01-16-2019, 10:43 AM | #29 |
Drives: 2016 1SS NFG A8 Join Date: Aug 2017
Location: 46804
Posts: 6,800
|
I don't know...the P1x car Brett did that ran 10.0 @ 138 could be done for 10-12k and would be right with the heads/cam setup in ET but trap a little higher. Actually that car went 10.0 with jackep up shift points...had the guy pushed the combo further it would of went 9's and that is with no weight pulled. You have to keep in mind that these fast bolt-on and heads/cam cars are pulling a good amount of weight to run the times they are where most FI setups are just adding power and weight from the Supercharger kit. I would love to see Brett take a FI car the distance he has with some of the NA stuff so we can get a really good comparison.
__________________
2016 NFG 1SS A8
Options-2SS Leather/NPP Perf. mods-Whipple 2.9/Fuel System/Flex Fuel/103mm TB/Rotofab Big Gulp/Cat Deletes/Corsa NPP Per. times- 10.5 @ 137 w/ 1.8 60ft Full weight on 20's 1200DA |
01-16-2019, 01:05 PM | #30 |
Drives: 2015 C7 Z06 M7 Join Date: Dec 2012
Location: So-Cal
Posts: 654
|
If you can DIY, this will fall in the price range:
https://youtu.be/bdJz6CJALtU If I was to do it again it would be even easier: Magnuson 2300 with 75mm pulley 7000 LT4 pump / injectors - 1500 102mm Nick Williams Throttle Body - 650 Water/meth system - 500 Tune - 400 |
01-16-2019, 01:39 PM | #31 |
Drives: 2022 Lt1 A10 Join Date: Nov 2015
Location: clark, mo
Posts: 8,860
|
If you have someone install it
Maggie 7000, labor 1000, Race star/hoosier drag pack 1600, tune 400 and run 10.80@129 like mine did. 10,100.00
__________________
2022 Lt1 6.2 A10, Maggie 2300, THPSI Port Inj/10 rib, Rotofab, E, Nickey, SCOL, Griptech, RC Bandits, Hoosiers/MT 9.80@142.96 1.44 60ft, 6.34@112 707/669 RWHP/TRQ. 16SS Maggie 2650 9.41@147 1.35 60ft, 5.99@119. 16 C7 A8 10.90@128 Bolt on stuff
|
01-16-2019, 02:50 PM | #32 |
Drives: 2022 Lt1 A10 Join Date: Nov 2015
Location: clark, mo
Posts: 8,860
|
I ran my 10.03@138 at full weight plus since I'd put my 6 pt cage in. I was about 50 lbs over stock even with the back seat out but still had my front passenger seat in. Well did have the drag pack as most everyone else does on the fast list for modified cars or FI
__________________
2022 Lt1 6.2 A10, Maggie 2300, THPSI Port Inj/10 rib, Rotofab, E, Nickey, SCOL, Griptech, RC Bandits, Hoosiers/MT 9.80@142.96 1.44 60ft, 6.34@112 707/669 RWHP/TRQ. 16SS Maggie 2650 9.41@147 1.35 60ft, 5.99@119. 16 C7 A8 10.90@128 Bolt on stuff
|
01-16-2019, 03:48 PM | #33 | |
Drives: 2016 1SS NFG A8 Join Date: Aug 2017
Location: 46804
Posts: 6,800
|
Quote:
__________________
2016 NFG 1SS A8
Options-2SS Leather/NPP Perf. mods-Whipple 2.9/Fuel System/Flex Fuel/103mm TB/Rotofab Big Gulp/Cat Deletes/Corsa NPP Per. times- 10.5 @ 137 w/ 1.8 60ft Full weight on 20's 1200DA |
|
01-17-2019, 06:55 AM | #34 |
Drives: 2022 Lt1 A10 Join Date: Nov 2015
Location: clark, mo
Posts: 8,860
|
Imagine if I hadn't had a broken ring land also, that happened the same weekend on number 1 cylinder when it pushed the front seal out.
__________________
2022 Lt1 6.2 A10, Maggie 2300, THPSI Port Inj/10 rib, Rotofab, E, Nickey, SCOL, Griptech, RC Bandits, Hoosiers/MT 9.80@142.96 1.44 60ft, 6.34@112 707/669 RWHP/TRQ. 16SS Maggie 2650 9.41@147 1.35 60ft, 5.99@119. 16 C7 A8 10.90@128 Bolt on stuff
|
|
|
Post Reply
|
|
|