Homepage Garage Wiki Register Members List Social Groups Calendar Search Today's Posts Mark Forums Read
#Camaro6
Go Back   CAMARO6 > Engine | Drivetrain | Powertrain Technical Discussions > Transmissions


JUICEDMOTORSPORTS


Post Reply
 
Thread Tools
Old 04-29-2019, 02:16 PM   #1
Whatwarranty
 
Drives: 2016 camaro ss
Join Date: Apr 2018
Location: Texas
Posts: 42
Axles GForce install removal

Installing GForce outlaw axles. I can not seem to get the axle out of the diff I have pry bar and am putting so much into it the car was coming off the jack stands. Any one have any tricks because strength isn’t doing it lol.
Whatwarranty is offline   Reply With Quote
Old 04-29-2019, 02:37 PM   #2
Jhunsberger
 
Jhunsberger's Avatar
 
Drives: 2017 Camaro 1SS M6
Join Date: Oct 2016
Location: 19518
Posts: 287
I did some DSS axles over the winter. The axle does not come out of the diff. You want to remove the 6 or 8 bolts at the diff end of the axle. The stock ones came out without pulling any of the suspension apart, with a little finesse. The new ones would not go in the same way. Ended up pulling the 2 outer suspension connections apart above the rear hub to get a little more room to slide the diff end of the axles in.
__________________
2017 1SS M6 Hyper Blue Metallic NPP, MMR 228 Z/28 replica wheels, Front: 20 x 9, Rear 20 x 11

Stock: 416hp/427tq, 12.21 @ 116.80

Modified 02/2019: Whipple SC w/ 3.500 pulley, LT4 fueling, NW 103 TB, Roto-Fab Big Gulp, Kooks 2" jet coated, full Borla ATAK exhaust, DSS axles, Gforce driveshaft.

Tuned by Complete Street Performance 653hp/618tq

Best 1/4 to date: 10.705 @ 131.92
Jhunsberger is offline   Reply With Quote
Old 04-29-2019, 02:50 PM   #3
Whatwarranty
 
Drives: 2016 camaro ss
Join Date: Apr 2018
Location: Texas
Posts: 42
GForce isn’t like those ones they actually go into the diff
Whatwarranty is offline   Reply With Quote
Old 04-29-2019, 03:23 PM   #4
Jhunsberger
 
Jhunsberger's Avatar
 
Drives: 2017 Camaro 1SS M6
Join Date: Oct 2016
Location: 19518
Posts: 287
Oh get out, didnt realize they did them different. Well best of luck to you!
__________________
2017 1SS M6 Hyper Blue Metallic NPP, MMR 228 Z/28 replica wheels, Front: 20 x 9, Rear 20 x 11

Stock: 416hp/427tq, 12.21 @ 116.80

Modified 02/2019: Whipple SC w/ 3.500 pulley, LT4 fueling, NW 103 TB, Roto-Fab Big Gulp, Kooks 2" jet coated, full Borla ATAK exhaust, DSS axles, Gforce driveshaft.

Tuned by Complete Street Performance 653hp/618tq

Best 1/4 to date: 10.705 @ 131.92
Jhunsberger is offline   Reply With Quote
Old 04-29-2019, 03:31 PM   #5
Vtor_ZL1

 
Vtor_ZL1's Avatar
 
Drives: 18 ZLE
Join Date: May 2018
Location: Left Side of the Moon
Posts: 773
Then you may need to remove diff cover and remove the clips holding axles end in place most likely. There few folks that changed rear ends and some that upgraded axles - check their how-to, IIRC, one was a video.
__________________
ing for grip.


Are you in the NY/NJ/PA/CT region? Join us for autox fun at MetLife Stadium. HUGE lots, tons of runs. Next Event May 25 - Lot L

http://www.motorsportsne.com/

Register online or just show up and spectate, which is FREE! Organize a group of 5 or more, get $10 off your first event for each driver.
Vtor_ZL1 is offline   Reply With Quote
Old 04-29-2019, 05:24 PM   #6
Whatwarranty
 
Drives: 2016 camaro ss
Join Date: Apr 2018
Location: Texas
Posts: 42
GForce said just to pry on them when I called. So guess I’ll have the stock axles until they break because they are not budging at all. Even put a tow strap on other vehicle and axle ��.
Whatwarranty is offline   Reply With Quote
Old 04-29-2019, 05:35 PM   #7
Whatwarranty
 
Drives: 2016 camaro ss
Join Date: Apr 2018
Location: Texas
Posts: 42
Ok tried one last time with strap and hammer and pry bar it came out .
Whatwarranty is offline   Reply With Quote
Old 04-30-2019, 05:11 AM   #8
Jhunsberger
 
Jhunsberger's Avatar
 
Drives: 2017 Camaro 1SS M6
Join Date: Oct 2016
Location: 19518
Posts: 287
Nice work! A tow strap and another vehicle sounded a little risky.....
__________________
2017 1SS M6 Hyper Blue Metallic NPP, MMR 228 Z/28 replica wheels, Front: 20 x 9, Rear 20 x 11

Stock: 416hp/427tq, 12.21 @ 116.80

Modified 02/2019: Whipple SC w/ 3.500 pulley, LT4 fueling, NW 103 TB, Roto-Fab Big Gulp, Kooks 2" jet coated, full Borla ATAK exhaust, DSS axles, Gforce driveshaft.

Tuned by Complete Street Performance 653hp/618tq

Best 1/4 to date: 10.705 @ 131.92
Jhunsberger is offline   Reply With Quote
Old 05-15-2019, 06:13 AM   #9
laynlo15

 
laynlo15's Avatar
 
Drives: 2016 1ss A8, Npp
Join Date: Nov 2015
Location: clark, mo
Posts: 4,651
Great, let us know if you get them back in ok.
__________________
2016 Camaro 1SS, Magnuson Heartbeat, NW103, Roto Fab Big Gulp, Manley Pistons/Rods, Livernois Cam, BBK, RPM RB,
Kents Hot Rods, M/T & Race Star Wheels, Makes a little HP 1/4 mile 9.83@140 w/1.40 60ft & 6.33@112 1/8 mile Magnuson Employee and Team Driver
laynlo15 is offline   Reply With Quote
 
Post Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:14 PM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2019, vBulletin Solutions, Inc.