You are browsing camaro6 
02-13-2021, 11:19 AM
|
#1 |
|
Jiyuu
Drives: Camaro LT 2016 Join Date: Feb 2021
Location: Yuba City
Posts: 7
|
BCM / Tail light issues
Joined forum looking for some technical help with my 2016 LT.
2016 LT. Changed out tail lamps with LED lamps. I am aware that I will need to install the resistors or harness/with resistor. My current issues are: (1) The driver side signal does not work at the tail light. The blinker on the console works 3 times normal speed then hyper flashes with matching blinker sound. The passenger side blinker does work with the same 3 blink hyper flash. (2) The running light on the passenger side tail light does not work. The driver side running light does work. I have confirmed the ground from each plug is good (pins 4 and 6). I have also confirmed continuity from the plug to the BCM. Driver turn signal (plug pin 1. BCM X5-1) and passenger side running light (plug pin 5. BCM X5 -7) Driver side blinker at plug pin #1 no voltage with blinker on. (Console blinker and sound on with hyper flash as mentioned above). Passenger side running light at plug pin #5 no voltage with light switch on. I swapped the driver side and passenger side tail lamp assemblies and same problem above exists (so not a tail lamp assembly problem). Also disconnected the battery over night to reset BCM. Problem still present. I would think that installing the resistors or harness/with resistor will not resolve the left blinker or right running light not working? That leaves the BCM as bad or does anyone have any other potential items I may need to troubleshoot? Thanks for any assistance! |
|
|
|
02-15-2021, 01:13 AM
|
#2 |
 
Drives: 2016 Chevy Camaro 2SS Join Date: Aug 2012
Location: Atlanta, GA
Posts: 289
|
Check the fuses
|
|
|
|
|
02-17-2021, 11:46 AM
|
#3 |
|
Jiyuu
Drives: Camaro LT 2016 Join Date: Feb 2021
Location: Yuba City
Posts: 7
|
Thanks. Funny I did that but found I checked the wrong fuse. Checked correct fuse and it was blown. Replaced and blew again. Found wire connector between fuse block and BCM bad.
|
|
|
|
|
09-05-2021, 01:41 AM
|
#4 | |
 Drives: 2016 Camaro SS Join Date: Aug 2021
Location: San Jose, Ca
Posts: 1
|
Quote:
|
|
|
|
|
|
09-07-2021, 11:03 AM
|
#5 |
 Drives: Camaro 1SS A8 Vert Join Date: Sep 2018
Location: Tx
Posts: 303
|
Put it back stock and see what it does....
|
|
|
|
|
04-21-2023, 09:01 PM
|
#6 | |
 Drives: 2019 1LE/ss 2014 ss/rs summit white Join Date: May 2016
Location: Charlotte
Posts: 131
|
Quote:
__________________
2019 ss/1LE d1x, LT4 fuel System, Triple meth nozzle, ported BTR, 2” Texas speed headers, Built 377 SPDC motor, CTporting heads, TooHighPsi port system, SMG aux.
1014/800 on E55/meth 890/750 on 93/meth Working on tuning the port system for full e. With questions just message me here for a faster response. https://www.facebook.com/eric.willia...ibextid=LQQJ4d |
|
|
|
|
|
04-23-2023, 07:52 AM
|
#7 | |
         Drives: 2017 2SS, 50th pkg, M6, MRC, NPP Join Date: Jan 2016
Location: Ocean City, NJ
Posts: 3,175
|
Quote:
LED installs can be weird on this car. I believe cellsafemode is our guru on these matters. I think there are some paths to ground which may need to be addressed. |
|
|
|
|
|
|
|
|
|
Post Reply
|
|
|
