11-23-2018, 05:46 PM | #1 | |
Drives: 2019 2SS Join Date: Mar 2018
Location: Ohio
Posts: 103
|
2019 Camaro Tow Hook Install?
I bought a 2019 2SS on Wednesday and I would like to install tow hook license plate holder that zl1 addons sells but I couldn't figure out how to remove that little part of the grill like shown in this video
Does anybody know how to do it? Here is a picture of the grill. I don't see any way to remove it. Last edited by ste1n; 11-23-2018 at 06:09 PM. |
|
11-23-2018, 10:24 PM | #2 |
Drives: 2017 SS 1LE, 2017 Volt, 2013 Pilot Join Date: May 2014
Location: Colorado
Posts: 4,274
|
Pull / pry down from the top, just under the solid black part of grill. you will see a small pry slot if you need it but i can get mine with just fingers.
__________________
2017 SS 1LE | HBM | Vortech V3-Si supercharger (620RWHP and 575ft lbs) | PDR | Black Bowties | Illuminated Front Black Bowtie | Illuminated Door Sills | Smoked Tails | vented seats mod
Last edited by DenverTaco07; 11-23-2018 at 10:41 PM. |
11-24-2018, 08:31 PM | #3 |
Drives: 2019 2SS Join Date: Mar 2018
Location: Ohio
Posts: 103
|
I checked the grill again but I couldn't find any small pry slot and I am a little afraid to pry/pull down from top.
While I was looking around I found this little tab in the grill. Could this be the spot I am looking for? |
11-24-2018, 09:18 PM | #4 |
Drives: 2019 SS 1LE Join Date: Nov 2018
Location: PA
Posts: 6
|
I also have a 19 ss 1 le camaro and can not even budge the part of the grill to remove it .. WHAT IS THE SECERET TO REMOVE IT.
|
11-24-2018, 11:12 PM | #5 |
Drives: 2017 SS 1LE, 2017 Volt, 2013 Pilot Join Date: May 2014
Location: Colorado
Posts: 4,274
|
19's must have different grill...sorry, try owner's manual.
__________________
2017 SS 1LE | HBM | Vortech V3-Si supercharger (620RWHP and 575ft lbs) | PDR | Black Bowties | Illuminated Front Black Bowtie | Illuminated Door Sills | Smoked Tails | vented seats mod
|
11-25-2018, 12:22 AM | #6 |
Drives: 2019 2SS Join Date: Mar 2018
Location: Ohio
Posts: 103
|
|
11-25-2018, 05:57 AM | #7 |
Drives: 2017 Camaro SS Join Date: Nov 2018
Location: East Tennessee
Posts: 522
|
I'm getting this - and the license plate holder!
__________________
Kevin
Luceo Non Uro |
11-25-2018, 06:43 AM | #8 |
Drives: 2018 2SS 1LE Black Join Date: Aug 2018
Location: Cape Cod
Posts: 638
|
Did the guy in the video install that bracket upside down, I'm not seeing how this looks any better.
|
11-25-2018, 07:09 AM | #9 | |
Drives: 2017 Camaro SS Join Date: Nov 2018
Location: East Tennessee
Posts: 522
|
Quote:
When we retire and move to a free state that doesn't require the front plate we can easily switch to the tow hook.
__________________
Kevin
Luceo Non Uro |
|
11-25-2018, 07:50 AM | #10 |
Drives: '19 2SS M6. Join Date: Aug 2018
Location: CT
Posts: 340
|
The front plate frame that came on my car does not drill into the bumper but rather holds on with clamps.
If you remove it, no damage or marks.
__________________
2019 2SS, Shadow gray, 6mt, NPP, Magneride, Bose.
|
11-25-2018, 07:58 AM | #11 |
Drives: 2017 1LE Join Date: Nov 2017
Location: Brooks, GA
Posts: 697
|
Actually write a ticket for no front plate? Good grief...I mean I can see it being a PC stop if you're suspicious but talk about all the other crap going on that needs LE attention...
__________________
'17 Bright Yellow 1LE. PDR, STB, !CAGS
Borla 60606, 11925. Tony Mamo ported TB, ROTOFAB, !Sound Tube |
11-25-2018, 08:19 AM | #12 |
Drives: 2018 2SS 1LE Black Join Date: Aug 2018
Location: Cape Cod
Posts: 638
|
My dealer tossed it into the trunk to let me decide, I attached it with wire ties to get through inspection and then removed it. I don't see why wire ties couldn't be a permanent solution, they held well. I carry it around in the trunk and plan on talking my way out if it becomes necessary, so far no one has given a crap.
|
12-05-2018, 04:42 PM | #13 |
Drives: 2019 SS 1LE Join Date: May 2016
Location: New York
Posts: 18
|
If anyone was wondering, the zl1 addon license holder fits on the 2019 ss, just put mine on a few minutes ago.
Tip, when releasing the 1st clip, you want to pull up on the plastic piece of bumper. (the tow hook cover doesn't have much play up there) Once you release the 1st clip, you then release the 2nd one which is super easy. After the 2nd one is released, the side fins will slide out to the left. I took some pictures just in case. Send me a pm or I can post them in this thread if anyone is interested. |
12-05-2018, 05:21 PM | #14 | |
Drives: 2019 2SS Join Date: Mar 2018
Location: Ohio
Posts: 103
|
Quote:
|
|
|
|
Post Reply
|
Tags |
2019 camaro, license plate holder, tow hook |
Thread Tools | |
|
|