developed a squeak from doing so?
|
06-04-2020, 09:09 AM | #10 |
Drives: '17 ZL1 A10 Vert Join Date: Mar 2017
Location: SW Florida
Posts: 375
|
This is a pic looking straight down from above so you can see the seam where the mount attaches.
I've had it installed for over two years. No rattles or squeaks. |
06-04-2020, 01:44 PM | #11 | |
Drives: 19’ Camaro SS 1LE Join Date: Nov 2016
Location: SoCal
Posts: 309
|
Quote:
Your mount, does it interfere with your turn signal stalk?
__________________
2019 Camaro SS 1LE
|
|
06-04-2020, 05:53 PM | #12 |
Drives: '17 ZL1 A10 Vert Join Date: Mar 2017
Location: SW Florida
Posts: 375
|
It’s close, but no. It doesn’t get in the way of the turn signal stalk.
Sorry - pics got rotated posting from my phone. |
06-04-2020, 10:56 PM | #13 | |
Drives: 19’ Camaro SS 1LE Join Date: Nov 2016
Location: SoCal
Posts: 309
|
Quote:
Nice to see a close up visual of that mount on the dash.
__________________
2019 Camaro SS 1LE
|
|
06-05-2020, 06:25 AM | #14 |
Drives: 2016 Camaro 2SS Hyper Blue Metallic Join Date: May 2020
Location: WI
Posts: 2,451
|
|
|
|
Post Reply
|
Thread Tools | |
|
|