12-04-2018, 06:05 PM | #43 |
Drives: 2016 2SS 8AT Join Date: May 2018
Location: Nevada
Posts: 358
|
So it does look like the lt1 is a little thinner. Is that correct? If so, that would mean the lt1 might sit a little lower in the valley. That would mean the height measurement would be better from the top to the top of a port.
|
12-04-2018, 07:26 PM | #44 |
Drives: 2017 LT1 Join Date: May 2018
Location: Iowa
Posts: 44
|
Yes the belly is lower on the LT1 intake and the L86 intake the ports were touching not the belly (not by much) on that 8.375" measurement.
|
12-05-2018, 05:29 AM | #45 |
Drives: 2018 Audi TT RS Join Date: Jan 2014
Location: Navarre, Florida
Posts: 1,915
|
Hmm. I’m not sure if that’s going to fit at all then. Let’s hope someone has some sitting around to test out fitment.
__________________
2018 Audi TT ▊RS
2.4X 0-60, 1.6X 60', 120+mph 1/8th, 4.XX 60-130, 150+mph traps on 255/35/18 R888R tires on the street (unprepped). 2019 Audi RS3 About as fast as the TT RS 2019 Camaro ZL1 1LE Sold 2018 Camaro SS 1LE Sold 2019 Corvette Z06 Sold 2021 Charger Hellcat Redeye Widebody Sold |
12-05-2018, 05:54 AM | #46 |
Drives: 6th gen Join Date: Aug 2013
Location: US
Posts: 3,664
|
I have a crazy week but I’ll get the measurements Saturday from the lt1.
__________________
‘22 2SS 1LE M6 Summit White - RF, Flexfuel, LT2 intake, 95mm tb, ATI udp, VT ramair, full 28” dragpack - 11.68@122
‘16 1SS M6 LT2 intake + boltons on DR 11.0@126+ (Sold) |
12-05-2018, 10:07 AM | #47 |
Drives: SS 6 speed of course Join Date: Jan 2016
Location: Hilo, HI
Posts: 4,316
|
The measurement is from bottom of the manifold at the head seat face(port) to the top. IMO it is just as easy to measure from top of the actual intake port to peak of the runner.
__________________
Forged short block, large duration sub .600 lift Cam Motion cam, 7200 RPM fuel cut, Pray Ported Heads, 3.85 pulley D1X, stage II intercooler, DSX secondary low side, DSX E85 sensor, Lingenfelter big bore 2.0 pump, ported front cats, 60608 Borla, LT4 injectors, ZL1 1LE driveshaft and Katech ported TB, ported MSD intake, BTR valvetrain, ARP studs, ProFlow valves, PS4 tires.
|
12-05-2018, 10:40 AM | #48 |
Drives: 2017 LT1 Join Date: May 2018
Location: Iowa
Posts: 44
|
|
12-05-2018, 02:51 PM | #49 |
SoCal HT5! SD
Drives: 2016 red hot 2ss M6 Join Date: Nov 2011
Location: San Diego CA,
Posts: 1,929
|
__________________
http://www.camaro5.com/forums/showth...37#post5437037
By my deeds, I honor him. V8!!! |
12-05-2018, 03:17 PM | #50 |
Drives: My Dad's car is a '16 1SS 6MT Join Date: Jul 2016
Location: Menifee CA
Posts: 76
|
Someone should test this with an FBO car and see what the differences are.
|
12-05-2018, 04:50 PM | #51 | |
Drives: 2017 LT1 Join Date: May 2018
Location: Iowa
Posts: 44
|
Quote:
Roof of port to top of intake = 7" with a level Top of intake port to top of intake = 6.25" with a level |
|
12-05-2018, 04:57 PM | #52 |
Drives: 6th gen Join Date: Aug 2013
Location: US
Posts: 3,664
|
That measurement aligns with where I measured Saturday.
Should give 0.5” of clearance to the hood insulation
__________________
‘22 2SS 1LE M6 Summit White - RF, Flexfuel, LT2 intake, 95mm tb, ATI udp, VT ramair, full 28” dragpack - 11.68@122
‘16 1SS M6 LT2 intake + boltons on DR 11.0@126+ (Sold) |
12-05-2018, 06:07 PM | #53 |
Drives: 2016 2SS 8AT Join Date: May 2018
Location: Nevada
Posts: 358
|
Snow has my hood frozen right now or I'd look, is there any issue with the cowl maybe hitting It and not the hood or do you think it will sit far enough forward not to bother
|
12-06-2018, 11:49 AM | #54 |
Drives: 2016 2SS 8AT Join Date: May 2018
Location: Nevada
Posts: 358
|
Well I got a good deal for one on eBay so I'll try it. Dont know how soon it will be as I have no shop and it's been super cold and snowy.
|
12-06-2018, 01:43 PM | #55 |
Drives: 2016 2SS Join Date: Jul 2016
Location: Sanford NC
Posts: 2,766
|
Interesting. I did a ported L86 IM and 95mm for a guys a bit back that had a ported MSD on his truck. I never go the results back. I am wondering if this is the same guy.
__________________
2016 2SS. H/C SBE 1.37 60ft, 6.36@109.49, 9.97@136+. Nuff Said.
|
12-06-2018, 02:08 PM | #56 | |
Drives: 2016 2SS 8AT Join Date: May 2018
Location: Nevada
Posts: 358
|
Quote:
What's your thoughts on this? |
|
|
|
Post Reply
|
Thread Tools | |
|
|